为设计高效率、低损耗的PFC电路,本文基于UCC28019进行电路设计。以UCC28019输出的PWM波形来控制Boost升压斩波为核心电路,使电路中的电容交替地充放电、电感交替的储存和释放能量,最后实现在输入AC20V~24V电压情况下稳定输出DC38V。测试结果表明,系统实现效率为95%左右,电压调整率小于1%,电源功率因数0.99。交流输入电压为19.0-25.8 V时,输出直流电压稳定性较好,电感无明显啸叫且纹波小,具有一定的带负载能力和实用性。In order to design the PFC circuit with high efficiency and low loss,this paper designs the circuit based on UCC28019.The PWM waveform output by UCC28019 is used to control boost chopper as the core circuit,which alternately charges and discharges capacitors,stores and releases energy by inductors,and finally achieves stable output of DC38 V under the input voltage of AC20 V~24 V.The test results show that the system achieves about 95% efficiency,the voltage adjustment rate is less than 1%,the power factor is 0.99,and the AC input voltage is 19.0-25.8 V.The output DC voltage stability is good,the inductance has no obvious whistle and the ripple is small,so it has certain load capacity and practicability.
上传时间： 2022-04-03
上传用户：
目的:自主研制一款超声手术刀电源控制系统,以减少能量的消耗,维持手术刀的正常温度。方法:对超声换能器在谐振附近的等效电路建立模型,并设计基于数字信号处理(DSP)的超声手术刀的硬件控制系统。结果:经对电源控制系统的电路和工作性能测试,生成的电流和电压的有效值等参数,能够及时调整电源的频率,并达到预期的功能指标,使超声手术刀工作在谐振状态。结论:以DSP为核心设计的超声手术刀电源控制系统,测试指标均能够达到预期的要求,能够使系统在谐振状态下工作。Objective: To independently develop a power control system of ultrasonic scalpel so as to reduce the energy consumption and maintain the normal temperature of ultrasonic scalpel. Methods: In this paper, the model of equivalent circuit of ultrasonic transducer nearby syntony was built up, and the hardware control system of ultrasonic scalpel based on digital signal processing(DSP) was designed. Results: Through testing the circuit and work performance of power control system, the series of parameters such as effective value and so on which were produced by this system could adjust frequency of power source in time and attain anticipative functional indicator, and it took the ultrasonic scalpel to work in syntonic situation. Conclusion: The tested indicators of power control system of ultrasonic scalpel based on the kernel design of DSP can attain anticipative requirement, and can take this system to work in syntonic situation.
上传时间： 2022-04-03
上传用户：bluedrops
本文首次设计并验证了基于macom三合一芯片设计的光模块电路,该电路旨在提供一种满足SFF-8472中规定的数字诊断功能的低成本SFP+模块。电路采用激光器驱动、限幅放大器、控制器以及时钟恢复单元集成的单芯片,在保证高精度数字诊断功能基础上,实现了低成本高可靠的特点。该电路在光接收接口组件与激光器驱动和限幅放大器单元的限幅放大器部分之间接入滤波器来提高模块的灵敏度及信号质量。在控制器单元的数字电位器的引脚上采用外加电阻的方式避免出现上电不发光的故障问题。该研究结果为下一代SFP-DD光模块设计与开发工作,奠定了一定的理论与实践基础。This paper designs and validates the optical module circuit based on the MACOM Trinity chip for the first time.This circuit aims to provide a low-cost SFP module which meets the digital diagnosis function specified in SFF-8472.The circuit uses a single chip integrated with laser driver,limiting amplifier,controller and clock recovery unit.On the basis of ensuring high precision digital diagnosis function,it achieves the characteristics of low cost and high reliability.The circuit connects a filter between the optical receiving interface module and the limiting amplifier part of the laser driver and limiting amplifier unit to improve the sensitivity and signal quality of the module.The pin of the digital potentiometer in the controller unit is equipped with an external resistance to avoid the problem of power failure.The research results lay a theoretical and practical foundation for optical module design in high-speed data center.
