基于单片机的步进电机开环控制系统:通过ATMEL89C51单片机对步进电机进行控制,主要介绍了步进电机控制器、驱动电路和LED显示电路的设计,实现了步进电机的开环控制。在步进电机控制器的设计中,重点阐述了脉冲产生电路以及对速度的控制。该系统具有成本低、控制方便的特点。关键词: 单片机; 步进电机; 开环控制 Abstract: The design using ATMEL89C51 single chip to control the step2motor with its controller, driving circuit and LED disp lay circuit to realize step motor open2loop controlwere introduced. For the controller in this design,the circuit to p roduce pulse and the speed controlwere expatiated emphatically. This system possesses features of lower cost, easier control.Key words: single ch ip; step2motor; open2loop con trol
上传时间： 2013-10-13
上传用户：cicizoe
基于PIC单片机的低功耗读卡器硬件设计:本文提出了一个完整的基于串口的智能读卡器子系统设计方案并将其实现。读卡器的设计突出了小型化的要求，全部器件使用贴片封装。为了减小读卡器的体积，设计中还使用了串口窃电的技术，使用串口信号线直接给读卡器供电。为此，读卡器使用了省电的设计，采用了省电的集成电路，并大胆简化了许多传统的设计电路。关键字： 读卡器， 单片机， 串口窃电 Abstract： This paper aims to put forward a complete design of Smart IC card reader based onSerial Port and propose the way of realizing it for the purpose of Network Security. SMD isadopted to make Smart IC reader smaller in this design. To reduce the volume of Smart ICreader， Serial Port powered technology is employed to get power from the signal line of Serial Port. For this reason， low-power consumption components are adopted in the design and some traditional designs are simplified to reduce the power consumption.Keywords： Card Reader； Single-chip Computer； Serial Port Powered IC 卡系统保存了加密算法所需要的工作密钥，供加密算法对网络上传输的数据加密使用，是整个系统网络安全的核心。在IC 卡子系统中，读卡器是一个重要的部分。它起着管理IC卡、在IC 卡和PC或网络计算机间传递数据的重要作用。本文以一片PIC单片机为核心完成了基于RS232 串口的读卡器的硬件设计。
上传时间： 2014-04-14
上传用户：wanghui2438
多功能高集成外围器件6. 1 多功能高集成外围器件82371PCI的英文名称：Peripheral Component Interconnect （外围部件互联PCI总线）；82371是PCI总线组件。ISA是：Industry Standard Architecture（工业标准体系结构）IDE是 （Integrated Device Electronics）集成电路设备简称PIIX4PIIX4器件（芯片）的特点1、是一种支持Pentium和PentiumII微处理器的部件。2、82371对ISA桥来说，是一种多功能PCI总线。3、对可移动性和桌面深绿色环境均提供支持。4、电源管理逻辑。5、被集成化的IDE控制器。6、增强了性能的DMA控制器。 （7）基于两个82C59的中断控制器。（8）基于82C54芯片的定时器。（9）USB（Universal Serial Bus）通用串行总线。（10）SMBus系统管理总线。（11）实时时钟（12）顺应Microsoft Win95所需的功能其芯片的逻辑框图如图6-1所示。 PIIX4芯片逻辑框图6.1.1 概述PIIX4芯片是一个多功能的PCI器件，图6-2 是82371在系统中扮演的角色。（续上图）1. PCI与EIO之间的桥（PIIX4芯片）桥是不对程的，是各类不同标准总线与PCI总线连接，82371AB桥也可理解为一种总线转换译码器和控制器，桥内包含复杂的协议总线信号和缓冲器。(1).在PCI系统内，当PIIX4操作时，它总是作为系统内各种模块的主控设备，如USB和DMA控制器、IDE总线和分布式DMA的主控设备等，而且总是以ISA主控设备的名义出现。(2). 在向ISA总线或IDE总线进行传送操作的传送周期期间作为从属设备使用，并对内部寄存器译码。PIIX4芯片（桥）的配置(1).可以把PIIX4芯片配置成整个ISA总线，或ISA总线的子集，也可扩展成EIO总线。在使用EIO总线时，可以把未使用的信号配置成通用的输入和输出。(2).PIIX4可直接驱动5个ISA插槽；(3).能提供字节-交换逻辑、I/O的恢复支持、等待状态的生成以及SYSCLK的生成。(4).提供X-BUS键盘控制器芯片、BIOS芯片、实时时钟芯片、二级微程序器等的选择。2. IDE接口（总线主控设备的权利和同步DMA方式）IDE接口为4个IDE的设备提供支持，比如IDE接口的硬盘和CD-ROM等。注意：目前硬盘接口有5类：IDE、SCSI、Fibre Channel、IEEE1394和USB等。IDE口几乎在PC机最多，因为便宜。SCSI多用于服务器和集群机。IDE的PIO IDE速率：14MB/s；而总线主控设备IDE的速率：33MB/s在PIIX4芯片的IDE系统内，配有两个各次独立的IDE信号通道。3. 具有兼容性的模块—DMA、定时器/计数器、中断控制器等（1）在PIIX4内的两各82C37 DMA控制器经逻辑的组合，产生7个独立的可编程通道。通道[0：3]是通过与8个二进位的硬件连线实现的。通过以字节为单位的计数进行传送。而通道[5：7]是通过16个二进位的连线实现的，以字为单位的计数进行传送。（2）DMA控制器还能通过PCI总线，处理旧的DMA的两个不同的方法提供支持。（3）计数/定时器模块在功能上与82C54等价。（4）中断控制器与ISA兼容，其功能是两个82C59的功能之和。
上传时间： 2013-11-19
上传用户：3到15
