Recently a new technology for high voltage Power MOSFETshas been introduced – the CoolMOS™ . Based on thenew device concept of charge compensation the RDS(on) areaproduct for E.g. 600V transistors has been reduced by afactor of 5. The devices show no bipolar current contributionlike the well known tail current observed during the turn-offphase of IGBTs. CoolMOS™ virtually combines the lowswitching losses of a MOSFET with the on-state losses of anIGBT.
标签: COOLMOS
上传时间: 2013-11-14
上传用户:zhyiroy
Abstract: A laser module designer can use a fixed resistor, mechanical pot, digital pot, or a digital-to-analogconverter (DAC) to control the laser driver's modulation and bias currents. The advantages of a programmablemethod (POT or DAC) are that the manufacturing process can be automated and digital control can be applied(E.g., to compensate for temperature). Using POTs can be a more simple approach than a DAC. There can be aslight cost advantage to using a POT, but this is usually not significant relative to other pieces of the design.Using a DAC can offer advantages, including improved linearity (translating to ease of software implementationand ability to hit the required accuracy), increased board density, a wider range of resolutions, a betteroptimization range, ease of use with a negative voltage laser driver, and unit-to-unit consistency
上传时间: 2013-11-13
上传用户:ca05991270
Avalanche photodiodes (APDs) are widely utilized in laserbased fiberoptic systems to convert optical data intoelectrical form. The APD is usually packaged with a signalconditioning amplifier in a small module. An APD receivermodule and attendant circuitry appears in Figure 1. TheAPD module (figure right) contains the APD and a transimpedance(E.g., current-to-voltage) amplifier. An opticalport permits interfacing fiberoptic cable to the APD’sphotosensitive portion. The module’s compact constructionfacilitates a direct, low loss connection between theAPD and the amplifier, necessary because of the extremelyhigh speed data rates involved
上传时间: 2013-10-25
上传用户:brain kung
All inputs of the C16x family have Schmitt-Trigger input characteristics. These Schmitt-Triggers are intended to always provide proper internal low and high levels, even if anundefined voltage level (between TTL-VIL and TTL-VIH) is externally applied to the pin.The hysteresis of these inputs, however, is very small, and can not be properly used in anapplication to suppress signal noise, and to shape slow rising/falling input transitions.Thus, it must be taken care that rising/falling input signals pass the undefined area of theTTL-specification between VIL and VIH with a sufficient rise/fall time, as generally usualand specified for TTL components (E.g. 74LS series: gates 1V/us, clock inputs 20V/us).The effect of the implemented Schmitt-Trigger is that even if the input signal remains inthe undefined area, well defined low/high levels are generated internally. Note that allinput signals are evaluated at specific sample points (depending on the input and theperipheral function connected to it), at that signal transitions are detected if twoconsecutive samples show different levels. Thus, only the current level of an input signalat these sample points is relevant, that means, the necessary rise/fall times of the inputsignal is only dependant on the sample rate, that is the distance in time between twoconsecutive evaluation time points. If an input signal, for instance, is sampled throughsoftware every 10us, it is irrelevant, which input level would be seen between thesamples. Thus, it would be allowable for the signal to take 10us to pass through theundefined area. Due to the sample rate of 10us, it is assured that only one sample canoccur while the signal is within the undefined area, and no incorrect transition will bedetected. For inputs which are connected to a peripheral function, E.g. capture inputs, thesample rate is determined by the clock cycle of the peripheral unit. In the case of theCAPCOM unit this means a sample rate of 400ns @ 20MHz CPU clock. This requiresinput signals to pass through the undefined area within these 400ns in order to avoidmultiple capture events.For input signals, which do not provide the required rise/fall times, external circuitry mustbe used to shape the signal transitions.In the attached diagram, the effect of the sample rate is shown. The numbers 1 to 5 in thediagram represent possible sample points. Waveform a) shows the result if the inputsignal transition time through the undefined TTL-level area is less than the time distancebetween the sample points (sampling at 1, 2, 3, and 4). Waveform b) can be the result ifthe sampling is performed more than once within the undefined area (sampling at 1, 2, 5,3, and 4).Sample points:1. Evaluation of the signal clearly results in a low level2. Either a low or a high level can be sampled here. If low is sampled, no transition willbe detected. If the sample results in a high level, a transition is detected, and anappropriate action (E.g. capture) might take place.3. Evaluation here clearly results in a high level. If the previous sample 2) had alreadydetected a high, there is no change. If the previous sample 2) showed a low, atransition from low to high is detected now.
上传时间: 2013-10-23
上传用户:copu
All inputs of the C16x family have Schmitt-Trigger input characteristics. These Schmitt-Triggers are intended to always provide proper internal low and high levels, even if anundefined voltage level (between TTL-VIL and TTL-VIH) is externally applied to the pin.The hysteresis of these inputs, however, is very small, and can not be properly used in anapplication to suppress signal noise, and to shape slow rising/falling input transitions.Thus, it must be taken care that rising/falling input signals pass the undefined area of theTTL-specification between VIL and VIH with a sufficient rise/fall time, as generally usualand specified for TTL components (E.g. 74LS series: gates 1V/us, clock inputs 20V/us).The effect of the implemented Schmitt-Trigger is that even if the input signal remains inthe undefined area, well defined low/high levels are generated internally. Note that allinput signals are evaluated at specific sample points (depending on the input and theperipheral function connected to it), at that signal transitions are detected if twoconsecutive samples show different levels. Thus, only the current level of an input signalat these sample points is relevant, that means, the necessary rise/fall times of the inputsignal is only dependant on the sample rate, that is the distance in time between twoconsecutive evaluation time points. If an input signal, for instance, is sampled throughsoftware every 10us, it is irrelevant, which input level would be seen between thesamples. Thus, it would be allowable for the signal to take 10us to pass through theundefined area. Due to the sample rate of 10us, it is assured that only one sample canoccur while the signal is within the undefined area, and no incorrect transition will bedetected. For inputs which are connected to a peripheral function, E.g. capture inputs, thesample rate is determined by the clock cycle of the peripheral unit. In the case of theCAPCOM unit this means a sample rate of 400ns @ 20MHz CPU clock. This requiresinput signals to pass through the undefined area within these 400ns in order to avoidmultiple capture events.
