The PW2163 is a high efficiency 500 kHz synchronous step-down DC-DC converter capable ofdelivering 3A current. The PW2163 operates over a wide input voltage range from 4.5V to 18V andintegrates main switch and synchronous switch with very low RDS(ON) to minimize the conductionloss. Low output voltage ripple and small external inductor and capacitor sizes are achieved with 500kHz switching frequency. It adopts the instant PWM architecture to achieve fast transient responsesfor high step down applications
标签： pw2163
上传时间： 2022-02-11
上传用户：
The PW2162 is a fully integrated, high– efficiency 2A synchronous rectified step-down converter.The PW2162 operates at high efficiency over a wide output current load range. This device offerstwo operation modes, PWM control and PFM Mode switching control, which allows a high efficiencyover the wider range of the load. The PW2162 requires a minimum number of readily availablestandard external components and is available in an 6-pin SOT23 ROHS compliant package.
标签： pw2162
上传时间： 2022-02-11
上传用户：d1997wayne
The PW2053 is a high-efficiency monolithic synchronous buck regulator using a constantfrequency, current mode architecture. The device is available in an adjustable version. Supply currentwith no load is 40uA and drops to <1uA in shutdown. The 2.5V to 5.5V input voltage range makesthe PW2053 ideally suited for single Li-Ion battery powered applications. 100% duty cycle provideslow dropout operation, extending battery life in portable systems. PWM/PFM mode operationprovides very low output ripple voltage for noise sensitive applications. Switching frequency isinternally set at 1.2MHz, allowing the use of small surface mount inductors and capacitors. Lowoutput voltages are easily supported with the 0.6V feedback reference voltage
标签： pw2053
上传时间： 2022-02-14
上传用户：jason_vip1
PW1555 is a programmable current limit switch with input voltage range selection and outputvoltage clamping. Extremely low RDS(ON) of the integrated protection N-channel FET helps toreduce power loss during the normal operation. Programmable soft-start time controls the slew rateof the output voltage during the start-up time. Independent enable control allows the complicatedsystem sequencing control. It integrates the over-temperature protection shutdown andautorecovery with hystersis
标签： pw1555
上传时间： 2022-02-14
上传用户：
The PW8205A6S uses advanced trench technology to provide excellent RDS(ON), low gate chargeand operation with gate voltages as low as 2.5V. This device is suitable for use as a Battery protectionor in other Switching application.
