微弱信号检测装置 四川理工学院 刘鹏飞、梁天德、曾学明 摘要： 本设计以TI的Launch Pad为核心板，采用锁相放大技术设计并制作了一套微弱信号检测装置，用以检测在强噪声背景下已知频率微弱正弦波信号的幅度值，并在液晶屏上数字显示出所测信号相应的幅度值。实验结果显示其抗干扰能力强，测量精度高。 关键词：强噪声；微弱信号；锁相放大；Launch Pad Abstract: This design is based on the Launch Pad of TI core board, using a lock-in amplifier technique designed and produced a weak signal detection device, to measure the known frequency sine wave signal amplitude values of the weak in the high noise background, and shows the measured signal amplitude of the corresponding value in the liquid crystal screen. Test results showed that it has high accuracy and strong anti-jamming capability. Keywords: weak signal detection; lock-in-amplifier; Launch Pad 1、引言 随着现代科学技术的发展，在科研与生产过程中人们越来越需要从复杂高强度的噪声中检测出有用的微弱信号，因此对微弱信号的检测成为当前科研的热点。微弱信号并不意味着信号幅度小，而是指被噪声淹没的信号，“微弱”也仅是相对于噪声而言的。只有在有效抑制噪声的条件下有选择的放大微弱信号的幅度，才能提取出有用信号。微弱信号检测技术的应用相当广泛，在生物医学、光学、电学、材料科学等相关领域显得愈发重要。 2、方案论证 针对微弱信号的检测的方法有很多，比如滤波法、取样积分器、锁相放大器等。下面就针对这几种方法做一简要说明。 方案一：滤波法。 在大部分的检测仪器中都要用到滤波方法对模拟信号进行一定的处理，例如隔离直流分量，改善信号波形，防止离散化时的波形混叠，克服噪声的不利影响，提高信噪比等。常用的噪声滤波器有：带通、带阻、高通、低通等。但是滤波方法检测信号不能用于信号频谱与噪声频谱重叠的情况，有其局限性。虽然可以对滤波器的通频带进行调节，但其噪声抑制能力有限，同时其准确性与稳定性将大打折扣。
上传时间： 2013-11-04
上传用户：lty6899826
EVAL-PRAOPAMP-2R/2RU/2RM评估板支持采用SOIC、TSSOP和MSOP封装的双运算放大器。它能以不同的应用电路和配置为用户提供多种选择和广泛的灵活性。该评估板不是为了用于高频器件或高速放大器。但是，它为用户提供了不同电路类型的多种组合，包括有源滤波器、仪表放大器、复合放大器，以及外部频率补偿电路。本应用笔记会给出几个应用电路的例子。
上传时间： 2014-12-23
上传用户：kxyw404582151
Abstract: This tutorial discusses proper printed-circuit board (PCB) grounding for mixed-signal designs. Formost applications a simple method without cuts in the ground plane allows for successful PCB layouts withthis kind of IC. We begin this document with the basics: where the current flows. Later, we describe how toplace components and route signal traces to minimize problems with crosstalk. Finally, we move on toconsider power supply-currents and end by discussing how to extend what we have learned to circuits withmultiple mixed-signal ICs.
上传时间： 2013-11-04
上传用户：pol123
Abstract: This application note presents an overview of the operational characteristics of accurate I²C real-time clocks (RTCs),including the DS3231, DS3231M, and DS3232. It focuses on general application guidelines that facilitate use of device resources forpower management, I²C communication circuit configurations, and I²C characteristics relative to device power-up sequences andinitializations. Additional discussions on decoupling are provided to support developing strategies for mitigating power-supply pushingof device frequency.
