new_top.mrp

自己在ISE下用VHDL写的UART

Release 6.3i Map G.35
Xilinx Mapping Report File for Design 'new_top'

Design Information
------------------
Command Line   : D:/Xilinx/bin/nt/map.exe -intstyle ise -p xc4vlx25-sf363-10 -cm
area -pr b -k 4 -c 100 -tx off -o new_top_map.ncd new_top.ngd new_top.pcf 
Target Device  : x4vlx25
Target Package : sf363
Target Speed   : -10
Mapper Version : virtex4 -- $Revision: 1.16.8.2 $
Mapped Date    : Wed Apr 12 15:33:02 2006

Design Summary
--------------
Number of errors:      0
Number of warnings:    2
Logic Utilization:
  Number of Slice Flip Flops:          77 out of  21,504    1%
  Number of 4 input LUTs:              58 out of  21,504    1%
Logic Distribution:
  Number of occupied Slices:                           63 out of  10,752    1%
    Number of Slices containing only related logic:      63 out of      63  100%
    Number of Slices containing unrelated logic:          0 out of      63    0%
      *See NOTES below for an explanation of the effects of unrelated logic
Total Number 4 input LUTs:             68 out of  21,504    1%
  Number used as logic:                 58
  Number used as a route-thru:          10
  Number of bonded IOBs:                5 out of     240    2%
  Number of BUFG/BUFGCTRLs:             3 out of      32    9%
    Number used as BUFGs:                3
    Number used as BUFGCTRLs:            0

Total equivalent gate count for design:  1,088
Additional JTAG gate count for IOBs:  240
Peak Memory Usage:  123 MB

NOTES:

   Related logic is defined as being logic that shares connectivity -
   e.g. two LUTs are "related" if they share common inputs.
   When assembling slices, Map gives priority to combine logic that
   is related.  Doing so results in the best timing performance.

   Unrelated logic shares no connectivity.  Map will only begin
   packing unrelated logic into a slice once 99% of the slices are
   occupied through related logic packing.

   Note that once logic distribution reaches the 99% level through
   related logic packing, this does not mean the device is completely
   utilized.  Unrelated logic packing will then begin, continuing until
   all usable LUTs and FFs are occupied.  Depending on your timing
   budget, increased levels of unrelated logic packing may adversely
   affect the overall timing performance of your design.


Table of Contents
-----------------
Section 1 - Errors
Section 2 - Warnings
Section 3 - Informational
Section 4 - Removed Logic Summary
Section 5 - Removed Logic
Section 6 - IOB Properties
Section 7 - RPMs
Section 8 - Guide Report
Section 9 - Area Group Summary
Section 10 - Modular Design Summary
Section 11 - Timing Report
Section 12 - Configuration String Information
Section 13 - Additional Device Resource Counts

Section 1 - Errors
------------------

Section 2 - Warnings
--------------------
WARNING:LIT:175 - Clock buffer is designated to drive clock loads. BUFG symbol
   "rxd_BUFGP/BUFG" (output signal=rxd_BUFGP) has a mix of clock and non-clock
   loads. Some of the non-clock loads are (maximum of 5 listed):
   Pin I1 of XLXI_1__n0016_SW10
   Pin I1 of XLXI_1__n00230
   Pin I1 of XLXI_1__n00210
   Pin I1 of XLXI_1__n00240
   Pin I1 of XLXI_1__n00190
WARNING:LIT:176 - Clock buffer is designated to drive clock loads. BUFG symbol
   "XLXI_1_clkdiv_BUFG" (output signal=XLXI_1_clkdiv) has a mix of clock and
   non-clock loads. The non-clock loads are:
   Pin D of XLXI_1_clkdiv

Section 3 - Informational
-------------------------
INFO:LIT:95 - All of the external outputs in this design are using slew rate
   limited output drivers. The delay on speed critical outputs can be
   dramatically reduced by designating them as fast outputs in the schematic.
INFO:MapLib:562 - No environment variables are currently set.