标签： 8205a6
上传时间： 2022-02-14
上传用户：
该问题由某客户提出，发生在 STM32F207VET6 器件上。据其工程师讲述：部分芯片无法通过拉低NRST PIN产生复位。该现象一旦上电复位后无法重现。客户的应用中通过外部硬件看门狗定时给NRST PIN送低电平产生复位。正常情况下，MCU会给外部硬件看门狗喂狗。
上传时间： 2022-02-21
上传用户：
ADC模数转换器件Altium Designer AD原理图库元件库SV text has been written to file : 4.4 - ADC模数转换器件.csvLibrary Component Count : 29Name Description----------------------------------------------------------------------------------------------------ADC0800 National 8-Bit Analog to Digital ConverterADC0809 ADC0831 ADCADC0832 ADC8 Generic 8-Bit A/D ConverterCLC532 High-Speed 2:1 Analog MultiplexerCS5511 National 16-Bit Analog to Digital ConverterDAC8 Generic 8-Bit D/A ConverterEL1501 Differential line Driver/ReceiverEL2082 Current-Mode MultiplierEL4083 Current Mode Four Quadrant MultiplierEL4089 DC Restored Video AmplifierEL4094 Video Gain Control/FaderEL4095 Video Gain Contol/Fader/MultiplexerICL7106 LMC6953_NSC PCI Local Bus Power SupervisorMAX4147 300MHz, Low-Power, High-Output-Current, Differential Line DriverMAX4158 350MHz 2-Channel Video Multiplexer-AmplifierMAX4159 350MHz 2-Channel Video Multiplexer-AmplifierMAX4258 250MHz, 2-Channel Video Multiplexer-AmplifierMAX4259 250MHz 2-Channel Video Multiplexer-AmplifierMAX951 Ultra-Low-Power, Single-Supply Op Amp + Comparator + ReferenceMAX952 Ultra-Low-Power, Single-Supply Op Amp + Comparator + ReferenceMC1496 Balanced Modulator/DemodulatorPLL100k Generic Phase Locked LoopPLL10k Generic Phase Locked LoopPLL5k Generic Phase Locked LoopPLLx Generic Phase Locked Loop水位计
标签： adc 模数转换 altium designer
上传时间： 2022-03-13
上传用户：
CH341系列编程器芯片usb转串口Altium Designer AD原理图库元件库CSV text has been written to file : 1.9 - CH341系列编程器芯片.csvLibrary Component Count : 56Name Description----------------------------------------------------------------------------------------------------CH311Q PC debug port monitorCH331T Mini USB Disk ControllerCH340G CH340H USB to TTL Serial / UART, USB to IrDACH340T USB to TTL Serial / UART, USB to IrDACH340R USB to IrDA, USB to RS232 SerialCH340S_P USB to Print Port / ParallelCH340S_S USB to TTL Serial / UART, pin compatible with CH341CH341A_S USB to TTL Serial / UART / I2C/IICCH341S_P USB to Print Port / ParallelCH341A_P USB to Print Port / ParallelCH341S_S USB to TTL Serial / UARTCH341S_X USB to EPP Parallel / SPI / I2C/IICCH341A_X USB to EPP Parallel / SPI / I2C/IICCH341T USB to TTL Serial / UART / I2C/IICCH345T USB to MidiCH352L_M PCI to 8255 mode 2 