In industrial applications, high voltage power supply spikes with durations ranging from a few microseconds to hundreds of millisecondsare commonly encountered. The electronics in these systems must not only survive transient voltage spikes, but in many cases alsooperate reliably throughout the event.
上传时间： 2013-11-07
上传用户：redmoons
A light-emitting diode (LED) is a semiconductor device that emits narrow-spectrum incoherent light when forward-biased.The color of the emitted light depends on the chemical composition of the semiconductor material used, and can benear-ultraviolet, visible or infrared. LEDs are more prevalent today than ever before, replacing traditional incandescent andfluorescent bulbs in many lighting applications. Incandescents use a heated filament, are subject to breakage and burnoutand operate at a luminous efficiency of 2% to 4%. Fluorescents are more efficient, at 7% to 12%, but require highdrive voltage and contain mercury, a toxic substance that may be eventually banned in certain countries. LEDs, however,produce light directly through electroluminescence, operate at low voltage and can deliver over 20% luminous efficiency.
上传时间： 2013-11-07
上传用户：xiaoyuer
Abstract: This application note illustrates an intermediate 8V switching power supply for an automotive radio and infotainment system.The design withstands the complete automotive input voltage range (including cold crank and load dump conditions), assuring a stable8V supply for common subsystems such as a CD driver, LCDs, and a radio module in modern infotainment systems. To avoiddisturbance in the AM and FM bands, the switching power supply runs at a fixed frequency of 2MHz, enabling an ideal solution forradio systems.
上传时间： 2013-11-20
上传用户：feitian920
Abstract: We don't expect manufacturers to produce clothes that in one size that fits everyone. In thesame way, one ESD component can't solve all issues—each application has different ESD requirements.Knowing that "one size fits all" cannot apply to power design, the power designer, or the engineering"super hero," must consider all the potential disruptions to a steady flow of power and thenvarious waysto mitigate them. This tutorial describes voltage- and current-limiting devices and risetime reducers tomanage the power. It also points to free and low-cost software tools to help design lowpass filters, checkcapacitor self-resonance, and simulate circuits.
上传时间： 2013-11-18
上传用户：zhouxuepeng1
Abstract: Impedance mismatches in a radio-frequency (RF) electrical transmission line cause power loss andreflected energy. Voltage standing wave ratio (VSWR) is a way to measure transmission line imperfections. Thistutorial defines VSWR and explains how it is calculated. Finally, an antenna VSWR monitoring system is shown.
上传时间： 2013-10-19
上传用户：yuanwenjiao
Abstract: This document details the Oceanside (MAXREFDES9#) subsystem reference design, a 3.3V to 15V input,±15V (±12V) output, isolated power supply. The Oceanside design includes a high-efficiency step-up controller, a36V H-bridge transformer driver for isolated supplies, a wide input range, and adjustable output low-dropout linearregulator (LDO). Test results and hardware files are included.
上传时间： 2013-10-12
上传用户：jinyao
Abstract: Some power architectures require the power supply sequencer (or system manager) to controldownstream power MOSFETs to allow power to flow into branch circuits. This application note explains howsystem power sequencing and level shifting can be accomplished using a low-voltage system manager
上传时间： 2013-11-02
上传用户：wys0120
两节锂电充电IC-ASC8512 ASC8512 为开关型两节锂聚合物电池充电管理芯片，非常适合于便携式设备的充电管理应用。ASC8512 集内置功率MOSFET、高精度电压和电流调节器、预充、充电状态指示和充电截止等功能于一体，采用TSSOP-14、SSOP-14两种封装形式。ASC8512对电池充电分为三个阶段：预充（Pre-charge）、恒流（CC／Constant Current）、恒压（CV／Constant Voltage）过程，恒流充电电流通过外部电阻决定，最大充电电流为2A.ASC8512 集成电流限制、短路保护，确保充电芯片安全工作。ASC8512 集成NTC 热敏电阻接口，可以采集、处理电池的温度信息，保证充电电池的安全工作温度。 两节锂电池充电IC ASC8512特点： 1.充2节锂离子和锂聚合物电池 2.开关频率达400K 3.充电电流最大可做2A 4.输入电压9V到18V 5.电池状态检测 6.恒压充电电压值可通过外接电阻微调 7.千分之五的充电电压控制精度 5.防反向保护电路可防止电池电流倒灌 6.NTC 热敏接口监测电池温度 7.LED充电状态指示 8.工作环境温度范围：-20℃～70℃ 9.TSSOP-14 应用领域：应用 ●手持设备，包括医疗手持设备 ●Portable-DVD，PDA，移动蜂窝电话及智能手机 ●上网本、平板电脑、MID ●自充电电池组
上传时间： 2013-11-06
上传用户：chfanjiang
Abstract: There are many things to consider when designing a power supply for a field-programmablegate array (FPGA). These include (but are not limited to) the high number of voltage rails, and thediffering requirements for both sequencing/tracking and the voltage ripple limits. This application noteexplains these and other power-supply considerations that an engineer must think through whendesigning a power supply for an FPGA.
上传时间： 2013-11-12
上传用户：金苑科技
特点（FEATURES） 精确度0.1%满刻度（Accuracy 0.1%F.S.） 多种输入输出选择（Wide selection of input/output range） 三线式接线自动补偿线路阻抗效应（3 wire configuration automatically compensate line resistance effects） 宽范围交直流两用电源设计（Wide input range for auxiliary power） 尺寸小，稳定性高（Dimension small & High stability）
上传时间： 2013-10-17
上传用户：Huge_Brother
