map.mrp

TOSHIBA公司的射频卡VERILOGHDL代码 包括TOP 顶层文件

Xilinx Mapping Report File for Design 't6n76_3'
Copyright (c) 1995-1999 Xilinx, Inc.  All rights reserved.

Design Information
------------------
Command Line   : m1map -p xc4085xl-1-bg432 -o map.ncd t6n76_3.ngd t6n76_3.pcf 
Target Device  : x4085xl
Target Package : bg432
Target Speed   : -1
Mapper Version : xc4000xl -- C.22

Design Summary
--------------
   Number of errors:        0
   Number of warnings:      3
   Number of CLBs:            424 out of  3136   13%
      CLB Flip Flops:     283
      CLB Latches:          0
      4 input LUTs:       780 (1 used as route-throughs)
      3 input LUTs:       112 (7 used as route-throughs)
   Number of bonded IOBs:      34 out of   352    9%
      IOB Flops:           11
      IOB Latches:          0
   Number of TBUFs:            16 out of  6496    1%
   Number of BUFGLSs:           5 out of     8   62%
Total equivalent gate count for design: 7133
Additional JTAG gate count for IOBs:    1632

Table of Contents
-----------------
Section 1 - Errors
Section 2 - Warnings
Section 3 - Design Attributes
Section 4 - Removed Logic Summary
Section 5 - Removed Logic
Section 6 - Added Logic
Section 7 - Expanded Logic
Section 8 - Signal Cross-Reference
Section 9 - Symbol Cross-Reference
Section 10 - IOB Properties
Section 11 - RPMs
Section 12 - Guide Report

Section 1 - Errors
------------------

Section 2 - Warnings
--------------------
WARNING:OldMap:78 - All of the external outputs in this design are using
   slew-rate-limited output drivers.  The delay on speed critical outputs can be
   dramatically reduced by designating them as fast outputs in the original
   design.  Please see your vendor interface documentation for specific
   information on how to do this within your design-entry tool.
   Note: You should be careful not to designate too many outputs which switch
   together as fast, because this can cause excessive ground bounce.  For more
   information on this subject, please refer to the IOB switching characteristic
   guidelines for the device you are using in the Programmable Logic Data Book.
WARNING:OldMap:929 - Signal `mainU_stat<6>' on pin A1 of CY4 symbol
   "mainU_C3089_C3_C2" (output signal=mainU_C3089_C3_cout0_net) is not required
   by carry mode ADD-F-CI.  The signal is being removed. 
WARNING:OldMap:929 - Signal `mainU_clockdivU_c<6>' on pin A1 of CY4 symbol
   "mainU_clockdivU_C106_C3_C2" (output
   signal=mainU_clockdivU_C106_C3_cout0_net) is not required by carry mode
   DEC-F-CI.  The signal is being removed. 

Section 3 - Design Attributes
-----------------------------
 Attribute LOC
   "R2" on symbol "breset0.PAD"
   "V4" on symbol "rfClk0.PAD"
   "P4" on symbol "rfData.PAD"
   "R1" for signal(s) rfOut on symbol "rfOut.PAD"
   "M4" for signal(s) sramcs on symbol "sramcs.PAD"
   "N1" for signal(s) sramoe on symbol "sramoe.PAD"
   "N2" for signal(s) sramwe on symbol "sramwe.PAD"
   "F4" for signal(s) sramAD<9> on symbol "sramAD<9>.PAD"
   "G2" for signal(s) sramAD<8> on symbol "sramAD<8>.PAD"
   "G3" for signal(s) sramAD<7> on symbol "sramAD<7>.PAD"
   "H1" for signal(s) sramAD<6> on symbol "sramAD<6>.PAD"
   "H2" for signal(s) sramAD<5> on symbol "sramAD<5>.PAD"
   "H3" for signal(s) sramAD<4> on symbol "sramAD<4>.PAD"
   "H4" for signal(s) sramAD<3> on symbol "sramAD<3>.PAD"
   "J2" for signal(s) sramAD<2> on symbol "sramAD<2>.PAD"
   "J3" for signal(s) sramAD<1> on symbol "sramAD<1>.PAD"
   "J4" for signal(s) sramAD<0> on symbol "sramAD<0>.PAD"
   "K1" for signal(s) sramDT<7> on symbol "sramDT<7>.PAD"
   "K2" for signal(s) sramDT<6> on symbol "sramDT<6>.PAD"
   "K3" for signal(s) sramDT<5> on symbol "sramDT<5>.PAD"
   "K4" for signal(s) sramDT<4> on symbol "sramDT<4>.PAD"
   "L3" for signal(s) sramDT<3> on symbol "sramDT<3>.PAD"
   "M1" for signal(s) sramDT<2> on symbol "sramDT<2>.PAD"
   "M2" for signal(s) sramDT<1> on symbol "sramDT<1>.PAD"
   "M3" for signal(s) sramDT<0> on symbol "sramDT<0>.PAD"
   "D1" for signal(s) sramAD<18> on symbol "sramAD<18>.PAD"
   "D2" for signal(s) sramAD<17> on symbol "sramAD<17>.PAD"
   "E1" for signal(s) sramAD<16> on symbol "sramAD<16>.PAD"
   "E2" for signal(s) sramAD<15> on symbol "sramAD<15>.PAD"
   "E3" for signal(s) sramAD<14> on symbol "sramAD<14>.PAD"
   "E4" for signal(s) sramAD<13> on symbol "sramAD<13>.PAD"
   "F1" for signal(s) sramAD<12> on symbol "sramAD<12>.PAD"
   "F2" for signal(s) sramAD<11> on symbol "sramAD<11>.PAD"
   "F3" for signal(s) sramAD<10> on symbol "sramAD<10>.PAD"

