用verilog语言编写，一个8-bit ALU，可以完成按字节的+、-和与、或、非操作
上传时间： 2013-12-06
上传用户：妄想演绎师
环形缓冲库，单位是BIT，读写指针独立，测试通过
标签： 环形
上传时间： 2013-12-23
上传用户：wff
This sample provides a generic example of a PCI IDE minidriver. The sample isolates vendor-specific code from the higher-level PCI IDE bus driver, much as SCSI minidrivers isolate code from the SCSI port driver. See the Release Notes section for more information. This sample works on both x86 and Alpha platforms, and is 64-bit compliant. It builds with Microsoft® Visual C® 6.0. It does not implement Plug and Play or Power Management.
标签： sample vendor-specific minidriver provides
上传时间： 2013-12-20
上传用户：wyc199288
Addfilter is a command-line application which adds and removes filter drivers for a given drive or volume. It is intended to demonstrate how to insert a filter driver into the driver stack of a device. The sample illustrates how to do this by using the SetupDi APIs. The sample works on the x86 platform. It has only been tested in a 32-bit environment. Since Addfilter is not a driver, it does not deal with Plug and Play or Power Management. No INF file is needed to install this application.
标签： command-line application Addfilter drivers
上传时间： 2016-06-28
上传用户：源码3
The CD Audio sample allows some non-SCSI2 CD ROMs to support audio operations by intercepting the relevant audio ioctls and translating them into the command block(s) expected by the non-compliant cdroms. It supports Plug and Play and Power Management, and is 64-bit compliant. No INF file is needed to install this driver.
标签： intercepting operations non-SCSI support
上传时间： 2014-08-17
上传用户：pkkkkp
The DiskPerf filter driver monitors disk-accesses, capturing performance data. It supports Plug and Play, Power Management, and WMI . It is not 64-bit compliant. No INF file is needed to install this driver.
标签： disk-accesses performance capturing DiskPerf
上传时间： 2013-12-31
上传用户：wuyuying
123456uyygbb温度传感器ds1820 的汇编程序 晶振：12M TEMPER_L EQU 36H TEMPER_H EQU 35H TEMPER_NUM EQU 60H FLAG1 BIT 00H DQ BIT P3.3 AAA:MOV SP,#70H LCALL GET_TEMPER LCALL TEMPER_COV LJMP AAA NOP ------------------读出转换后的温度值 GET_TEMPER: SETB DQ 定时入口 BCD:LCALL INIT_1820 JB FLAG1,S22 LJMP BCD 若DS18B20不存在则返回 S22:LCALL DELAY1 MOV A,#0CCH 跳过ROM匹配------0CC LCALL WRITE_1820 MOV A,#44H 发出温度转换命令 LCALL WRITE_1820
标签： EQU TEMPER_NUM TEMPER_L TEMPER_H
上传时间： 2013-12-26
上传用户：ainimao
本程序使用MSP430F149驱动DS18B20，并再1602液晶显示温度；DS18B20 是一款小巧的温度传感器，它通过单总线协议与 MCU 进行通信，硬件连接十分简洁，它具有如下特性：测温范围-55℃～+125℃，并且在-10℃～+85℃范围内具有±0.5℃的精度，9-Bit 到 12-Bit 的可编程分辨率，用户自定义、非易失性温度阈值。MCU的P1.6端口与DS18B20的DQ端连接， 通过在MCU的IO 端口模拟1-Wire协议的时序就能实现对 DS18B20 的读写了。
上传时间： 2016-07-04
上传用户：凤临西北
这是一个用VHDL写的简易的CPU的程序，共支持10条指令。使用微指令方式。包括.bit文件。下载到FPGA芯片上成功。注解不小心忘记保存。
上传时间： 2014-12-01
上传用户：l254587896
摘自university of waterloo的个别知道笔记，主要关于electrical and computer engineering方面，包括了8-bit hamming的编解码以及使用VHDL的硬件开发
标签： university waterloo of
上传时间： 2016-07-07
上传用户：qq521