Parallel for MCU and 16C550 UART / IrDACH352L_P PCI to Print Port / Parallel and 16C550 UART / IrDACH352L_S PCI to Dual 16C550 UART, TTL Serial*2 / IrDA*1CH362L PCI Device / Slave only for RAM / Expansion ROMCH364F Member of CH364 chipsetsCH364P PCI Device / Slave Embedded Flash ROM, for Expansion ROMCH365P PCI Device / Slave, for I/O port or RAM / ROMCH372T USB Device / Slave for MCU, ParallelCH372A USB Device / Slave for MCU, ParallelCH372V USB Device / Slave for MCU, ParallelCH374S USB Host & Device / Slave for MCU, parallel / SPICH374T USB Host & Device / Slave for MCU, parallel / SPICH375S USB Host & Device / Slave for MCU, parallel / UART SerialCH375A USB Host & Device / Slave for MCU, parallel / UART SerialCH375V USB Host & Device / Slave for MCU, parallel / UART SerialCH411G FDC MFM encode and decodeCH421A Dual port bufferCH421S Dual port bufferCH423D I2C/IIC I/O expander, 16 GPO + 8 GPIO, 128 LEDs DriveCH423S I2C/IIC I/O expander, 16 GPO + 8 GPIO, 128 LEDs DriveCH423D_D I2C/IIC I/O expander, 16 GPO + 8 GPIO, 128 LEDs DriveCH423S_D I2C/IIC I/O expander, 16 GPO + 8 GPIO, 128 LEDs DriveCH423G I2C/IIC I/O expander, 6 GPO + 5 GPIOCH432Q Dual 16C550 UART with IrDA, parallel / SPICH432T SPI Dual 16C550 UART with IrDACH450K 6 Digits / 48 LEDs Drive & 8x6 Keyboard, I2C/IICCH450H 6 Digits / 48 LEDs Drive & 8x6 Keyboard, I2C/IICCH450L 8 Digits / 64 LEDs Drive & 8x8 Keyboard, I2C/IICCH451L 8 Digits / 64 LEDs Drive & 8x8 Keyboard, 4 Wire Interface, SPICH451S 8 Digits / 64 LEDs Drive & 8x8 Keyboard, 4 Wire Interface, SPICH451D 8 Digits / 64 LEDs Drive & 8x8 Keyboard, 4 Wire Interface, SPICH452L_2 8 Digits / 64 LEDs Drive & 8x8 Keyboard, I2C/IICCH452L_4 8 Digits / 64 LEDs Drive & 8x8 Keyboard, 4 Wire Interface, SPICH452S_2 8 Digits / 64 LEDs Drive & 8x8 Keyboard, I2C/IICCH452S_4 8 Digits / 64 LEDs Drive & 8x8 Keyboard, 4 Wire Interface, SPICH453S 16 Digits / 128 LEDs Drive, I2C/IICCH453D 16 Digits / 128 LEDs Drive, I2C/IICPCI 32Bit PCI Bus, simple / short cardPCI32 32Bit PCI BusUSB USB Port
标签： ch341 编程芯片 usb 串口 altium designer
上传时间： 2022-03-13
上传用户：
电子书-RTL Design Style Guide for Verilog HDL540页A FF having a fixed input value is generated from the description in the upper portion of Example 2-21. In this case, ’0’ is output when the reset signal is asynchronously input, and ’1’ is output when the START signal rises. Therefore, the FF data input is fixed at the power supply, since the typical value ’1’ is output following the rise of the START signal. When FF input values are fixed, the fixed inputs become untestable and the fault detection rate drops. When implementing a scan design and converting to a scan FF, the scan may not be executed properl not be executed properly, so such descriptions , so such descriptions are not are not recommended. recommended.