上传时间： 2022-04-03
上传用户：
抢答器是一种智力竞赛常用的器件,抢答器的设计方法千差万别,文章利用常用的数字电子器件,设计了八路抢答器电路的设计、仿真及实现的全过程,提出两种可行的设计方案:方案1采用74ls373实现电路锁存,74ls148实现电路编码,74ls74及数码管实现电路显示;方案二采用CD4511BCN和LMC555CM集成电路及数码管实现抢答器的控制和显示。本文设计用的器件简单,容易理解,适用于初学电子技术的人员。Answer scrambler is a common device in intelligence competition, and its design methods vary greatly. This paper designs the whole process of design, simulation and Realization of the circuit of eight-way answer scrambler by using common digital electronic devices, and puts forward two feasible design schemes: scheme 1 uses 74 ls373 to realize circuit latching, 74 ls148 to realize circuit coding,74 ls74 and digital tube to realize circuit. The second scheme uses CD4511 BCN, LMC555 CM integrated circuit and digital tube to control and display the answerer. The device designed in this paper is simple and easy to understand, and it is suitable for the beginners of electronic technology.
标签： 抢答器
上传时间： 2022-04-05
上传用户：
实验教学一直是工科教学中不可或缺的组成部分,对培养学生的动手能力,独立思考能力,创新思维与发散思维具有重要的作用。针对目前电路教学实验中电路仿真实验与实物电路实验各自独立,无法统一问题,提出将仿真电路实验与实物电路实验有机的结合同步操作,并使用Web发布实现远程实验操作。采用Multisim作为电路实验仿真平台,NI Eiviss II作为实物电路实验硬件平台,运用LabVIEW整合Multisim电路仿真实验与实物电路实验,实现仿真与实物实验有机结合,两种实验可同步进行。学生在仿真实验中先可探索实验,然后做实物实验。同时运用LabVIEW开发出实验过程人机交互操作接口界面,使用过程中效果良好。Experimental teaching has always been an indispensable part of engineering education.And it always plays an important role in cultivating students'practical ability,independent thinking ability,innovative thinking and divergent thinking.But simulation experiment and physical experiment cannot be unified in the circuit teaching experiment at present.In order to solve this problem,this paper proposes to combine organically the simulation circuit experiment with physical circuit experiment,and synchronously operate them.This paper uses the WEB publishing to achieve remote experimental operation.Multisim is used as the circuit simulation platform,and NI Eiviss II is used as the physical circuit hardware platform.Multisim circuit simulation experiment and physical circuit experiment are implemented by LabVIEW to realize the combination of simulation experiment and physical experiment.Students do explore experiments in simulation experiment firstly,and then do physical experiment.And this paper uses LabVIEW to develop the experimental man-machine interface.
上传时间： 2022-04-05
上传用户：
为了提高超高频RFID系统中阅读器在低信噪比的情况下仍具有较高的识别能力,提出一种基于FPGA系统结合软件无线电方法实现超高频RFID射频前端电路方案。超高频射频识别系统必须符合EPC Class 1generation 2标准,所设计的电路系统以Xilinx公司的XC6SLX16-2CSG324FPGA芯片为硬件基础,将数字基带调制解调和中频滤波电路在FPGA系统中设计实现,重点阐述了射频前端电路的设计结构、AD/DA转换电路,以及数字滤波器的设计。实验结果表明,所设计的超高频RFID阅读器简化了前端电路系统结构,提升了稳定性,增强了抗干扰能力。该电路系统在信噪比较低的情况下,能够较好地实现915MHz频率的射频接收和发送。In order to improve the reader UHF RFID system still has a higher ability to identify,in the case of low signal-to-noise ratio.The UHF RFID systems must comply with EPC Class 1 generation 2 standard.In this paper,the design of the circuit system based on Xilinx＇s XC6SLX16-2CSG324 FPGA chip,and presents UHF RFID RF front-end circuit with software radio based on FPGA system.Digital baseband modem and IF filter circuit is designed and implemented in the FPGA system,and focused on designing the structure of the RF front-end circuit,AD/DA conversion circuits,and digital filter.Experimental results show that the UHF RFID reader de...
