Abstract: This document details the Riverside (MAXREFDES8#) subsystem reference design, a 3.3V input, 12V (15V) output, isolated power supply. The Riverside reference design includes a 3W primary-side transformer H-bridge driver for isolated supplies, and one wide input range and adjustable output low-dropout linear regulator (LDO). Test results and hardware files are included.
标签： Riverside MAXREFDES Isolated Output
上传时间： 2013-11-16
上传用户：会稽剑客
电子、电气产品的设计，必须保证在一定的电磁环境中能正常工作，既满足标准规定的抗干扰极限值要求，在受到一定的电磁干扰时，无性能降级或故障；又要满足标准规定的电磁辐射极限值的要求，对电磁环境不构成污染。所以，产品设计之初，就要从分析产品预期的电磁环境、干扰源、耦合途径和敏感部件入手，采用相应的技术措施，抑制干扰源、切断或削弱耦合途径，增强敏感部件的抗干扰能力等。文中详细介绍了一款485通讯隔离产品从辐射超标到顺利通过FCC CLASS B认证，在原理设计、PCB制板等多方面所做的各项改进措施。文中所提到的方法及规则，对产品EMC设计具有很大的参考及指导意义。
上传时间： 2013-10-24
上传用户：sz_hjbf
交流瓦特/瓦特小时，乏尔/乏尔小时转换器 特点： 精确度0.25%满刻度 多种输入,输出选择 输入与输出绝缘耐压2仟伏特/1分钟 冲击电压测试5仟伏特(1.2x50us) 突波电压测试2.5仟伏特(0.25ms/1MHz) (IEC255-4) 尺寸小，稳定性高 主要规格： 精确度: 0.25% F.S. (23 ±5℃) 输入负载: <0.2VA (Voltage) <0.2VA (Current) 最大过载能力: Current related input:3 x rated continuous 10 x rated 30 sec. ,25 x rated 3sec. 50 x rated 1sec. Voltage related input:maximum 2 x rated continuous 输出反应速度: < 250ms(0~90%) 输出负载能力: < 10mA for voltage mode < 10V for current mode 输出之涟波 : < 0.1% F.S. 脉波输出型态: Photocouple of open collector (max.30V/40mA) 归零调整范围: 0~±5% F.S. 最大值调整范围: 0~±10% F.S. 温度系数: 100ppm/℃ (0~50℃) 隔离特性: Input/Output/Power/Case 绝缘阻抗: >100Mohm with 500V DC 绝缘耐压能力: 2KVac/1 min. (input/output/power/case) 突波测试: ANSI C37.90a/1974,DIN-IEC 255-4 impulse voltage 5KV(1.2x50us) 使用环境条件: -20~60℃(20 to 90% RH non-condensed) 存放环境条件: -30~70℃(20 to 90% RH non-condensed) CE认证: EN 55022:1998/A1:2000 Class A EN 61000-3-2:2000 EN 61000-3-3:1995/A1:2001 EN 55024:1998/A1:2001
上传时间： 2013-11-11
上传用户：wettetw
AL-LJ(K)系列零序电流互感器 保定奥兰电气科技有限责任公司生产的AL-LJ(K)系列零序电流互感器经电力工业部电气设备质量检测中心检测，质量优于国标GB1208-1997《电流互感器》，具有精度高，线性度好，运行可靠，安装方便，外型美观等特点。 零序电流互感器（电缆型）的孔径范围为Ф40～Ф360，有各种容量、变比、准确限值系数，可与小电流接地选线装置、继电器、仪表等配套使用，实现对系统的检测和保护。装置具有灵敏度高，线性度好等优点。产品分整体式和组合式两类。互感器采用工程塑料外壳、树脂浇注全密封；外型美观、安装方便、节省安装空间、规格品种多，可适用各种保护装置和电力系统各种运行方式（中性点接地，中性点不接地，大电阻接地，小电阻接地和消弧线圈接地）的需要。 空格：用于小电流接地选线装置 A：与DD11/60型继电器配合使用 J：用于微机型继电保护 B：与DL11/0.2型继电器配合使用 保定市奥兰电气科技有限责任公司开发生产的零序电流互感器是一种套在电缆上的CT，它的一次绕组为穿过CT内孔的三相一次导体电缆，它的一次电流是一次三相电流的向量和（在正常、三相平衡时为0），当发生一次系统单相接地时三相平衡关系被打破，这时零序电流互感器的二次就有电流输出，供给保护装置，实现保护和监控。 零序电流互感器的一次绝缘就是电缆自身绝缘，所以这种零序电流互感器可以套在任一电压等级的电缆上。
标签： 零序电流互感器
上传时间： 2013-10-30
上传用户：fengzimili
Abstract: A resistive feedback network is often used to set the output voltage of a power supply. A mechanical potentiometer (pot)conveniently solves the problem of adjusting a power supply. For easier automatic calibration, a mechanical pot can be replaced witha digital pot. This application note presents a calibration solution that uses a digital pot, because digipots are smaller, do not movewith age or vibration, and can be recalibrated remotely. This proposed solution reduces the susceptibility of the system to thetolerance of the digital pot's end-to-end resistance, making the solution optimal fordesigners. This application note also explainssome of the equations required to calculate the resistor chain values and to use a digital pot in this way. A spreadsheet withstandard reisistor values is available for easy calculations.