[1] As in the lower part of Example 2-21, be sure to construct a synchronous type of circuit and ensure that the clock signal is input to the clock pin of the FF. Other than the sample shown in Example 2-21, there are situations where for certain control signals, those that had been switched due to the conditions of an external input will no longer need to be switched, leaving only a FF. If logic exists in a lower level and a fixed value is input from an upper level, the input value of the FF may also end up being fixed as the result of optimization with logic synthesis tools. In a situation like this, while perhaps difficult to completely eliminate, the problem should be avoided as much as possible.
标签： RTL verilog hdl
上传时间： 2022-03-21
上传用户：canderile
产品型号：VKD223EB 产品品牌：VINKA/永嘉微电 封装形式：SOT23-6 产品年份：新年份 联 系 人：陈锐鸿 Q Q：361 888 5898 联系手机：188 2466 2436（信） 概 述 VKD223EB VinTouchTM 是单按键触摸检测芯片, 稳定的触摸检测效果可以广泛的满足不同应用的需求, 此触摸检测芯片是专为取代传统按键而设计, 触摸检测 PAD 的大小可依不同的灵敏度设计在合理的范围内, 低功耗与宽工作电压, 是此触摸芯片在 DC或AC应用上的特性。 特 点 � 工作电压 2.0V ~ 5.5V � 工作电流 @VDD=3V﹐无负载 低功耗模式下典型值 2.0uA､最大值 4.0uA � 最长回应时间大约为低功耗模式 220ms @VDD=3V � 可以由外部电容 (1~50pF) 调整灵敏度 � 稳定的人体触摸检测可取代传统的按键开关 � 提供低功耗模式 � 提供输出模式选择 (TOG pin) 可选择直接输出或锁存 (toggle) 输出 � Q pin 为 CMOS 输出﹐可由 (AHLB pin) 选择高电平输出有效或低电平输出有效 � 上电后约有 0.5 秒的稳定时间﹐此期间内不要触摸检测点﹐此时所有功能都被禁止 � 自动校准功能 刚上电的 8 秒内约每 1 秒刷新一次参考值﹐若在上电后的 8 秒内有触摸按键或 8 秒后仍未触摸按键，则重新校准周期切换为 4 秒 应用范围 � 各种消费性产品 � 取代按钮按键 标准触控IC-电池供电系列： VKD223EB --- 工作电压/电流：2.0V-5.5V/5uA-3V 感应通道数：1 通讯界面 最长回应时间快速模式60mS，低功耗模式220ms 封装：SOT23-6 VKD223B --- 工作电压/电流：2.0V-5.5V/5uA-3V 感应通道数：1 通讯界面 最长回应时间快速模式60mS，低功耗模式220ms 封装：SOT23-6 VKD233DB --- 工作电压/电流：2.4V-5.5V/2.5uA-3V 1感应按键 封装：SOT23-6 通讯界面：直接输出，锁存(toggle)输出 低功耗模式电流2.5uA-3V VKD233DH ---工作电压/电流：2.4V-5.5V/2.5uA-3V 1感应按键 封装：SOT23-6 通讯界面：直接输出，锁存(toggle)输出 有效键最长时间检测16S VKD233DS --- 工作电压/电流：2.4V-5.5V/2.5uA-3V 1感应按键 封装：DFN6（2*2超小封装） 通讯界面：直接输出，锁存(toggle)输出 低功耗模式电流2.5uA-3V VKD233DR --- 工作电压/电流：2.4V-5.5V/1.5uA-3V 1感应按键 封装：DFN6（2*2超小封装） 通讯界面：直接输出，锁存(toggle)输出 低功耗模式电流1.5uA-3V VKD233DG --- 工作电压/电流：2.4V-5.5V/2.5uA-3V 1感应按键 封装：DFN6（2*2超小封装） 通讯界面：直接输出，锁存(toggle)输出 低功耗模式电流2.5uA-3V VKD233DQ --- 工作电压/电流：2.4V-5.5V/5uA-3V 1感应按键 封装：SOT23-6 通讯界面：直接输出，锁存(toggle)输出 低功耗模式电流5uA-3V VKD233DM --- 工作电压/电流：2.4V-5.5V/5uA-3V 