虫虫首页| 资源下载| 资源专辑| 精品软件
登录| 注册

Pci-to-<b>Pci</b>

  • 现色彩空间转换R’G’B’ to Y’CbCr的VHDL源代码。

    现色彩空间转换R’G’B’ to Y’CbCr的VHDL源代码。

    标签: CbCr VHDL to 色彩

    上传时间: 2016-10-15

    上传用户:cazjing

  • PEX 8311 ExpressLane PCI Express-to-Generic Local Bus Bridge Data Book

    PEX 8311 ExpressLane PCI Express-to-Generic Local Bus Bridge Data Book

    标签: Express-to-Generic ExpressLane Bridge Local

    上传时间: 2016-12-27

    上传用户:zm7516678

  • PEX 8111BB ExpressLane PCI Express-to-PCI Bridge Data Book Version 1.2

    PEX 8111BB ExpressLane PCI Express-to-PCI Bridge Data Book Version 1.2

    标签: Express-to-PCI ExpressLane Version Bridge

    上传时间: 2014-11-26

    上传用户:lanwei

  • 采用FPGA实现色彩空间转换R’G’B’ to Y’CbCr的VHDL和verilog源代码,支持xilinx的各种器件.

    采用FPGA实现色彩空间转换R’G’B’ to Y’CbCr的VHDL和verilog源代码,支持xilinx的各种器件.

    标签: verilog xilinx FPGA CbCr

    上传时间: 2013-12-12

    上传用户:lps11188

  • usb pci detection to usb port device

    usb pci detection to usb port device

    标签: usb detection device port

    上传时间: 2014-11-18

    上传用户:zhoujunzhen

  • Run RGB Video and watch the R-G-B Video Components parralel to the original Video

    Run RGB Video and watch the R-G-B Video Components parralel to the original Video

    标签: Video Components the parralel

    上传时间: 2017-05-07

    上传用户:xmsmh

  • how to finding the best way from A to B

    how to finding the best way from A to B

    标签: finding best from to

    上传时间: 2013-12-19

    上传用户:zhouli

  • To use this function just define a variable say var, var = pnseq(a, b, c) for a, b and c refe

    To use this function just define a variable say var, var = pnseq(a, b, c) for a, b and c refer to the zip file

    标签: var function variable define

    上传时间: 2014-01-06

    上传用户:zhuoying119

  • 基于FPGA的PCI接口的设计

    PCI(Peripheral Component Interconnect)局部总线是微型计算机中处理器、存储器与外围控制部件、扩展卡之间的互连接口,由于其速度快、可靠性高、成本低、兼容性好等特点,在各种计算机总线标准占有重要地位,基于PCI标准的接口设计已经成为相关项目开发中的一个重要的选择。    目前,现场可编程门阵列FPGA(Field Programmable Gates)得到了广泛应用。由于其具有规模大,开发过程投资小,可反复编程,且支持软硬件协同设计等特点,因此已逐步成为复杂数字硬件电路设计的首选。    PCI接口的开发有多种方法,主要有两种:一是使用专用接口芯片,二是使用可编程逻辑器件,如FPGA。本论文基于成本和实际需要的考虑,采用第二种方法进行设计。    本论文采用自上而下(Top-To-Down)和模块化的设计方法,使用FPGA和硬件描述语言(VHDL和Verilog HDL)设计了一个PCI接口核,并通过自行设计的试验板对其进行验证。为使设计准确可靠,在具体模块的设计中广泛采用流水线技术和状态机的方法。    论文最终设计完成了一个33M32位的PCI主从接口,并把它作为以NIOSⅡ为核心的SOPC片内外设,与通用计算机成功进行了通讯。    论文对PCI接口进行了功能仿真,仿真结果和PCI协议的要求一致,表明本论文设计正确。把设计下载进FPGA芯片EP2C8Q208C7之后,论文给出了使用SIGNALTAPⅡ观察到的信号实际波形,波形显示PCI接口能够满足本设计中系统的需要。本文最后还给出试验板的具体设计步骤及驱动程序的安装。

    标签: FPGA PCI 接口的设计

    上传时间: 2013-07-28

    上传用户:372825274

  • PCI ExpressTM Architecture

    PCI ExpressTM Architecture Add-in Card Compliance Checklist for the PCI Express Base 1.0a SpecificationThe PCI Special Interest Group disclaims all warranties and liability for the use of this document and the information contained herein and assumes no responsibility for any errors that may appear in this document, nor does the PCI Special Interest Group make a commitment to update the information contained herein.Contact the PCI Special Interest Group office to obtain the latest revision of this checklistQuestions regarding the ths document or membership in the PCI Special Interest Group may be forwarded tPCI Special Interest Group5440 SW Westgate Drive #217Portland, OR 97221Phone: 503-291-2569Fax: 503-297-1090 DISCLAIMERThis document is provided "as is" with no warranties whatsoever, including any warranty of merchantability, noninfringement, fitness for any particular purpose, or any warranty otherwise arising out of any proposal, specification, or sample.  The PCI SIG disclaims all liability for infringement of proprietary rights, relating to use of information in this specification.  No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted herein.

    标签: Architecture ExpressTM PCI

    上传时间: 2013-11-03

    上传用户:gy592333