The objective is to set up SPI communication between VTI Technologies digital pressure sensor component and an MCU of an application device ATMEGA16L. In this code example: ?The MCU is configured ?SCP1000-D01 is initialized and configured ?The high resolution measurement mode is activated ?Temperature and pressure information is read always when the DRDY pin is in high state Please refer to the document "SCP1000 Product Family Specification 8260800" for further information on SCP1000 register addressing and SPI communication. This document applies to the SCP1000-D01.
标签： communication Technologies objective pressure
上传时间： 2017-06-17
上传用户：youmo81
DES工作的基本原理是，其入口参数有三个:key、data、mode。 key为加密解密使用的密钥，data为加密解密的数据，mode为其工作模式。当模式为加密模式时，明文按照64位进行分组，形成明文组，key用于对数据加密，当模式为解密模式时，key用于对数据解密。实际运用中，密钥只用到了64位中的56位，这样才具有高的安全性。
标签： DES
上传时间： 2014-11-22
上传用户：zukfu
Enter the Matrix MS-DOS screensaver. Sample of using bios functions (by int 10h) for text data output (monitor in the text mode) and keyboard input. Requires: Borland C++ 3.1 for DOS.
标签： screensaver functions Matrix MS-DOS
上传时间： 2013-11-29
上传用户：hopy
cuda简单例子，适合初学者，my first kernel
标签： cuda
上传时间： 2017-06-30
上传用户：181992417
This document gives the code for programming a CC2500 transceiver using Altera Stratix FPGA. The FPGA and CC2500 are connected through SPI mode with the FPGA as the master and CC2500 as the slave.
标签： programming transceiver document Stratix
上传时间： 2014-01-15
上传用户：wuyuying
Introduction to I/O Kit Device Driver Design Guidelines Chapter 1 The libkern C++ Runtime Chapter 2 libkern Collection and Container Classes Chapter 3 The IOService API Chapter 4 Making Hardware Accessible to Applications Chapter 5 Kernel-User Notification Chapter 6 Displaying Localized Information About Drivers Chapter 7 Debugging Drivers Chapter 8 Testing and Deploying Drivers Chapter 9 Developing a Device Driver to Run on an Intel-Based Macintosh
标签： Chapter Introduction Guidelines Runtime
上传时间： 2017-07-04
上传用户：冇尾飞铊
This program requires the DSP2833x header files. // // This program requires an external I2C RTC connected to // the I2C bus at address 0x6f. // // As supplied, this project is configured for "boot to SARAM" // operation. The 2833x Boot Mode table is shown below. // For information on configuring the boot mode of an eZdsp, // please refer to the documentation included with the eZdsp,
标签： requires program This external
上传时间： 2017-07-12
上传用户：dianxin61
This program requires the DSP2833x header files. // // As supplied, this project is configured for "boot to SARAM" // operation. The 2833x Boot Mode table is shown below. // For information on configuring the boot mode of an eZdsp, // please refer to the documentation included with the eZdsp,
标签： configured requires supplied program
上传时间： 2014-01-10
上传用户：lixinxiang
This software is developed to provide ease with controller design. For PID control, options are given to design and analyse the compensated and uncompensated system. You are free to choice among Proportional PI, PD and PID mode of control. Both frequency and time domain characteristics can be observed. Special Menus are given to observe time and frequency response plots. For Statefeedback controller similar options are given. But this is limited to second order system only.
标签： controller developed software control
上传时间： 2017-07-25
上传用户：aysyzxzm
RS_latch using vhdl, When using static gates as building blocks, the most fundamental latch is the simple SR latch, where S and R stand for set and reset. It can be constructed from a pair of cross-coupled NOR (Not OR) logic gates. The stored bit is present on the output marked Q. Normally, in storage mode, the S and R inputs are both low, and feedback maintains the Q and Q outputs in a constant state, with Q the complement of Q. If S (Set) is pulsed high while R is held low, then the Q output is forced high, and stays high when S returns to low similarly, if R (Reset) is pulsed high while S is held low, then the Q output is forced low, and stays low when R returns to low.
标签： using fundamental the RS_latch
上传时间： 2017-07-30
上传用户：努力努力再努力