1感应按键 封装：SOT23-6 （开漏输出） 通讯界面：开漏输出，锁存(toggle)输出 低功耗模式电流5uA-3V VKD232C --- 工作电压/电流：2.4V-5.5V/2.5uA-3V 感应通道数：2 封装：SOT23-6 通讯界面：直接输出，低电平有效 固定为多键输出模式，内建稳压电路 MTP触摸IC——VK36N系列抗电源辐射及手机干扰： VK3601L --- 工作电压/电流：2.4V-5.5V/4UA-3V3 感应通道数：1 1对1直接输出 待机电流小，抗电源及手机干扰，可通过CAP调节灵敏 封装：SOT23-6 VK36N1D --- 工作电压/电流：2.2V-5.5V/7UA-3V3 感应通道数：1 1对1直接输出 触摸积水仍可操作，抗电源及手机干扰，可通过CAP调节灵敏封装：SOT23-6 VK36N2P --- 工作电压/电流：2.2V-5.5V/7UA-3V3 感应通道数：2 脉冲输出 触摸积水仍可操作，抗电源及手机干扰，可通过CAP调节灵敏封装：SOT23-6 VK3602XS ---工作电压/电流：2.4V-5.5V/60UA-3V 感应通道数：2 2对2锁存输出 低功耗模式电流8uA-3V，抗电源辐射干扰，宽供电电压 封装：SOP8 VK3602K --- 工作电压/电流：2.4V-5.5V/60UA-3V 感应通道数：2 2对2直接输出 低功耗模式电流8uA-3V，抗电源辐射干扰，宽供电电压 封装：SOP8 VK36N2D --- 工作电压/电流：2.2V-5.5V/7UA-3V3 感应通道数：2 1对1直接输出 触摸积水仍可操作，抗电源及手机干扰，可通过CAP调节灵敏封装：SOP8 VK36N3BT ---工作电压/电流：2.2V-5.5V/7UA-3V3 感应通道数：3 BCD码锁存输出 触摸积水仍可操作，抗电源及手机干扰，可通过CAP调节灵敏 封装：SOP8 VK36N3BD ---工作电压/电流：2.2V-5.5V/7UA-3V3 感应通道数：3 BCD码直接输出 触摸积水仍可操作，抗电源及手机干扰，可通过CAP调节灵敏 封装：SOP8 VK36N3BO ---工作电压/电流：2.2V-5.5V/7UA-3V3 感应通道数：3 BCD码开漏输出 触摸积水仍可操作，抗电源及手机干扰 封装：SOP8/DFN8（超小超薄体积） VK36N3D --- 工作电压/电流：2.2V-5.5V/7UA-3V3 感应通道数：3 1对1直接输出 触摸积水仍可操作，抗电源及手机干扰 封装：SOP16/DFN16（超小超薄体积） VK36N4B ---工作电压/电流：2.2V-5.5V/7UA-3V3 感应通道数：4 BCD输出 触摸积水仍可操作，抗电源及手机干扰 封装：SOP16/DFN16（超小超薄体积） VK36N4I---工作电压/电流：2.2V-5.5V/7UA-3V3 感应通道数：4 I2C输出 触摸积水仍可操作，抗电源及手机干扰 封装：SOP16/DFN16（超小超薄体积） VK36N5D ---工作电压/电流：2.2V-5.5V/7UA-3V3 感应通道数：5 1对1直接输出 触摸积水仍可操作，抗电源及手机干扰 封装：SOP16/DFN16（超小超薄体积） VK36N5B ---工作电压/电流：2.2V-5.5V/7UA-3V3 感应通道数：5 BCD输出 触摸积水仍可操作，抗电源及手机干扰 封装：SOP16/DFN16（超小超薄体积） VK36N5I ---工作电压/电流：2.2V-5.5V/7UA-3V3 感应通道数：5 I2C输出 触摸积水仍可操作，抗电源及手机干扰 封装：SOP16/DFN16（超小超薄体积） VK36N6D --- 工作电压/电流：2.2V-5.5V/7UA-3V3 感应通道数：6 1对1直接输出 触摸积水仍可操作，抗电源及手机干扰 封装：SOP16/DFN16（超小超薄体积） VK36N6B ---工作电压/电流：2.2V-5.5V/7UA-3V3 感应通道数：6 BCD输出 触摸积水仍可操作，抗电源及手机干扰 封装：SOP16/DFN16（超小超薄体积） VK36N6I ---工作电压/电流：2.2V-5.5V/7UA-3V3 感应通道数：6 I2C输出 触摸积水仍可操作，抗电源及手机干扰 封装：SOP16/DFN16（超小超薄体积） VK36N7B ---工作电压/电流：2.2V-5.5V/7UA-3V3 感应通道数：7 BCD输出 触摸积水仍可操作，抗电源及手机干扰 封装：SOP16/DFN16（超小超薄体积） VK36N7I ---工作电压/电流：2.2V-5.5V/7UA-3V3 感应通道数：7 I2C输出 触摸积水仍可操作，抗电源及手机干扰 封装：SOP16/DFN16（超小超薄体积） VK36N8B ---工作电压/电流：2.2V-5.5V/7UA-3V3 感应通道数：8 BCD输出 触摸积水仍可操作，抗电源及手机干扰 封装：SOP16/DFN16（超小超薄体积） VK36N8I ---工作电压/电流：2.2V-5.5V/7UA-3V3 感应通道数：8 I2C输出 触摸积水仍可操作，抗电源及手机干扰 封装：SOP16/DFN16（超小超薄体积） VK36N9I ---工作电压/电流：2.2V-5.5V/7UA-3V3 感应通道数：9 I2C输出 触摸积水仍可操作，抗电源及手机干扰 封装：SOP16/DFN16（超小超薄体积） VK36N10I ---工作电压/电流：2.2V-5.5V/7UA-3V3 感应通道数：10 I2C输出 触摸积水仍可操作，抗电源及手机干扰 封装：SOP16/DFN16（超小超薄体积） 注：具体参数以最新PDF为准,型号众多未能一一介绍，欢迎索取PDF/样品KPP558
标签： TWS 223 VKD IC EB 应用于 小米 充电器 单键 耳机
上传时间： 2022-03-21
上传用户：shubashushi66
