高通(Qualcomm)蓝牙芯片QCC5144_硬件设计详细指导书（官方内部培训手册）其内容是针对硬件设计、部分重要元器件选择(ESD，Filter）及走线注意事项的详细说明。2 Power management 2.1 SMPS 2.1.1 Components specification 2.1.2 Input power supply selection 92.1.3 Minimize SMPS EMI emissions 2.1.4 Internal LDOs and digital core decoupling 2.1.5 Powering external components 2.2 Charger 2.2.1 Charger connections.2.2.2 General charger operation2.2.3 Temperature measurement during charging 2.3 SYS_CTRL 3 Bluetooth radio3.1 RF PSU component choice 3.2 RF band-pass filter3.3 Layout (天线 走线的注意事项)4 Audio4.1 Audio bypass capacitors 4.2 Earphone speaker output4.3 Line/Mic input 4.4 Headphone output optimizition5 LED pads 5.1 LED driver 5.2 Digital/Button input 5.3 Analog input5.4 Disabled 6 Reset pin (Reset#)7 USB interfaces7.1 USB device port7.1.1 USB device port7.1.2 Layout notes 7.1.3 USB charger detectionA QCC5144 VFBGA example schematic and BOM B Recommended SMPS components specificationB.1 Inductor specifition B.2 Recommended inductors B.3 SMPS capacitor specifition
上传时间： 2022-04-07
上传用户：默默
介绍一种万能模拟信号输入采集电路,可以同时支持电压、电流、热电偶、热电阻等常见的工业类型信号,方便后级电路的测量。该研究成果通过不断优化和完善,已成功应用到了中控仪表的新产品中。The paper introduces a collection circuit of universal signal input. The circuit support voltage, current, thermocouple, thermal resistance and other common industrial type signal. The research results, which has been continuous optimized and improved, has been successfully applied to the new production of Zhejiang Supcon Instrument Co., Ltd.
标签： 采集电路
上传时间： 2022-04-21
上传用户：slq1234567890
如果在调谐器或电视机附近使用本机或任何其他使用微处理器的电子设备，则可能会产生图像的噪声或干扰。如果发生这种情况，请采取以下步骤将本机安装在尽可能远离调谐器或T的地方。远离调谐器或T，远离本机的电源线和输入/输出连接电缆。尤其在使用室内天线或300欧姆馈线。我们建议使用室外天线和75 Q / ohm同轴电缆Noise or disturbance of the picture may be generated if this unit or any other electronic equipment using microprocessors is used near a tuner or TV If this happens, take the following stepsInstall this unit as far away as possible from the tuner or T Run the antenna wires from the tuner or T away from this unit ' s power supply cord and input/output connection cables. Noise or disturbance tends to occur particularly when using indoor antennas or300 ohm feeder wires. We recommend using outdoor antennas and 75 Q/ohm coaxial cables
标签： 功放
上传时间： 2022-04-22
上传用户：
超声波换能器作为一种实用的检测手段，能实现声波所携带的信息和电能之间转换。它的性能优良，价格低廉，操作方便，易于调试，因此在工农业生产中发挥着重要的作用。但目前换能器驱动电路的发射频率多为40 kHz，本文针对1 MHz的超声波换能器电路进行了设计，主要介绍了它的发射驱动电路和接收驱动电路的设计方案，并对它们的功能进行了详细地说明。最后搭建实验平台，并对电路的输入、输出模块进行了测试。实验结果表明，换能器电路运行良好，可以为超声波高精度测量领域的应用提供参考。As a practical means of detection, ultrasonic transducer can realize the conversion between theinformation carried by sound wave and electric energy.It has the advantages of excellent performance,low cost, convenient operation and debugging, so plays an important role in industrial and agriculturalproduction.However, the transmitting frequency of the driving circuit for most transducer is 40 kHz.Thecircuit of 1 MHz ultrasonic transducer is designed In this paper. It mainly introduces the emissive drivingcircuit and the receiving circuit design and the detailed function of them. Finally, the experimentalplatform is built, and the circuit of input and output were tested. Experiments show that the transducer＇ s...
上传时间： 2022-04-28
上传用户：
数字频率计是电工电子中常用的测量仪器,数字频率计通过用输入待测信号对一特定长度的信号进行计数,从而得出频率并通过数码管直观的显示出来。本文提出了一种与输入同步的数字频率计的设计,提高了频率计的精度,设计采用Multisim软件进行设计和仿真的过程,介绍了其工作原理,硬件电路设计和仿真的过程。设计采用了Multisim软件进行设计和仿真,设计结果得到的验证。Digital frequency counter is used to measure the frequency of a signal.It is common to use a multivibrator to generate a standard 1 second time base signal and count input signal gated by this signal.However,the asynchronous of this time base signal with input signal will bring errors.In this paper,a high precision frequency counter which use synchronized time base signal generator is proposed.This frequency counter is designed and simulated by Multisim tools and result is verified.