Section 4 - Removed Logic Summary
---------------------------------
   2 block(s) optimized away

Section 5 - Removed Logic
-------------------------

Optimized Block(s):
TYPE 		BLOCK
GND 		XST_GND
VCC 		XST_VCC

To enable printing of redundant blocks removed and signals merged, set the
detailed map report option and rerun map.

Section 6 - IOB Properties
--------------------------

+----------------------------------------------------------------------------------------------------------------------------------------+
| IOB Name                           | Type             | Direction | IO Standard | Drive    | Slew | Reg (s)      | Resistor | IOB      |
|                                    |                  |           |             | Strength | Rate |              |          | Delay    |
+----------------------------------------------------------------------------------------------------------------------------------------+
| busy                               | IOB              | OUTPUT    | LVCMOS25    | 12       | SLOW | OFF1         |          |          |
| clk100m                            | IOB              | INPUT     | LVCMOS25    |          |      |              |          |          |
| rst                                | IOB              | INPUT     | LVCMOS25    |          |      |              |          |          |
| rxd                                | IOB              | INPUT     | LVCMOS25    |          |      |              |          |          |
| txd                                | IOB              | OUTPUT    | LVCMOS25    | 12       | SLOW | OFF1         |          |          |
+----------------------------------------------------------------------------------------------------------------------------------------+

Section 7 - RPMs
----------------

Section 8 - Guide Report
------------------------
Guide not run on this design.

Section 9 - Area Group Summary
------------------------------
No area groups were found in this design.

Section 10 - Modular Design Summary
-----------------------------------
Modular Design not used for this design.

Section 11 - Timing Report
--------------------------
This design was not run using timing mode.

Section 12 - Configuration String Details
-----------------------------------------
Use the "-detail" map option to print out Configuration Strings

Section 13 - Additional Device Resource Counts
----------------------------------------------
Number of JTAG Gates for IOBs = 5
Number of Equivalent Gates for Design = 1,088
Number of RPM Macros = 0
Number of Hard Macros = 0
USR_ACCESS_VIRTEX4 = 0
BUFIO = 0
GT11CLK = 0
GT11 = 0
IDELAYCTRL = 0
FRAME_ECC_VIRTEX4 = 0
STARTUP_VIRTEX4 = 0
JTAGPPC = 0
ICAP_VIRTEX4 = 0
DPM = 0
DCI_TEST = 0
DCIRESET = 0
CAPTURE_VIRTEX4 = 0
BSCAN_VIRTEX4 = 0
OSERDES = 0
ISERDES = 0
BUFR = 0
EMAC = 0
PPC405_ADV = 0
MONITOR = 0
PMCD = 0
DCM_ADV = 0
DSP48 = 0
Total Registers (Flops & Latches in Slices & IOBs) not driven by LUTs = 63
IOB Dual-Rate Flops not driven by LUTs = 0
IOB Dual-Rate Flops = 0
IOB Slave Pads = 0
IOB Master Pads = 0
IOB Latches not driven by LUTs = 0
IOB Latches = 0
IOB Flip Flops not driven by LUTs = 0
IOB Flip Flops = 0
Unbonded IOBs = 0
Bonded IOBs = 5
Shift Registers = 0
Static Shift Registers = 0
Dynamic Shift Registers = 0
16x1 ROMs = 0
16x1 RAMs = 0
32x1 RAMs = 0
Dual Port RAMs = 0
MUXFXs = 0
MULTANDs = 0
4 input LUTs used as Route-Thrus = 10
4 input LUTs = 58
Slice Latches not driven by LUTs = 0
Slice Latches = 0
Slice Flip Flops not driven by LUTs = 63
Slice Flip Flops = 77
SliceMs = 0
SliceLs = 63
Slices = 63
Number of LUT signals with 4 loads = 1
Number of LUT signals with 3 loads = 3
Number of LUT signals with 2 loads = 5
Number of LUT signals with 1 load = 43
NGM Average fanout of LUT = 2.53
NGM Maximum fanout of LUT = 30
NGM Average fanin for LUT = 3.1034
Number of LUT symbols = 58
Number of IPAD symbols = 3
Number of IBUF symbols = 3
Number of BUFG symbols = 3