The LTM8020, LTM8021, LTM8022 and LTM8023 μModule®regulators are complete easy-to-use encapsulated stepdownDC/DC regulators intended to take the pain and aggravationout of implementing a switching power supplyonto a system board. With a μModule regulator, you onlyneed an input cap, output cap and one or two resistorsto complete the design. As one might imagine, this highlevel of integration greatly simplifi es the task of printedcircuit board design, reducing the effort to four categories:component footprint generation, component placement,routing the nets, and thermal vias.
上传时间： 2014-01-18
上传用户：laomv123
The design of battery-powered equipment can often bequite challenging. Since few ICs can operate directly fromthe end-of-life voltage from a 2-cell battery (about 1.8V),most systems require a DC/DCconverter. The systemdesigner often has a limited area in which to place the DC/DC converter; associated inductors and capacitors must be
上传时间： 2013-11-23
上传用户：wys0120
锁定放大是微弱信号检测的重要手段。基于相关检测理论，利用开关电容的开关实现锁定放大器中乘法器的功能，提出开关电容和积分器相结合以实现相关检测的方法，并设计出一种锁定放大器。该锁定放大器将微弱信号转化为与之相关的方波，通过后续电路得到正比于被测信号的直流电平，为后续采集处理提供方便。测量数据表明锁定放大器前级可将10-6 A的电流转换为10-1 V的电压，后级通过带通滤波器级联可将信号放大1×105倍。该方法在降低噪声的同时，可对微弱信号进行放大，线性度较高、稳定性较好。 Abstract: Lock-in Amplifying（LIA）is one of important means for weak signal detection. Based on cross-correlation detection theory， switch in the swithched capacitor was used as multiplier of LIA， and a new method of correlation detection was proposed combining swithched capacitor with integrator. A kind of LIA was designed which can convert the weak signal to square-wave， then DC proportional to measured signal was obtained through follow-up conditioning circuit， providing convenience for signal acquisition and processing. The measured data shows that the electric current（10-6 A） can be changed into voltage（10-1 V） by LIA， and the signal is magnified 1×105 times by cascade band-pass filter. The noise is suppressed and the weak signal is amplified. It has the advantages of good linearity and stability.
上传时间： 2013-11-29
上传用户：黑漆漆
When a system designer specifies a nonisolated dc/dc powermodule, considering the needed input voltage range isequally as important as considering the required performanceattributes and features. Generally, nonisolated moduleshave either a narrow or a wide input voltage range. Narrowinputmodules typically have a nominal input voltage of3.3, 5, or 12 V. For systems that operate from a tightlyregulated input bus—such as those that do not use batterybackup—a narrow-input module is often adequate sincethe input remains fairly stable.Offering greater flexibility, wide-input modules operatewithin a range of 7 to 36 V, which includes the popular12- or 24-V industrial bus. This enables a single module tobe used for generating multiple voltages. These modulesare ideal for industrial controls, HVAC systems, vehicles,medical instrumentation, and other applications that usea loosely regulated distribution bus. In addition, systemspowered by a rectifier/battery charger with lead-acidbattery backup almost always require wide-input modules.System designers who choose power supplies may wantto take a close look at the latest generation of wide-inputdc/dc modules.
标签： Wide-input modules offer dc
上传时间： 2014-12-24
上传用户：dragonhaixm
Features: High efficiency, high reliability, low cost AC input range selected by switch 100% full load burn-in test Protections: Short circuit / Over load Fixed switching frequency at 25KHz Cooling by free air convection 1 year warranty Dimensions: 199*98*38mm (L*W*H)
标签： Switchin Output Single SKS
上传时间： 2013-10-30
上传用户：taa123456
Analog Inputs and Outputs in an S7 PLC are represented in the PLC as a 16-bit integer. Over the nominal span of the analog input or output, the value of this integer will range between - 27648 and +27648. However, it is easier to use the analog values if they are scaled to the same units and ranges as the process being controlled. This applications tip describes methods for scaling analog values to and from engineering units.