标签： multisim
上传时间： 2022-05-08
上传用户：
CH7525 is a low-cost, low-power semiconductor device that translates the DisplayPort signal to HDMI/DVI. This innovative DisplayPort receiver with an integrated HDMI Transmitter is specially designed to target the notebook/ultrabook, tablet device and PC market segments. Through the CH7525’s advanced decoding / encoding algorithm, the input DisplayPort high-speed serialized multimedia data can be seamlessly converted to HDMI/DVI output.
上传时间： 2022-06-02
上传用户：
ATS2819/ATS2819P标准应用方案主要分为以下功能模块：Power Supply，BlueTooth，Audio Input/Output（包括codec、I2C、SPDIF），FM Receiver，disaplay（LED&LCD），USB，SPI NOR Flash Memory，SD/MMC/MS Card等。1.2原理图设计总体原则1原理图设计需要按照方案规格的要求实现各项硬件功能，尽量避免功能模块相互间的资源冲突。如果存在I/O复用，接收复用等情况，除了需注意检查I/O上电状态，接口时序等，还需要注意复用的SIO工作频率与工作电压域是否符合要求(如WIO)，确保功能设计正确实现。2原理图设计要求性能达到要求。如稳定性，启动电压，功耗，ESD，EMI等。要注意检查模块电源开关状态，选择的原件标称及精度、材质，接口保护元件和EMI滤波器等。3系统时钟26MHZ，要求CL为7~9PF，精度为+-10PPM。这样才能保证系统能正常工作。4当设计PCB受限于模具大小时，各个模块无法保证均能得到最优的布局布线(如滤波电容要求靠近IC、走线上要求尽量少的过孔与尽可能短的走线)。因为在此给出一个模块优先级以供设计人员参考，从而提高方案设计的效率，增加一版work的可行性。将优先级以阿拉伯数据排列
上传时间： 2022-06-07
上传用户：
ICN6201/02 is a bridge chip which receives MIPI® DSI inputs and sends LVDS outputs. MIPI® DSI supports up to 4 lanes and each lane operates at 1Gbps maximum; the totally maximum input bandwidth is 4Gbps; and the MIPI defined ULPS(ultra-low-power state) is also supported. ICN6201 decodes MIPI® DSI 18bepp RGB666 and 24bpp RGB888 packets.The LVDS output 18 or 24 bits pixel with 25MHz to 154MHz, by VESA or JEIDA format.ICN6201/02 support video resolution up to FHD (1920x1080) and WUXGA (1920x1200).ICN6201 adopts QFN48 package and ICN6202 adopts QFN40 package
标签： icn6202
上传时间： 2022-06-10
上传用户：kingwide
【例3.1]4位全加器module adder 4（cout，sum i na，i nb，cin）；output[3：0]sum output cout；input[3：0]i na，i nb；input cin；assign（cout，suml=i na +i nb+ci n；endmodule【例3.2]4位计数器module count 4（out，reset，clk）；output[3：0]out；input reset，cl k；regl 3：01 out；always@posedge clk）
标签： verilog
上传时间： 2022-06-16
上传用户：canderile
說明：1，测试交流电源（Test AC Power Supply）：A.中国（China）：AC 220V+/-2%50Hz+/-2%B.美国（United States of America）：AC 120V+/-2%60Hz+/-2%。C.英国（Britain）：AC 240V+/-2%50Hz+/-2%D.欧洲（Europe）：AC 230V+/-2%50Hz+/-2%E.日本（Japan）：AC 100V+/-2%60Hz+/-2%F.墨西哥（Mexico）：AC 127V+/-2%60Hz+/-2%2，测试温度条件（Test Temperature Conditions）：25℃+/-2℃。3，测试以右声道为准（Standard Test Use Right Channell）4，信号由AUX插座输入（Signal From AUX Jack Input）。5，测试以音量最大，音调和平衡在中央位置（电子音调在正常状态）。（Test Volume Setup Max，Equalizer And Balance Setup Center）。6，标准輸出（Standard Output）：A.输入1 KHz频率信号（Input 1 KHz Frequency Signal）B.左右声道输入信号测试右声道（L&R Input Signal Test Use R Channel）C.额定输出功率満（Rating Output Power Full）10 W，标准输出定为1w.（Rating Output Power Full 10 w，Standard Output Setup 1 W）D.额定输出功率1W到10w，标准输出定为500 mW（Rating Output Power 1 W To 10 W，Standard Output Setup 500 mW）E.额定输出功率小于1w，标准输出定为50 mW（Rating Output Power Not Full 1 W，Standard Output Setup 50 mW）F.标准輸出电压以V-VPR为准（Standard Output Voltage Use V-V/PR）。G.V-V/PR中P为额定输出功率，R为喇叭标称阻抗。
标签： 音响功放
上传时间： 2022-06-18
上传用户：
