Agilent 34401A Service Guide.pdfIEC Measurement Category II includes electrical devices connected to mains at an outlet on a branch circuit. Such devices include most small appliances, test equipment, and other devices that plug into a branch outlet or socket. The 34401A may be used to make measurements with the HI and LO inputs connected to mains in such devices, or to the branch outlet itself (up to 300 VAC). However, the 34401A may not be used with its HI and LO inputs connected to mains in permanently installed electrical devices such as the main circuit-breaker panel, sub-panel disconnect boxes, or permanently wired motors. Such devices and circuits are subject to overvoltages that may exceed the protection limits of the 34401A. Note: Voltages above 300 VAC may be measured only in circuits that are isolated from mains. However, transient overvoltages are also present on circuits that are isolated from mains. The Agilent 34401A are designed to safely withstand occasional transient overvoltages up to 2500 Vpk. Do not use this equipment to measure circuits where transient overvoltages could exceed this level. Additional Notices Waste Electrical and Electronic Equipment (WEEE) Directive 2002/96/EC This product complies with the WEEE Directive (2002/96/EC) marking requirement. The affixed product label (see below) indicates that you must not discard this electrical/electronic product in domestic household waste. Product Category: With reference to the equipment types in the WEEE directive Annex 1, this product is classified as a "Monitoring and Control instrumentation" product. Do not dispose in domestic household waste. To return unwanted products, contact your local Agilent office, or see www.agilent.com/environment/product for more information. Agilent 34138A Test Lead Set The Agilent 34401A is compatible with the Agilent 34138A Test Lead Set described below. Test Lead Ratings Test Leads - 1000V, 15A Fine Tip Probe Attachments - 300V, 3A Mini Grabber Attachment - 300V, 3A SMT Grabber Attachments - 300V, 3A Operation The Fine Tip, Mini Grabber, and SMT Grabber attachments plug onto the probe end of the Test Leads. Maintenance If any portion of the Test Lead Set is worn or damaged, do not use. Replace with a new Agilent 3413
标签： agilent
上传时间： 2022-02-20
上传用户：
ADC模数转换器件Altium Designer AD原理图库元件库SV text has been written to file : 4.4 - ADC模数转换器件.csvLibrary Component Count : 29Name Description----------------------------------------------------------------------------------------------------ADC0800 National 8-Bit Analog to Digital ConverterADC0809 ADC0831 ADCADC0832 ADC8 Generic 8-Bit A/D ConverterCLC532 High-Speed 2:1 Analog MultiplexerCS5511 National 16-Bit Analog to Digital ConverterDAC8 Generic 8-Bit D/A ConverterEL1501 Differential line Driver/ReceiverEL2082 Current-Mode MultiplierEL4083 Current Mode Four Quadrant MultiplierEL4089 DC Restored Video AmplifierEL4094 Video Gain Control/FaderEL4095 Video Gain Contol/Fader/MultiplexerICL7106 LMC6953_NSC PCI Local Bus Power SupervisorMAX4147 300MHz, Low-Power, High-Output-Current, Differential Line DriverMAX4158 350MHz 2-Channel Video Multiplexer-AmplifierMAX4159 350MHz 2-Channel Video Multiplexer-AmplifierMAX4258 250MHz, 2-Channel Video Multiplexer-AmplifierMAX4259 250MHz 2-Channel Video Multiplexer-AmplifierMAX951 Ultra-Low-Power, Single-Supply Op Amp + Comparator + ReferenceMAX952 Ultra-Low-Power, Single-Supply Op Amp + Comparator + ReferenceMC1496 Balanced Modulator/DemodulatorPLL100k Generic Phase Locked LoopPLL10k Generic Phase Locked LoopPLL5k Generic Phase Locked LoopPLLx Generic Phase Locked Loop水位计
标签： adc 模数转换 altium designer
上传时间： 2022-03-13
上传用户：
电子书-RTL Design Style Guide for Verilog HDL540页A FF having a fixed input value is generated from the description in the upper portion of Example 2-21. In this case, ’0’ is output when the reset signal is asynchronously input, and ’1’ is output when the START signal rises. Therefore, the FF data input is fixed at the power supply, since the typical value ’1’ is output following the rise of the START signal. When FF input values are fixed, the fixed inputs become untestable and the fault detection rate drops. When implementing a scan design and converting to a scan FF, the scan may not be executed properl not be executed properly, so such descriptions , so such descriptions are not are not recommended. recommended.[1] As in the lower part of Example 2-21, be sure to construct a synchronous type of circuit and ensure that the clock signal is input to the clock pin of the FF. Other than the sample shown in Example 2-21, there are situations where for certain control signals, those that had been switched due to the conditions of an external input will no longer need to be switched, leaving only a FF. If logic exists in a lower level and a fixed value is input from an upper level, the input value of the FF may also end up being fixed as the result of optimization with logic synthesis tools. In a situation like this, while perhaps difficult to completely eliminate, the problem should be avoided as much as possible.
