FatFs06.rar FatFs is a generic file system module to implement the FAT file system to small embedded systems. The FatFs is written in compliance with ANSI C, therefore it is independent of hardware architecture. It can be incorporated into cheap microcontrollers, such as 8051, PIC, AVR, SH, Z80, H8, ARM and etc..., without any change.
标签： system FatFs file implement
上传时间： 2016-11-17
上传用户：chenxichenyue
The application described in this document is for a product that is subject to continuous developments and improvements. All particulars of the product and its use contained in this document are given by ARM in good faith. However, all warranties implied or expressed, including but not limited to implied warranties of merchantability, or fitness for purpose, are excluded.
标签： application continuous developmen described
上传时间： 2016-12-16
上传用户：dave520l
In term project, we will take the baseline JPEG codec in ARM-based platform system as an example to practice the design flow in SoC. We divide the project into three parts, and the goal of each part is described as follow. Part I: Design a baseline JPEG software codec in C/C++ and port it to ARM core,(ARM7TDMI, ARM720T, or ARM922T.) Part II: Make use of virtual prototype to integrate/verify the hardware and software. Part III: Verify your soft IP in target environment.
标签： ARM-based baseline platform project
上传时间： 2017-02-15
上传用户：363186
RTOS ThreadX Real-Time Embedded Multithreading: Using ThreadX and ARM Designations used by companies to distinguish their products are often claimed as trademarks. In all instances where CMP is aware of a trademark claim, the product name appears in initial capital letters, in all capital letters, or in accordance with the vendor鈥檚 capitalization preference. Readers should contact the appropriate companies for more complete information on trademarks and trademark registrations. All trademarks and registered trademarks in this book are the property of their respective holders.
标签： ThreadX Multithreading Designations Real-Time
上传时间： 2013-12-18
上传用户：ZJX5201314
describe the operation of theARMcore from a product developer鈥檚 perspective with a clear emphasis on software. Because we have written this book specifically for engineers who are experienced with embedded systems development but who may be unfamiliar with the ARM architecture, we have assumed no previous ARM experience.
标签： perspective theARMcore operation developer
上传时间： 2017-05-01
上传用户：AbuGe
This code proposes genetic algorithm (GA) to optimize the point-to-point trajectory planning for a 3-link robot arm. The objective function for the proposed GA is to minimizing traveling time and space, while not exceeding a maximum pre-defined torque, without collision with any obstacle in the robot workspace.
标签： point-to-point trajectory algorithm proposes
上传时间： 2013-12-21
上传用户：chenxichenyue
Architecture and Implementation ? ? Cortex -A8 of the ARM Microprocessor October 2005 Introduction ? ? The ARM Cortex -A8 microprocessor is the first applications microprocessor in ARM!ˉs new Cortex family. With high performance and power efficiency, it targets a wide variety of mobile and consumer applications including mobile phones, set-top boxes,
标签： Implementation Microprocessor Architecture October
上传时间： 2013-12-15
上传用户：daoxiang126
Architecture and Implementation ? ? Cortex -A8 of the ARM Microprocessor October 2005 Introduction ? ? The ARM Cortex -A8 microprocessor is the first applications microprocessor in ARM!ˉs new Cortex family. With high performance and power efficiency, it targets a wide variety of mobile and consumer applications including mobile phones, set-top boxes,
标签： Implementation Microprocessor Architecture October
上传时间： 2017-07-23
上传用户：lizhizheng88
摘要：本文介绍了一个基于ARM的线性CCD高速采集系统，系统中选择了高速线性CCD和高速ADC，因为ADC的采祥速度相对ARM的工作时钟频率较慢，所以使用CPLD和FIFO作为A/D和ARM之间的1/0接口，它使电路工作在更加平稳、简洁而易丁控制，同时也提高了ARM的工作效率。为了提高通信速度，这里采用通用申行总线（USB）技术米与PC进行通信。ARM是用来控制主处理器的数据采集，数据的计算和数据传输。结果证明，整个系统能高效运作。该系统可应用于高速数据采集及多路模拟信号的工作环境下。1引言在电气化铁路，为了扩大对电力机车受电弓的寿命，所以要使受电弓滑块磨损均匀，接触线的直线段（电气化铁路供电线）排列为曲折路线（弯段被安排成折线的形式）。之间的接触线的定位点和受电弓轨道中心线距离称为错开值，这是一种接触线的关键指标。错开值是不可忽视的，这个值过小会影响到受电弓滑块磨损的均匀性，从而影响到延长使用寿命的目的，然而，在某些情况下（比如陷入了激烈的风中），造成大范围的在屋部的横向运动（并且速度越快，受电弓的左右摆动越剧烈），按触线将在某些部分将会超过受电弓的有效工作长度，从而使错开，接触线值超出标准范围的错开值，导致了当前连接的破坏，甚至导致了会产生受电弓事故的错识运行。受电马与滑触线发生故障，将导致列车正常运行的中断，从而对铁路运输产生严亚的影响。为了避免这些情况，错开伯及其变化应经常性地予以测试。因此，一个机车的接触线式在线监测系统，及与其配套的数据采集系统被开发出来，它的工作是实时地、迅速地计算错开值。
上传时间： 2022-06-23
上传用户：kingwide
ARM Cotrex-M3权威指南 英文 超清版.PDF
上传时间： 2013-06-14
上传用户：eeworm
