本系统采用电动机电枢供电回路串接采样电阻的方式来实现对小型直流有刷电动机的转速测量。该系统主要由二阶低通滤波电路,小信号放大电路、单片机测量显示电路、开关稳压电源电路等组成。同时自制电机测速装置,用高频磁环作为载体,用线圈绕制磁环,利用电磁感应原理检测电机运行时的漏磁,将变化的磁场信号转化为磁环上的感应电流。用信号处理单元电路将微弱电信号转化为脉冲信号,送由单片机检测,从而达到准确测量电机的速度的要求。In this system, the sampling resistance of armature power supply circuit is connected in series to measure the speed of small DC brush motor. The system is mainly composed of second-order low-pass filter circuit, small signal amplifier circuit, single-chip measurement and display circuit, switching regulated power supply circuit and so on. At the same time, the self-made motor speed measuring device uses high frequency magnetic ring as the carrier, coil winding magnetic ring, and electromagnetic induction principle to detect the leakage of magnetic field during the operation of the motor, which converts the changed magnetic field signal into the induced current on the magnetic ring. The weak electric signal is transformed into pulse signal by signal processing unit circuit, which is sent to single chip computer for detection, so as to meet the requirement of accurate measurement of motor speed.
标签： 直流电动机
上传时间： 2022-03-26
上传用户：
近年来反季节种植已成火热趋势,温室大棚的普及十分迅速,而温室大棚对自动化、智能化的要求也越来越迫切,本系统将温室大棚的温湿度、二氧化碳浓度各个方面的检测,通风、浇灌、温度、喷洒农药等各个方面的控制进行综合系统研究,实现温室大棚对自动化、智能化的要求。这一系统是基于单片机控制的智能检测,控制系统包含单片机主控模块、感应检测模块、传感模块,显示、控制模块等[1]。从而提高温室大棚的种植效率,减少劳动力,提高利润等。In recent years,counter-season planting has become a hot trend featuring the rapid popularization of greenhouse and urgent requirement for the automation and intellectualization of greenhouse.This paper offers a comprehensive and systematic study of the monitoring of temperature,humidity and carbon dioxide concentration in the greenhouse and the control of ventilation,irrigation,temperature and pesticide spraying in order to achieve automation and intellectualization in greenhouse.This system is based on the intelligent detection controlled by single chip computer with the control system including the main control module,induction detection module,sensing module,display and control module of single chip computer,which is effective in improving planting efficiency of greenhouse,reducing labor force and increasing profits.
上传时间： 2022-03-27
上传用户：
以STC12C5A60S2单片机为控制核心,采用2.4G(JF24D)无线遥控模块进行无线发射与接收,设计了一种双电机遥控船模控制系统.该系统通过切换档杆实现前进后退,方向盘左右转动、暂停按钮等控制直流电机的正转、反转、暂停,使得电机驱动的遥控船模实现前进后退、左右转向、暂停等功能,有效解决了驱动功率小和船模之间相互干扰等问题,可广泛应用于遥控船模领域.Using STC12C5A60S2 single-chip microcomputer as the controller and 2.4 G(JF24D)wireless remote control module for wireless transmission and reception, a dual-motor remote control ship model control system is designed. The system realizes forward and backward by switching the gear lever. The steering wheel rotates left and right and the pause button controls the forward, reverse and pause of the dc motor. The remote controller of ship model driven by the motor realizes forward and backward, left and right steering, pause and other functions. The ship model control system can effectively solve the problems of small driving power and mutual interference between ship models, and can be widely used in the field of remote controller of ship model.
上传时间： 2022-03-27
上传用户：
适用于ADS2019版本的。。村田公司生产的电容、电感等器件的model的desigekits
标签： ads
上传时间： 2022-04-02
上传用户：
为设计高效率、低损耗的PFC电路,本文基于UCC28019进行电路设计。以UCC28019输出的PWM波形来控制Boost升压斩波为核心电路,使电路中的电容交替地充放电、电感交替的储存和释放能量,最后实现在输入AC20V~24V电压情况下稳定输出DC38V。测试结果表明,系统实现效率为95%左右,电压调整率小于1%,电源功率因数0.99。交流输入电压为19.0-25.8 V时,输出直流电压稳定性较好,电感无明显啸叫且纹波小,具有一定的带负载能力和实用性。In order to design the PFC circuit with high efficiency and low loss,this paper designs the circuit based on UCC28019.The PWM waveform output by UCC28019 is used to control boost chopper as the core circuit,which alternately charges and discharges capacitors,stores and releases energy by inductors,and finally achieves stable output of DC38 V under the input voltage of AC20 V~24 V.The test results show that the system achieves about 95% efficiency,the voltage adjustment rate is less than 1%,the power factor is 0.99,and the AC input voltage is 19.0-25.8 V.The output DC voltage stability is good,the inductance has no obvious whistle and the ripple is small,so it has certain load capacity and practicability.