标签： RTL verilog hdl
上传时间： 2022-03-21
上传用户：canderile
本系统采用电动机电枢供电回路串接采样电阻的方式来实现对小型直流有刷电动机的转速测量。该系统主要由二阶低通滤波电路,小信号放大电路、单片机测量显示电路、开关稳压电源电路等组成。同时自制电机测速装置,用高频磁环作为载体,用线圈绕制磁环,利用电磁感应原理检测电机运行时的漏磁,将变化的磁场信号转化为磁环上的感应电流。用信号处理单元电路将微弱电信号转化为脉冲信号,送由单片机检测,从而达到准确测量电机的速度的要求。In this system, the sampling resistance of armature power supply circuit is connected in series to measure the speed of small DC brush motor. The system is mainly composed of second-order low-pass filter circuit, small signal amplifier circuit, single-chip measurement and display circuit, switching regulated power supply circuit and so on. At the same time, the self-made motor speed measuring device uses high frequency magnetic ring as the carrier, coil winding magnetic ring, and electromagnetic induction principle to detect the leakage of magnetic field during the operation of the motor, which converts the changed magnetic field signal into the induced current on the magnetic ring. The weak electric signal is transformed into pulse signal by signal processing unit circuit, which is sent to single chip computer for detection, so as to meet the requirement of accurate measurement of motor speed.
标签： 直流电动机
上传时间： 2022-03-26
上传用户：
随着科技发展及工业4.0 进程推进,机械臂应用范围越来越广,并演化出各种各样的机械臂,如码垛机械臂、焊接机械臂、装配机械臂以及手术机械臂等。现利用solidworks 进行三维建模,设计制作一款基于stm32f103c8t6 单片机的主从式桌面级机械臂,该机械臂包括一个主动机械臂和一个从动机械臂,采用蓝牙传输信号方式进行同步运动,并且详细介绍了该机械臂材料选择、结构设计、工作原理、组成部分和设计特点。With the development of science and technology and the advancement of Industry 4.0, the application range of the mechanical arm has become wider and wider, and various types of mechanical arms, such as palletizing robot arms, welding robot arms, assembly robot arms, and surgical robot arms, have been developed. Now using solidworks for 3D modeling, design and manufacture a master-slave desktop-level robot arm based on stm32f103c8t6 single-chip microcomputer. The robot arm includes an active robot arm and a slave robot arm, which uses Bluetooth to transmit signals for synchronous motion. The material selection, structural design, working principle, components and design features of the manipulator are introduced.
标签： stm32f103c8t6 单片机
上传时间： 2022-03-27
上传用户：
CAN总线是汽车上应用最广泛的车载网络总线,具有实时性强、可靠性高、成本低等优点。鉴于此,介绍了一种利用飞思卡尔系列单片机MC9S12XS128作为控制器,利用其内部的MSCAN模块、CAN收发器TJA1040等外围元件进行CAN总线通信节点设计。该设计能够实现CAN总线数据的发送与接收,可应用于汽车及其他各种CAN总线通信系统。CAN bus is the most widely used on-board network bus in automobiles. It has the advantages of realtime, high reliability and low cost. In view of this,this paper introduces the design of CAN bus communication node by using Freescale MC9S12XS128 as controller,using its internal MSCAN module,CAN transceiver TJA1040 and other peripheral components. This design can realize the sending and receiving of CAN bus data,and can be used in automobile and other CAN bus communication systems.
上传时间： 2022-03-27
上传用户：
数字示波器功能强大,使用方便,但是价格相对昂贵。本文以Ti的MSP430F5529为主控器,以Altera公司的EP2C5T144C8 FPGA器件为逻辑控制部件设计数字示波器。模拟信号经程控放大、整形电路后形成方波信号送至FPGA测频,根据频率值选择采用片上及片外高速AD分段采样。FPGA控制片外AD采样并将数据输入到FIFO模块中缓存,由单片机进行频谱分析。测试表明:简易示波器可以实现自动选档、多采样率采样、高精度测频及频谱分析等功能。Digital oscilloscope is powerful and easy to use, but also expensive. The research group designed a low-cost digital oscilloscope, the chip of MSP430F5529 of TI is chosen as the main controller and the device of EP2C5T144C8 of Altera company is used as the logic control unit. Analog signal enter the programmable amplifier circuit, shaping circuit and other pre-processing circuit. The shaped rectangular wave signal is sent to FPGA for measure the frequency. According to the frequency value to select AD on-chip or off-chip high-speed AD for sampling. FPGA controls the off-chip AD sampling and buffers AD data by FIFO module. The single chip microcomputer receives the data, and do FFT for spectrum analysis. The test shows that the simple oscilloscope can realize automatic gain selection, sampling at different sampling rates, high precision frequency measurement and spectrum analysis.