上传时间： 2013-10-31
上传用户：caiguoqing
Abstract: Uses the MAX641 switching controller and an external discrete charge pump to step up the input voltage. This circuitcan service low loads and is efficient when the output is two, three, four times the input voltage. Adding the MAX627 MOSdriver can further increase the output current capability.
上传时间： 2013-11-15
上传用户：zwei41
The LT®1943 is a highly integrated, 4-output regulatordesigned to power large TFT LCD panels. The LT1943employs switching regulators—instead of linear regulators—to minimize power dissipation and accommodate awide input voltage range. The wide input range, 4.5V to22V, allows it to accept a variety of power sources,including the commonly used 5V, 12V and 19V AC adaptors.
上传时间： 2013-10-19
上传用户：yuhaihua_tony
Linear Technology offers a variety of devices that simplifyconverting power from a USB cable, but the LTC®3455represents the highest level of functional integration yet. The LTC3455 seamlessly manages power flowbetween an AC adapter, USB cable and Li-ion battery,while complying with USB power standards, all from a4mm × 4mm QFN package. In addtion, two high efficiencysynchronous buck converters generate low voltage railswhich most USB-powered peripherals require. TheLTC3455 also provides power-on reset signals for themicroprocessor, a Hot SwapTM output for poweringmemory cards as well as an uncommitted gain blocksuitable for use as a low-battery comparator or an LDOcontroller. The PCB real estate required for the entire USBpower control circuit and two DC/DC converters is only225mm2.
上传时间： 2013-11-02
上传用户：名爵少年
The LTC®3414 offers a compact and efficient voltage regulatorsolution for point of load conversion in electronicsystems that require low output voltages (down to 0.8V)from a 2.5V to 5V power bus. Internal power MOSFETswitches, with only 67mW on-resistance, allow theLTC3414 to deliver up to 4A of output current with efficiencyas high as 94%. The LTC3414 saves space by operatingwith switching frequencies as high as 4MHz, enabling theuse of tiny inductors and capacitors.
上传时间： 2014-01-03
上传用户：dongbaobao
Easy-to-use and compact point-of-load power suppliesare necessary in systems with widely distributed, highcurrent, low voltage loads. The LTC®3415 provides acompact, simple and versatile solution. It includes a pairof integrated complementary power MOSFETs (32mΩtop and 25mΩ bottom) and requires no external senseresistor. A complete design requires an inductor andinput/output capacitors, and that’s it. The result is a fast,constant frequency, 7A current mode DC/DC switchingregulator.
上传时间： 2013-10-18
上传用户：avensy