上传时间： 2013-11-23
上传用户：WMC_geophy
Abstract: A laser module designer can use a fixed resistor, mechanical pot, digital pot, or a digital-to-analogconverter (DAC) to control the laser driver's modulation and bias currents. The advantages of a programmablemethod (POT or DAC) are that the manufacturing process can be automated and digital control can be applied(e.g., to compensate for temperature). Using POTs can be a more simple approach than a DAC. There can be aslight cost advantage to using a POT, but this is usually not significant relative to other pieces of the design.Using a DAC can offer advantages, including improved linearity (translating to ease of software implementationand ability to hit the required accuracy), increased board density, a wider range of resolutions, a betteroptimization range, ease of use with a negative voltage laser driver, and unit-to-unit consistency
上传时间： 2013-11-13
上传用户：ca05991270
Who has never experienced oscillations issues when using an operational amplifier? Opampsare often used in a simple voltage follower configuration. However, this is not the bestconfiguration in terms of capacitive loading and potential risk of oscillations.Capacitive loads have a big impact on the stability of operational amplifier-basedapplications. Several compensation methods exist to stabilize a standard op-amp. Thisapplication note describes the most common ones, which can be used in most cases.The general theory of each compensation method is explained, and based on this, specific
上传时间： 2013-10-28
上传用户：chenbhdt
Digital-to-analog converters (DACs) are prevalent inindustrial control and automated test applications.General-purpose automated test equipment often requiresmany channels of precisely controlled voltagesthat span several voltage ranges. The LTC2704 is ahighly integrated 16-bit, 4-channel DAC for high-endapplications. It has a wide range of features designed toincrease performance and simplify design.
上传时间： 2013-11-22
上传用户：元宵汉堡包
MOS关模型 Cgs：由源极和沟道区域重叠的电极形成的，其电容值是由实际区域的大小和在不同工作条件下保持恒定。Cgd：是两个不同作用的结果。第一JFET区域和门电极的重叠，第二是耗尽区电容（非线性）。等效的Cgd电容是一个Vds电压的函数。Cds：也是非线性的电容，它是体二极管的结电容，也是和电压相关的。这些电容都是由Spec上面的Crss，Ciss和Coss决定的。由于Cgd同时在输入和输出，因此等效值由于Vds电压要比原来大很多，这个称为米勒效应。由于SPEC上面的值按照特定的条件下测试得到的，我们在实际应用的时候需要修改Cgd的值。
上传时间： 2013-12-09
上传用户：qlpqlq
This reference design (RD) features a fullyassembled and tested surface-mount printed circuitboard (PCB). The RD board utilizes the MAX48851:2 or 2:1 multiplexer and other ICs to implement acomplete video graphics array (VGA) 8:1multiplexer.VGA input/output connections are provided to easilyinterface the MAX4885 RD board with VGAcompatibledevices. The RD board gives the optionto use a single 5V DC power supply (V+), or this RDboard can be powered from any one of the eight VGA sources.
标签： multiplexer reference VGA
上传时间： 2013-11-09
上传用户：ANRAN
【摘要】本文结合作者多年的印制板设计经验，着重印制板的电气性能，从印制板稳定性、可靠性方面，来讨论多层印制板设计的基本要求。【关键词】印制电路板；表面贴装器件；高密度互连；通孔【Key words】Printed Circuit Board；Surface Mounting Device；High Density Interface；Via一．概述印制板（PCB－Printed Circuit Board）也叫印制电路板、印刷电路板。多层印制板，就是指两层以上的印制板，它是由几层绝缘基板上的连接导线和装配焊接电子元件用的焊盘组成，既具有导通各层线路，又具有相互间绝缘的作用。随着SMT（表面安装技术）的不断发展，以及新一代SMD（表面安装器件）的不断推出，如QFP、QFN、CSP、BGA（特别是MBGA），使电子产品更加智能化、小型化，因而推动了PCB工业技术的重大改革和进步。自1991年IBM公司首先成功开发出高密度多层板（SLC）以来，各国各大集团也相继开发出各种各样的高密度互连（HDI）微孔板。这些加工技术的迅猛发展，促使了PCB的设计已逐渐向多层、高密度布线的方向发展。多层印制板以其设计灵活、稳定可靠的电气性能和优越的经济性能，现已广泛应用于电子产品的生产制造中。下面，作者以多年设计印制板的经验，着重印制板的电气性能，结合工艺要求，从印制板稳定性、可靠性方面，来谈谈多层制板设计的基本要领。
上传时间： 2013-11-19
上传用户：zczc