上传时间： 2022-03-27
上传用户：
文章提出了一种基于AT89S51单片机的智能家居系统的设计,该系统具有室内煤气以及烟雾的检测、家庭室内防盗等功能。文章详细分析了系统的总体设计,详尽分析并设计了煤气传感器模块、烟雾传感器模块、人体红外感应传感器模块、报警模块等各硬件部分,并利用PROTUES软件进行了系统仿真。仿真结果证明:系统具有成本低、效率高、操作方便等优点,达到了预期设计的效果。This paper presents the design of an intelligent home system based on AT89S51 microcontroller.The system has the functions of detecting indoor gas and smoke,guarding against theft in the home,and so on.The overall design of the system is analyzed in detail.The gas sensor module,smoke sensor module,human infrared sensor module,alarm module and other hardware parts are analyzed and designed in detail,and the system simulation is carried out using PROTUES software.The simulation results show that the system has the advantages of low cost,high efficiency,convenient operation and so on,and achieves the expected design effect.
上传时间： 2022-03-28
上传用户：
电学中的测量技术涉及范围非常广,电流测量在电学计量中占有非常重要的位置。如何精确地进行电流测量是精密测量的一大难题。传统的电流检测电路多采用运算放大芯片与片外电流检测电路相结合的方式,电路集成度很低,需要较多的接口和资源才能完成对电路的检测。本文把所有电路部分都集成在一块芯片上,包括检测电阻,运算放大器电路及模拟转数字转换电路,从而在电路内部可以进行电流检测,使电路更好的集成化。前置电路使用二级共源共栅结构的运算放大器,减小沟道长度调制效应造成的电流误差。10位SAR ADC中采用电容驱动能力强的传输门保证了模数转化器的有效精度。比较器模块采用再生锁存器与迟滞比较器作为基础单元组合解决精密测量的问题。本设计可以作为嵌入芯片内的一小部分而检测芯片中的微小电流1mA~100mA,工作电压在1.8v左右,电流检测精度预期达到10uA的需求。The measurement technology in electricity involves a wide range,and current measurement plays a very important position in electrical measurement.How to accurately measure current is a big problem in precision measurement. The traditional current detecting circuit adopts the combination of the operational amplifier chip and theoff-chip current detecting circuit, The circuit integration is very low, and more interfaces and resources are needed tocomplete the circuit detection.This topic integrates all the circuit parts into one chip, including detection resistance, operational amplifier circuit andanalog to digital conversion circuit. Highly integrated circuit makes the external resources on the chip more intensive,so that current detection can be carried out inside the circuit, so that the circuit can be better integrated. Thefront-end circuit of this project uses two-stage cascade operational amplifier and cascade tube to reduce the currenterror caused by channel length modulation effect. In 10-bit SAR ADC, the transmission gate with strong capacitivedriving ability ensures the effective accuracy of the analog-to-digital converter. Comparator module uses regenerativelatch and hysteresis comparator as basic unit to solve the difficult problem of precision measurement. This topic can beused as a small part of the embedded chip to detect the micro-current in the chip 1 mA~100 mA, the working voltageis about 1.8v, and the current detection accuracy is expected to reach the requirement of 10 uA.
上传时间： 2022-04-03
上传用户：
为设计高效率、低损耗的PFC电路,本文基于UCC28019进行电路设计。以UCC28019输出的PWM波形来控制Boost升压斩波为核心电路,使电路中的电容交替地充放电、电感交替的储存和释放能量,最后实现在输入AC20V~24V电压情况下稳定输出DC38V。测试结果表明,系统实现效率为95%左右,电压调整率小于1%,电源功率因数0.99。交流输入电压为19.0-25.8 V时,输出直流电压稳定性较好,电感无明显啸叫且纹波小,具有一定的带负载能力和实用性。In order to design the PFC circuit with high efficiency and low loss,this paper designs the circuit based on UCC28019.The PWM waveform output by UCC28019 is used to control boost chopper as the core circuit,which alternately charges and discharges capacitors,stores and releases energy by inductors,and finally achieves stable output of DC38 V under the input voltage of AC20 V~24 V.The test results show that the system achieves about 95% efficiency,the voltage adjustment rate is less than 1%,the power factor is 0.99,and the AC input voltage is 19.0-25.8 V.The output DC voltage stability is good,the inductance has no obvious whistle and the ripple is small,so it has certain load capacity and practicability.
上传时间： 2022-04-03
上传用户：
