生活中许多目标的高度和水平距离需要进行测量。目前主要的测量方法，仍以传统的皮尺丈量为主，测量效率不高，有时还很不方便，没有技术成熟的数字式测高测距产品。以基本的数学方法为理论依据，利用遥控小车做为载体，采用角度传感器测量角度、霍尔传感器测量水平距离等，通过单片机LM3S615进行数据计算，实现了对待测目标物体的高度、水平距离等数据的快速、精确和数字式的测量，高度测量精度可达99.06%，水平测量精度则可达98.06%。 Abstract: In our lives， the height and horizontal distance of some goals are needed to be measured. Because the currently used methods are still traditional tape-based measuring methods， and the measuring efficiency is low and inconvenient so some kinds of digital and portable measuring methods or instruments are needed. Based on the basic math theory， this paper designed and manufactured a portable， digital and remote controlled measuring mobile small vehicle， which assembled with angle measuring sensor for angle measurement and Hall sensor for horizontal distance measuring. MCU LM3S615 calculated the height and horizontal distance data gotten from these sensors. The measuring process is simple， the measuring results are more accurate and the measuring efficiency is higher than traditional measure instruments. The accuracy of height and distance measurement can reach 99.06% and 98.06%.
上传时间： 2013-10-30
上传用户：jackandlee
介绍一种简单射频识别系统设计。该设计包括阅读器、应答器和线圈3部分。由单片机控制阅读器向应答器发射无线信号，并接收应答器回送的信号，再通过分析回送信号识别物品。阅读器和应答器之间以半双工通信方式通信。 Abstract: A simple design of radio frequency identification system is given in this paper.The design includes reader,responder and winding.Through MCU，signals are sent to responder from reader，then corresponding signals are sent back. According to the analysis of the signals sent back，the objects can be identified.Half-duplex communication is adopted? between? reader? and? responder.
上传时间： 2013-10-11
上传用户：plsee
为了解决磁放大器性能测试过程中，需要对其供给不同数值恒定电流的问题，设计了一种基于DAC7512和单片机的数控恒流源系统。该系统采用AT89C51作为主控器件，将计算机发送的电流控制字命令转换为D/A转换器控制字，通过模拟SPI通信接口，写D/A控制字到DAC7512，从而控制其输出相应数字电压值，经差动缩放电路、电压/电路变换电路和功率驱动电路，最后输出恒定电流。实验结果表明，恒流源输出电流调节范围为-45~+45 mA、精度为±0.1 mA，分辨率达0.024 4 mA，具有应用灵活，外围电路简单，可靠性高的特点。该数控直流恒流源也可为相关产品的测试系统研发提供参考。 Abstract: In order to solve the need to supply different values constant current for the magnetic amplifier in testing process， numerical control constant current source system was designed based on DAC7512 chip and microcontroller technology. The system used the AT89C51 as the main chip， which can convert the current control word from computer into to D/A control words. And the system wrote D/A control word into the DAC7512 chip to control the output voltage value by the SPI communication interface， which can output corresponding constant current figures by scaling circuit， the V/I converter and power drive circuit. Experimental results show that the current source output current adjustment range is -45~+45mA， accuracy is ± 0.1mA， and resolution ratio is 0.024 4mA
上传时间： 2014-12-27
上传用户：invtnewer
利用Atmel公司的ATmega168微处理器，采用A/D转换方式来实现按摩椅控制器的键盘接口，通过在硬件电路中巧妙地选择电阻，在软件设计中采用数字滤波、二分法和区间鉴定等方法，灵敏可靠地实现了按摩椅中30个按键的处理。给出了硬件电路设计和软件设计思想以及部分汇编代码。 Abstract: This paper chooses A/D conversion method to realize the keyboard interface of the controller by using ATmega168 microchip from Atmel Company.It accomplishes 30-key dealing sensitively and reliably in massage chair through skillfully selecting resistors in hardware circuit and using digital filter,dichotomy and area-judging method in software design.The hardware design circuit, software design idea and partly assembles code are presented mainly.
