For a variety of reasons, it is desirable to charge batteriesas rapidly as possible. At the same time, overchargingmust be limited to prolong battery life. Such limitation ofovercharging depends on factors such as the choice ofcharge termination technique and the use of multi-rate/multi-stage charging schemes. The majority of batterycharger ICs available today lock the user into one fixedcharging regimen, with at best a limited number ofcustomization options to suit a variety of application needsor battery types. The LTC®1325 addresses these shortcomingsby providing the user with all the functionalblocks needed to implement a simple but highly flexiblebattery charger (see Figure 1) which not only addressesthe issue of charging batteries but also those of batteryconditioning and capacity monitoring.
上传时间： 2013-10-19
上传用户：royzhangsz
在理论分析循环码编码和译码基本原理的基础上，提出了基于单片机系统的(24，16)循环码软件实现编码、译码的方案。仿真结果表明(24，16)循环码能有效地克服来自通讯信道的干扰，保证数据通信的可靠及系统的稳定，使误码率大幅度降低。本论文对(24，16)循环码的研究结果表明，可以有效地降低错误概率和提高系统的吞吐量，实现纠错仅需要在接收端增加有限的存储空间和计算复杂度，具有一定的实用价值。 Abstract: Based on analyzing the theory of encoding and decoding of cyclic code， this paper showed the schemes of encoding and decoding of(24，16)cyclic code by the software and based on microcontroller. Simulation results show that using (24，16) cyclic codes can effectively overcome the interference from communication channel， ensure the reliability and stability of data communication systems， and reduce the bit error rate greatly. The results of this paper show that by using the (24，16) cyclic code， the error rate can be reduced and the system throughput can be improved. Meanwhile， the system only needs to enlarge limited storage space and computation the complexity at the receiving end to realize error correction. Thus the (24，16) cyclic code has a practical value.
上传时间： 2013-11-09
上传用户：gaoliangncepu
The MAX9257/MAX9258 programmable serializer/deserializer (SerDes) devices transfer both video data and control signals over the same twisted-pair cable. However, control data can only be transmitted during the vertical blank time, which is indicated by the control-channel-enabled output (CCEN) signal. The electronic control unit (ECU) firmware designer needs to know how quickly to respond to the CCEN signal before it times out and how to calculate this duration. This application note describes how to calculate the duration of the CCEN for the MAX9257/MAX9258 SerDes chipset. The calculation is based on STO timeout, clock frequency, and UART bit timing. The CCEN duration is programmable and can be closed if not in use.
上传时间： 2014-01-24
上传用户：xingisme
针对目前使用的RS232接口数字化B超键盘存在PC主机启动时不能设置BIOS，提出一种PS2键盘的设计方法。基于W78E052D单片机，采用8通道串行A/D转换器设计了8个TGC电位器信息采集电路，电位器位置信息以键盘扫描码序列形式发送，正交编码器信号通过XC9536XL转换为单片机可接收的中断信号，软件接收到中断信息后等效处理成按键。结果表明，在满足开机可设置BIOS同时，又可实现超声特有功能，不需要专门设计驱动程序，接口简单，成本低。 Abstract: Aiming at the problem of the digital ultrasonic diagnostic imaging system keyboard with RS232 interface currently used couldn?蒺t set the BIOS when the PC boot， this paper proposed a design method of PS2 keyboards. Based on W78E052D microcontroller，designed eight TGC potentiometers information acquisition circuit with 8-channel serial A/D converter， potentiometer position information sent out with keyboard scan code sequentially.The control circuit based on XC9536 CPLD is used for converting the mechanical actions of the encoders into the signals that can be identified by the MCU， software received interrupt information and equivalently treatmented as key. The results show that the BIOS can be set to meet the boot， ultrasound specific functionality can be achieved at the same time， it does not require specially designed driver，the interface is simple and low cost.
上传时间： 2013-10-10
上传用户：asdfasdfd
详细介绍工控软件组态王与单片机多机串口通讯的设计原理。分析组态王提供的直接与单片机串口通信方法的优点，给出系统基于RS-485总线传输的接口电路原理图。根据组态王提供的通讯协议和单片机多机串口通讯的原理，给出程序设计流程与思路。 Abstract: In this paper，the design principle of communication between multi-SCM and KingView by serial ports is described in detail.We analysis the advantage of method supplied by KingView,by which KingView can communicate with serial ports of SCM directly，and provide the system’s interface circuit based on the RS-485transmission line.We provide flow diagram of programming and thinking on the basis of communication protocol supplied by KingView and principle of communication among multi-SCM through serial ports.