上传时间： 2013-11-17
上传用户：3294322651
数字控制的交流调速系统所选用的微处理器、功率器件及产生PWM波的方法是影响交流调速系统性能好坏的直接因素。在介绍了正弦脉宽调制(SPWM)技术的基础上，设计了一种以8098单片机作为控制器，以智能功率模块IPM为开关器件的变频调速系统。通过软件编程，产生正弦脉冲宽度调制波形来控制绝缘栅双极晶体管的导通和关断，从而达到控制异步电动机转速的目的。实验结果表明，该系统可调频率调电压，稳定度高，调速范围宽，具有较强的实用价值 Abstract: AC variable speed with digital control systems used microprocessors， power devices and generate PWM wave is the direct factors of affecting the performance AC speed regulation system. On the basis of introducing the sinusoidal pulse width modulation (SPWM) technology，this paper designed variable speed system which used 8098 as a controller， intelligent power module IPM as switching device. Through software programming， resulting in sinusoidal pulse width modulation waveform to control the insulated gate bipolar transistor turn on and off， so as to achieve the purpose of speed control of induction motors. Experimental results show that the system can adjust frequency modulation voltage， high stability， wide speed range， has a strong practical value.
上传时间： 2013-11-14
上传用户：ynwbosss
HIGH SPEED 8051 μC CORE - Pipe-lined Instruction Architecture; Executes 70% of Instructions in 1 or 2 System Clocks - Up to 25MIPS Throughput with 25MHz System Clock - 22 Vectored Interrupt Sources MEMORY - 4352 Bytes Internal Data RAM (256 + 4k) - 64k Bytes In-System Programmable FLASH Program Memory - External Parallel Data Memory Interface – up to 5Mbytes/sec DIGITAL PERIPHERALS - 64 Port I/O; All are 5V tolerant - Hardware SMBusTM (I2CTM Compatible), SPITM, and Two UART Serial Ports Available Concurrently - Programmable 16-bit Counter/Timer Array with 5 Capture/Compare Modules - 5 General Purpose 16-bit Counter/Timers - Dedicated Watch-Dog Timer; Bi-directional Reset CLOCK SOURCES - Internal Programmable Oscillator: 2-to-16MHz - External Oscillator: Crystal, RC, C, or Clock - Real-Time Clock Mode using Timer 3 or PCA SUPPLY VOLTAGE ........................ 2.7V to 3.6V - Typical Operating Current: 10mA @ 25MHz - Multiple Power Saving Sleep and Shutdown Modes 100-Pin TQFP (64-Pin Version Available) Temperature Range: –40°C to +85°C
标签： C8051F020
上传时间： 2013-10-12
上传用户：lalalal
利用单片机具有的智能程序控制的特点，设计了基于STC89C52单片机的"二极管特性测试器"，可对二极管一般特性进行快速测试。通过稳定线性电流源给二极管加载恒定电流，然后由高精度模数转换器测试其压降，以此为基础可判断二极管好坏、检测二极管极性和测试二极管伏安特性等，避免了用万用表测试只能测得极性而不知其特性这一缺点。可用于电子设计制作过程中对二极管进行快速测试，以确定被测二极管是否满足电路的设计要求。 Abstract: By making good use of the intelligent control function of the Micro Controller Unit (MCU)， the diode trait tester was designed based on the STC89C52，which could be used to test the trait of a diode rapidly. By loading constant current to diode through the stable linear current source， and measuring the voltage drop of the diode by high-precision analogue-to-digital converter (ADC)， it can judge whether the diode is good or not， distinguish the polarity of the diode， and test the trait that the diode， which can avoid the fault of using a multimeter can only measure the polarity but not the trait. This device can be used to test the trait of a diode quickly，and to make sure that whether a diode can be used in the electronic design or not.
上传时间： 2013-11-13
上传用户：assef
The MAX9257/MAX9258 programmable serializer/deserializer (SerDes) devices transfer both video data and control signals over the same twisted-pair cable. However, control data can only be transmitted during the vertical blank time, which is indicated by the control-channel-enabled output (CCEN) signal. The electronic control unit (ECU) firmware designer needs to know how quickly to respond to the CCEN signal before it times out and how to calculate this duration. This application note describes how to calculate the duration of the CCEN for the MAX9257/MAX9258 SerDes chipset. The calculation is based on STO timeout, clock frequency, and UART bit timing. The CCEN duration is programmable and can be closed if not in use.
上传时间： 2014-01-24
上传用户：xingisme