上传时间： 2022-04-03
上传用户：
目的:自主研制一款超声手术刀电源控制系统,以减少能量的消耗,维持手术刀的正常温度。方法:对超声换能器在谐振附近的等效电路建立模型,并设计基于数字信号处理(DSP)的超声手术刀的硬件控制系统。结果:经对电源控制系统的电路和工作性能测试,生成的电流和电压的有效值等参数,能够及时调整电源的频率,并达到预期的功能指标,使超声手术刀工作在谐振状态。结论:以DSP为核心设计的超声手术刀电源控制系统,测试指标均能够达到预期的要求,能够使系统在谐振状态下工作。Objective: To independently develop a power control system of ultrasonic scalpel so as to reduce the energy consumption and maintain the normal temperature of ultrasonic scalpel. Methods: In this paper, the model of equivalent circuit of ultrasonic transducer nearby syntony was built up, and the hardware control system of ultrasonic scalpel based on digital signal processing(DSP) was designed. Results: Through testing the circuit and work performance of power control system, the series of parameters such as effective value and so on which were produced by this system could adjust frequency of power source in time and attain anticipative functional indicator, and it took the ultrasonic scalpel to work in syntonic situation. Conclusion: The tested indicators of power control system of ultrasonic scalpel based on the kernel design of DSP can attain anticipative requirement, and can take this system to work in syntonic situation.
上传时间： 2022-04-03
上传用户：bluedrops
实验教学一直是工科教学中不可或缺的组成部分,对培养学生的动手能力,独立思考能力,创新思维与发散思维具有重要的作用。针对目前电路教学实验中电路仿真实验与实物电路实验各自独立,无法统一问题,提出将仿真电路实验与实物电路实验有机的结合同步操作,并使用Web发布实现远程实验操作。采用Multisim作为电路实验仿真平台,NI Eiviss II作为实物电路实验硬件平台,运用LabVIEW整合Multisim电路仿真实验与实物电路实验,实现仿真与实物实验有机结合,两种实验可同步进行。学生在仿真实验中先可探索实验,然后做实物实验。同时运用LabVIEW开发出实验过程人机交互操作接口界面,使用过程中效果良好。Experimental teaching has always been an indispensable part of engineering education.And it always plays an important role in cultivating students'practical ability,independent thinking ability,innovative thinking and divergent thinking.But simulation experiment and physical experiment cannot be unified in the circuit teaching experiment at present.In order to solve this problem,this paper proposes to combine organically the simulation circuit experiment with physical circuit experiment,and synchronously operate them.This paper uses the WEB publishing to achieve remote experimental operation.Multisim is used as the circuit simulation platform,and NI Eiviss II is used as the physical circuit hardware platform.Multisim circuit simulation experiment and physical circuit experiment are implemented by LabVIEW to realize the combination of simulation experiment and physical experiment.Students do explore experiments in simulation experiment firstly,and then do physical experiment.And this paper uses LabVIEW to develop the experimental man-machine interface.
上传时间： 2022-04-05
上传用户：
为了提高超高频RFID系统中阅读器在低信噪比的情况下仍具有较高的识别能力,提出一种基于FPGA系统结合软件无线电方法实现超高频RFID射频前端电路方案。超高频射频识别系统必须符合EPC Class 1generation 2标准,所设计的电路系统以Xilinx公司的XC6SLX16-2CSG324FPGA芯片为硬件基础,将数字基带调制解调和中频滤波电路在FPGA系统中设计实现,重点阐述了射频前端电路的设计结构、AD/DA转换电路,以及数字滤波器的设计。实验结果表明,所设计的超高频RFID阅读器简化了前端电路系统结构,提升了稳定性,增强了抗干扰能力。该电路系统在信噪比较低的情况下,能够较好地实现915MHz频率的射频接收和发送。In order to improve the reader UHF RFID system still has a higher ability to identify,in the case of low signal-to-noise ratio.The UHF RFID systems must comply with EPC Class 1 generation 2 standard.In this paper,the design of the circuit system based on Xilinx＇s XC6SLX16-2CSG324 FPGA chip,and presents UHF RFID RF front-end circuit with software radio based on FPGA system.Digital baseband modem and IF filter circuit is designed and implemented in the FPGA system,and focused on designing the structure of the RF front-end circuit,AD/DA conversion circuits,and digital filter.Experimental results show that the UHF RFID reader de...
标签： 915mhz 超高频 rfid 阅读 射频 前端 电路 设计
上传时间： 2022-04-17
上传用户：shjgzh
为解决移相全桥电路驱动及相角控制问题,设计了一种数字控制的移相全桥驱动电路.以TPL521为光耦隔离、IR2110为栅极驱动芯片.由DSP产生PWM信号,经过光耦隔离和逻辑电路后送至IR2110进行相角控制.文章对IR2110驱动电路原理进行分析及参数进行设计,对TMS320F28335进行设置并给出部分代码.实验结果表明：通过TMS320F28335可产生的不同相角的PWM波形,满足了移相全桥对不同相角控制的要求.In order to solve the problem of phase-shifted full-bridge circuit driving and phase angle control,a digitally controlled phaseshifted full-bridge driving circuit was designed. TPL521 optocoupler isolation,IR2110 gate driver chip. PWM signals are generated by the DSP and sent to the IR2110 for phase angle control after optocoupler isolation and logic circuits. This text carries on the analysis to the principle of IR2110 drive circuit and parameter design,set up and give out some code to TMS320F28335. The experimental results show that the PWM waveforms with different phase angles generated by TMS320F28335 can meet the requirements of phase-shifted full-bridge control for different phase angles.
上传时间： 2022-05-03
上传用户：zhanglei193
这是一本英文版的MPC的MATLAB教程，讲这一块的资料太少了，故上传一本。MPC is one of the few areas that has received on-going interest from researchers in both the industrial and cademic communities.Four major aspects of model predictive control make the design methodology attractive to both practitioners and academics.This is particularly attractive to industry where tight profit margins and limits on the process operation are inevitably present. The third aspect is the ability to perform on-line process optimization. The fourth aspect is the simplicity of the design framework in handling all these complex issues.
标签： 模型预测控制
上传时间： 2022-05-05
上传用户：zhanglei193