Section 4 - Removed Logic Summary
---------------------------------
   2 block(s) optimized away

Section 5 - Removed Logic
-------------------------

Optimized Block(s):
TYPE 		BLOCK
LDCE_1 		EEPEmu0_sramcs_reg/$1I13
X_ZERO 		N334.ZERO

To enable printing of redundant blocks removed and signals merged, set the
detailed map report option and rerun map.

Section 6 - Added Logic
-----------------------

Section 7 - Expanded Logic
--------------------------
To enable this section, set the detailed map report option and rerun map.

Section 8 - Signal Cross-Reference
----------------------------------
To enable this section, set the detailed map report option and rerun map.

Section 9 - Symbol Cross-Reference
----------------------------------
To enable this section, set the detailed map report option and rerun map.

Section 10 - IOB Properties
---------------------------
"rfData" (IOB) : INFF
"rfOut" (IOB) : SLEW=SLOW
"sramAD<0>" (IOB) : SLEW=SLOW OUTFF
"sramAD<10>" (IOB) : SLEW=SLOW
"sramAD<11>" (IOB) : SLEW=SLOW
"sramAD<12>" (IOB) : SLEW=SLOW
"sramAD<13>" (IOB) : SLEW=SLOW
"sramAD<14>" (IOB) : SLEW=SLOW
"sramAD<15>" (IOB) : SLEW=SLOW
"sramAD<16>" (IOB) : SLEW=SLOW
"sramAD<17>" (IOB) : SLEW=SLOW
"sramAD<18>" (IOB) : SLEW=SLOW
"sramAD<1>" (IOB) : SLEW=SLOW OUTFF
"sramAD<2>" (IOB) : SLEW=SLOW OUTFF
"sramAD<3>" (IOB) : SLEW=SLOW OUTFF
"sramAD<4>" (IOB) : SLEW=SLOW OUTFF
"sramAD<5>" (IOB) : SLEW=SLOW OUTFF
"sramAD<6>" (IOB) : SLEW=SLOW OUTFF
"sramAD<7>" (IOB) : SLEW=SLOW OUTFF
"sramAD<8>" (IOB) : SLEW=SLOW OUTFF
"sramAD<9>" (IOB) : SLEW=SLOW OUTFF
"sramcs" (IOB) : SLEW=SLOW
"sramDT<0>" (IOB) : SLEW=SLOW
"sramDT<1>" (IOB) : SLEW=SLOW
"sramDT<2>" (IOB) : SLEW=SLOW
"sramDT<3>" (IOB) : SLEW=SLOW
"sramDT<4>" (IOB) : SLEW=SLOW
"sramDT<5>" (IOB) : SLEW=SLOW
"sramDT<6>" (IOB) : SLEW=SLOW
"sramDT<7>" (IOB) : SLEW=SLOW
"sramoe" (IOB) : SLEW=SLOW
"sramwe" (IOB) : SLEW=SLOW

Section 11 - RPMs
-----------------

Section 12 - Guide Report
-------------------------
Guide not run on this design.