上传时间： 2013-12-19
上传用户：tecman
以89S52单片机和EP1C6Q240C8型FPGA为控制核心的多功能计数器，是由峰值检波、A/D转换、程控放大、比较整形、移相网络部分组成,可实现测量正弦信号的频率、周期和相位差的功能。多功能计数器采用等精度的测量方法，可实现频率为1Hz～10MHz、幅度为0.01～5Vrms的正弦信号的精确测频，以及频率为10Hz～100kHz、幅度为0.5～5Vrms的正弦信号精确测相。液晶显示器能够实时显示当前信号的频率、周期和相位差。该多功能计数器精度高，界面友好，实用性强。 Abstract: A multi-function counter，which uses89S52MCU and EP1C6Q240C8FPGA as a control core，consists of peak detector，A/D conversion，program-controlled amplification，compared shaping and phase-shifting network part.The counter measures the frequency，period and phase of sinusoidal signal.With the equal precision method,the multi-function counter achieves the precise frequency measurement of the sinusoidal signal which its frequency is from1Hz to10MHz，its amplitude is from0.01Vrms to5Vrms，as well as the accurate phase measurement of the sinusoidal signal which its frequency is from10Hz to100kHz，its amplitude is from0.5Vrms to5Vrms.The LCD monitor real-time displays the frequency，period and phase difference of current signal.The multi-function counter features high precision，friendly interface，and strong practical.
上传时间： 2013-11-15
上传用户：gy592333
介绍一种基于C8051F060单片机和NAND Flash的数据采集存储系统，该系统可实现3路信号采样，每路采样率为5KS/s,通过异步串行通信接口实现数据传输。并详细说明系统的软件设计。 Abstract: An acquisition and storage system based on C8051F060and NAND Flash is designed in this paper.The system is used to sample three-channel of signal,5KSPS each channel,and can upload data to test bench through UART（Universal Asynchronous Receiver/Transmitter）.The software design is discussed in detail.
上传时间： 2013-10-12
上传用户：Jesse_嘉伟
量测/测试所面临之问题 此测试验证上，要使用NI公司之LAB VIEW及DAQ CARD来取代AUDIO PRECISION及其所附软体ATS。首先需克服硬体解析度上的差异，再来是FFT（FAST FOURIER TRANSFORM,快速传立业转换）演算未予的撰写，这将会影响MULTI-TONE讯号上PEAK值的侦测。另外，以RS-232为I/O介面，并呼叫客户所提供之DLL档来与DUT内的IC沟通，但因LAB VIEW无法直接呼叫其STRUCTURE，故需用VC++再编译一层新的DLL来供LAB VIEW使用。
上传时间： 2013-12-13
上传用户：longlong12345678
介绍一种基于单片机的多路温度采集及监控系统，能够测量6路温度信号，具有计算机联网功能，各测量点可以单独监控和设置，可根据用户的需求自动控制。测量温度范围为-10 ℃～200 ℃，控制方式采用模拟量调压模式。该系统具有控制精度高、冲击小等特点。 Abstract: A temperature collecting and surveillance-controlling system based on sing-chip microcomputer is introduced. It can measure 6 channel signal of the temperature,and it has a function of network connection.The temperature measure points can be monitored and located, it can be controlled automatic according to user’s demand.The temperature range is -10℃ to 200℃.The model of control is adjustable voltage with simulation. It features high precision and little impact.
上传时间： 2013-10-23
上传用户：bjgaofei
为解决输油管道温度压力参数实时监测的问题，设计了以C8051F930单片机作为控制核心的超低功耗输油管道温度压力远程监测系统。现场仪表使用高精度电桥采集数据，通过433 MHz短距离无线通信网络与远程终端RTU进行通信，RTU通过GPRS网络与PC上位机进行远程数据传输，在上位机中实现数据存储和图形化界面显示，从而实现输油管道温度压力参数的实时监测和异常报警。经实验证明，该系统的12位数据采集精度满足设计要求，漏码率小于1%，正常工作时间超过5个月，能实时有效地监测输油管道的温度压力参数，节省大量人工成本，有效预防管道参数异常造成的经济损失和环境污染。 Abstract: In order to solve the problems on real-time monitoring of pipeline temperature and pressure parameters， the ultra-low power remote pipeline temperature and pressure monitoring system was designed by using the single chip processor C8051F930 as the control core. The high-precision electric bridge was used in field instruments for data collection， the 433MHz short-range wireless communication network was used to make communication between field instrument and RTU， the GPRS was used by the RTU to transmit data to the PC host computer， and the data was stored and displayed in the PC host computer， so the real-time monitoring and exception alerts of pipeline temperature and pressure parameters were achieved. The experiment proves that the system of which error rate is less than 1% over five months working with the 12-bit data acquisition accuracy can effectively monitor the pipeline temperature and pressure parameters in real time， it saves a lot of labor costs and effectively prevents environmental pollution and economic losses caused by abnormal channel parameters.
上传时间： 2013-11-07
上传用户：cuibaigao