上传时间: 2014-04-02
上传用户:han_zh
当拿到一张CASE单时,首先得确定的是能用什么母体才能实现此功能,然后才能展开对外围硬件电路的设计,因此首先得了解每个母体的基本功能及特点,下面大至的介绍一下本公司常用的IC:单芯片解决方案• SN8P1900 系列– 高精度 16-Bit 模数转换器– 可编程运算放大器 (PGIA)• 信号放大低漂移: 2V• 放大倍数可编程: 1/16/64/128 倍– 升压- 稳压调节器 (Charge-Pump Regulator)• 电源输入: 2.4V ~ 5V• 稳压输出: E.g. 3.8V at SN8P1909– 内置液晶驱动电路 (LCD Driver)– 单芯片解决方案 • 耳温枪 SN8P1909 LQFP 80 Pins• 5000 解析度量测器 SN8P1908 LQFP 64 Pins• 体重计 SN8P1907 SSOP 48 Pins单芯片解决方案• SN8P1820 系列– 精确的12-Bit 模数转换器– 可编程运算放大器 (PGIA)• Gain Stage One: Low Offset 5V, Gain: 16/32/64/128• Gain Stage One: Low Offset 2mV, Gain: 1.3 ~ 2.5– 升压- 稳压调节器• 电源输入: 2.4V ~ 5V• 稳压输出: E.g. 3.8V at SN8P1829– 内置可编程运算放大电路– 内置液晶驱动电路 – 单芯片解决方案 • 电子医疗器 SN8P1829 LQFP 80 Pins 高速/低功耗/高可靠性微控制器• 最新SN8P2000 系列– SN8P2500/2600/2700 系列– 高度抗交流杂讯能力• 标准瞬间电压脉冲群测试 (EFT): IEC 1000-4-4• 杂讯直接灌入芯片电源输入端• 只需添加1颗 2.2F/50V 旁路电容• 测试指标稳超 4000V (欧规)– 高可靠性复位电路保证系统正常运行• 支持外部复位和内部上电复位• 内置1.8V 低电压侦测可靠复位电路• 内置看门狗计时器保证程序跳飞可靠复位– 高抗静电/栓锁效应能力– 芯片工作温度有所提高: -200C ~ 700C 工规芯片温度: -400C ~ 850C 高速/低功耗/高可靠性微控制器• 最新 SN8P2000 系列– SN8P2500/2600/2700 系列– 1T 精简指令级结构• 1T: 一个外部振荡周期执行一条指令• 工作速度可达16 MIPS / 16 MHz Crystal– 工作消耗电流 < 2mA at 1-MIPS/5V– 睡眠模式下消耗电流 < 1A / 5V额外功能• 高速脉宽调制输出 (PWM)– 8-Bit PWM up to 23 KHz at 12 MHz System Clock– 6-Bit PWM up to 93 KHz at 12 MHz System Clock– 4-Bit PWM up to 375 KHz at 12 MHz System Clock• 内置高速16 MHz RC振荡器 (SN8P2501A)• 电压变化唤醒功能• 可编程控制沿触发/中断功能– 上升沿 / 下降沿 / 双沿触发• 串行编程接口
上传时间: 2013-10-21
上传用户:jiahao131
用单片机配置FPGA—PLD设计技巧 Configuration/Program Method for Altera Device Configure the FLEX Device You can use any Micro-Controller to configure the FLEX device–the main idea is clocking in ONE BITof configuration data per CLOCK–start from the BIT 0The total Configuration time–E.g. 10K10 need 15K byte configuration file•calculation equation–10K10* 1.5= 15Kbyte–configuration time for the file itself•15*1024*8*clock = 122,880Clock•assume the CLOCK is 4MHz•122,880*1/4Mhz=30.72msec
上传时间: 2013-10-09
上传用户:a67818601
创新、效能、卓越是ADI公司的文化支柱。作为业界公认的全球领先数据转换和信号调理技术领先者,我们除了提供成千上万种产品以外,还开发了全面的设计工具,以便客户在整个设计阶段都能轻松快捷地评估电路。
上传时间: 2013-11-25
上传用户:kachleen
创新、效能、卓越是ADI公司的文化支柱。作为业界公认的全球领先数据转换和信号调理技术领先者,我们除了提供成千上万种产品以外,还开发了全面的设计工具,以便客户在整个设计阶段都能轻松快捷地评估电路。
上传时间: 2013-10-18
上传用户:cxl274287265
prolog 找路例子程序: === === === === === === Part 1-Adding connections Part 2-Simple Path example | ?- path1(a,b,P,T). will produce the response: T = 15 P = [a,b] ? Part 3 - Non-repeating path As an example, the query: ?- path2(a,h,P,T). will succeed and may produce the bindings: P = [a,depot,b,d,e,f,h] T = 155 Part 4 - Generating a path below a cost threshold As an example, the query: ?- path_below_cost(a,[a,b,c,d,e,f,g,h],RS,300). returns: RS = [a,b,depot,c,d,e,g,f,h] ? RS = [a,c,depot,b,d,e,g,f,h] ? no ==================================
标签: Part connections example prolog
上传时间: 2015-04-24
上传用户:ljt101007