上传时间： 2014-01-10
上传用户：咔乐坞
将现行的供暖计费方式由按建筑面积计费变为按消耗的热能计费是供暖计费方式发展趋势，为了满足这一计费方式变化的需要，设计了基于IC卡的预付费式新型供暖计费系统，通过测量用户采暖系统进出口的温度和流量，计算用户消耗的热能，利用IC卡记录用户预付费的金额和当年热能的单价，根据热能消耗和当年热能的单价计算用户采暖费，根据实际发生的供暖费用和预付费金额控制供暖的开停，这一计费方式的变化使供暖计费更趋合理。 Abstract: It is trend that the mode of heat charging is changed from billing by building area to by thermal energy. In order to meet the needs of heat charging mode changing， a new system of heat charging based on IC card is proposed. The user?蒺s energy consumption is calculated by measuring the user inlet and outlet temperature and flow，using the IC card to record the prepaid amount and the current price of heat. The user?蒺s heating costs is calculated according to energy consumption and current price， according to actual heating costs and prepaid amount，the system controls the heating opening or stopping. It is more reasonable that calculated heating costs by user heat consumption
上传时间： 2013-10-14
上传用户：大融融rr
提出一种基于单片机AT89C51SND1C的MP3播放系统的设计方案。单片机集成了专用的解码器，使用K9F1208闪存作为外存储器，放音电路采用CS4330，存储文件通过播放器上的USB接口设备从PC机上直接下载，液晶显示采用LCD1602。方案设计简单，性价比高，低功耗，易扩展。由于采用的是通用单片机实现的，可以很容易地移植到其他微控制器系统中，有很强的市场竞争能力和实用价值。 Abstract: A MP3 player design based on microchip AT89C51SND1C was presented, which used K9F1208 Flash chip as the memory circuit and used CS4330 as play chip. Storage files were download from PC through USB interfaces player on the device，and the LCD/602 was used as display screen. This system had characteristics of simple design,low power,easy expand，low cost and high recognition. Using of universual microchip make it easy to transplant to other microcontrol system，and have strong market competitiom and practical value.
上传时间： 2014-12-27
上传用户：佳期如梦
The SN65LBC170 and SN75LBC170 aremonolithic integrated circuits designed forbidirectional data communication on multipointbus-transmission lines. Potential applicationsinclude serial or parallel data transmission, cabledperipheral buses with twin axial, ribbon, ortwisted-pair cabling. These devices are suitablefor FAST-20 SCSI and can transmit or receivedata pulses as short as 25 ns, with skew lessthan 3 ns.These devices combine three 3-state differentialline drivers and three differential input linereceivers, all of which operate from a single 5-Vpower supply.The driver differential outputs and the receiverdifferential inputs are connected internally to formthree differential input/output (I/O) bus ports thatare designed to offer minimum loading to the buswhenever the driver is disabled or VCC = 0. Theseports feature a wide common-mode voltage rangemaking the device suitable for party-lineapplications over long cable runs.
上传时间： 2013-10-13
上传用户：ytulpx
Important Notice SUNPLUS INNOVATION TECHNOLOGY INC. reserves the right to change this documentation without prior notice. Information provided by SUNPLUS INNOVATION TECHNOLOGY INC. is believed to be accurate and reliable. However, SUNPLUS INNOVATION TECHNOLOGY INC.makes no warranty for any errors which may appear in this document. Contact SUNPLUS INNOVATION TECHNOLOGY INC.to obtain the latest version of device specifications before placing your order. No responsibility is assumed by SUNPLUS INNOVATION TECHNOLOGY INC. for any infringement of patent or other rights of third parties which may result from its use. In addition, SUNPLUSIT products are not authorized for use as critical components in life support systems or aviation systems, where a malfunction or failure of the product may reasonably be expected to result in significant injury to the user, without the express written approval of SunplusIT
标签： SUNPLUSIT Q-Writer 编程工具 使用说明书
上传时间： 2013-10-13
上传用户：brain kung
NXP Semiconductor designed the LPC2400 microcontrollers around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded Trace. The LPC2400 microcontrollers have 512 kB of on-chip high-speedFlash memory. This Flash memory includes a special 128-bit wide memory interface andaccelerator architecture that enables the CPU to execute sequential instructions fromFlash memory at the maximum 72 MHz system clock rate. This feature is available onlyon the LPC2000 ARM Microcontroller family of products. The LPC2400 can execute both32-bit ARM and 16-bit Thumb instructions. Support for the two Instruction Sets meansEngineers can choose to optimize their application for either performance or code size atthe sub-routine level. When the core executes instructions in Thumb state it can reducecode size by more than 30 % with only a small loss in performance while executinginstructions in ARM state maximizes core performance.
上传时间： 2013-11-15
上传用户：zouxinwang
MPLAB C30用户指南(英文) HIGHLIGHTSThe information covered in this chapter is as follows:• About this Guide• Recommended Reading• Troubleshooting• The Microchip Web Site• Development Systems Customer Notification Service• Customer Support Document LayoutThe document layout is as follows:• Chapter 1: Compiler Overview – describes MPLAB C30, development tools andfeature set.• Chapter 2: Differences between MPLAB C30 and ANSI C – describes thedifferences between the C language supported by MPLAB C30 syntax and thestandard ANSI-89 C.• Chapter 3: Using MPLAB C30 – describes how to use the MPLAB C30 compilerfrom the command line.• Chapter 4: MPLAB C30 Runtime Environment – describes the MPLAB C30runtime model, including information on sections, initialization, memory models, thesoftware stack and much more.• Chapter 5: Data Types – describes MPLAB C30 integer, floating point and pointerdata types.• Chapter 6: Device Support Files – describes the MPLAB C30 header and registerdefinition files, as well as how to use with SFR’s.• Chapter 7: Interrupts – describes how to use interrupts.• Chapter 8: Mixing Assembly Language and C Modules – provides guidelines tousing MPLAB C30 with MPLAB ASM30 assembly language modules.
上传时间： 2013-10-21
上传用户：13925096126