标签： 915mhz 超高频 rfid 阅读 射频 前端 电路 设计
上传时间： 2022-04-17
上传用户：shjgzh
介绍一种万能模拟信号输入采集电路,可以同时支持电压、电流、热电偶、热电阻等常见的工业类型信号,方便后级电路的测量。该研究成果通过不断优化和完善,已成功应用到了中控仪表的新产品中。The paper introduces a collection circuit of universal signal input. The circuit support voltage, current, thermocouple, thermal resistance and other common industrial type signal. The research results, which has been continuous optimized and improved, has been successfully applied to the new production of Zhejiang Supcon Instrument Co., Ltd.
标签： 采集电路
上传时间： 2022-04-21
上传用户：slq1234567890
超声波换能器作为一种实用的检测手段，能实现声波所携带的信息和电能之间转换。它的性能优良，价格低廉，操作方便，易于调试，因此在工农业生产中发挥着重要的作用。但目前换能器驱动电路的发射频率多为40 kHz，本文针对1 MHz的超声波换能器电路进行了设计，主要介绍了它的发射驱动电路和接收驱动电路的设计方案，并对它们的功能进行了详细地说明。最后搭建实验平台，并对电路的输入、输出模块进行了测试。实验结果表明，换能器电路运行良好，可以为超声波高精度测量领域的应用提供参考。As a practical means of detection, ultrasonic transducer can realize the conversion between theinformation carried by sound wave and electric energy.It has the advantages of excellent performance,low cost, convenient operation and debugging, so plays an important role in industrial and agriculturalproduction.However, the transmitting frequency of the driving circuit for most transducer is 40 kHz.Thecircuit of 1 MHz ultrasonic transducer is designed In this paper. It mainly introduces the emissive drivingcircuit and the receiving circuit design and the detailed function of them. Finally, the experimentalplatform is built, and the circuit of input and output were tested. Experiments show that the transducer＇ s...
上传时间： 2022-04-28
上传用户：
本文提出基于AD2S1210的旋变信号转换电路,给出了具体的电路实现方法和配置方法.相比以往的RDC方案,本系统具有精度高,设计灵活,可靠性高等特点,可广泛应用于各种伺服系统中.In this paper, the switching signal conversion circuit based on ADS1210 is proposed, and the specific circuit implementation and configuration method are given. Compared with the previous RDC scheme, this system has the characteristics of high precision, flexible design and high reliability, and can be widely used in various servo systems.
标签： ad2s1210
上传时间： 2022-05-04
上传用户：
基于TMS320F28335的超声波流量计硬件原理图+软件源码本文以TMS320F28335 处理器为核心，设计一种用于管道流量测量的超声波流量计。系统硬件由核心板，超声波发射和接收电路，切换电路，超声换能器，基于ADS805 的高速信号采集电路，人机交互以及电源等模块构成。采用时差法进行管道流量测量，时差测量采用SCOT 加权的广义互相关时延估计算法。本论文设计的超声波流量计具有测量速度快、准确性好、成本低等优点。关键字：C2000，超声波，流量，广义互相关算法AbstractA kind of ultrasonic flowmeter using for the pipe flow measurement is designed based onTMS320F28335 in this paper. The system hardware consists of the following parts: the core board,ultrasonic signal transmitter and receiver circuits, switch circuit, ultrasonic transducer, signalacquisition circuit based on ADS805, human-computer interaction module and power supplymodule, etc. The system use the method of time difference for pipeline flow measurement and thetime difference is calculated by the time-delay algorithm of SCOT weighted generalizedcross-correlation. The ultrasonic flowmeter has the features of high testing speed, high precisionand low cost, etc.Keywords: C2000,Ultrasonic, Flow, Generalized Cross-Correlation Algorithm
标签： tms320f28335 超声波流量计
上传时间： 2022-05-06
上传用户：