一种实用的微机自动配料秤系统:介绍一种由单片机构成的配料秤。叙述了秤的传感器、变送器、信号的变换、硬件原理、软件流程以及和DCS 系统构成的单回路调节系统,此系统可广泛地应用于各行业的配料控制中。关键词:配料秤 单片机 单回路调节系统 DCS 系统 Abstract :A proportioning weigher based on single chip computer is introduced. Sensors , transmitters , signal converting , principle of hardware ,software flowchart of proportioning weigher and single loop control system composed with DCS system are emphasized ,this system can be used in proportioning control of various trades extensively.Key Words :Proportioning Weigher ,Single Chip Computer ,Single Loop Control System ,Distributed Control System
上传时间： 2013-10-12
上传用户：zwei41
The Motorola MPC106 PCI bridge/memory controller provides a PowerPCªmicroprocessor common hardware reference platform (CHRPª) compliant bridgebetween the PowerPC microprocessor family and the Peripheral Component Interconnect(PCI) bus. In this document, the term Ô106Õ is used as an abbreviation for the phraseÔMPC106 PCI bridge/memory controllerÕ. This document contains pertinent physicalcharacteristics of the 106. For functional characteristics refer to theMPC106 PCI Bridge/Memory Controller UserÕs Manual.This document contains the following topics:Topic PageSection 1.1, ÒOverviewÓ 2Section 1.2, ÒFeaturesÓ 3Section 1.3, ÒGeneral ParametersÓ 5Section 1.4, ÒElectrical and Thermal CharacteristicsÓ 5Section 1.5, ÒPin AssignmentsÓ 17Section 1.6, ÒPinout Listings 18Section 1.7, ÒPackage DescriptionÓ 22Section 1.8, ÒSystem Design InformationÓ 24Section 1.9, ÒDocument Revision HistoryÓ 29Section 1.10, ÒOrdering InformationÓ 29
上传时间： 2013-11-04
上传用户：as275944189
The μPSD32xx family, from ST, consists of Flash programmable system devices with a 8032 MicrocontrollerCore. Of these, the μPSD3234A and μPSD3254A are notable for having a complete implementationof the USB hardware directly on the chip, complying with the Universal Serial Bus Specification, Revision1.1.This application note describes a demonstration program that has been written for the DK3200 hardwaredemonstration kit (incorporating a μPSD3234A device). It gives the user an idea of how simple it is to workwith the device, using the HID class as a ready-made device driver for the USB connection.IN-APPLICATION-PROGRAMMING (IAP) AND IN-SYSTEM-PROGRAMMING (ISP)Since the μPSD contains two independent Flash memory arrays, the Micro Controller Unit (MCU) can executecode from one memory while erasing and programming the other. Product firmware updates in thefield can be reliably performed over any communication channel (such as CAN, Ethernet, UART, J1850)using this unique architecture. For In-Application-Programming (IAP), all code is updated through theMCU. The main advantage for the user is that the firmware can be updated remotely. The target applicationruns and takes care on its own program code and data memory.IAP is not the only method to program the firmware in μPSD devices. They can also be programmed usingIn-System-Programming (ISP). A IEEE1149.1-compliant JTAG interface is included on the μPSD. Withthis, the entire device can be rapidly programmed while soldered to the circuit board (Main Flash memory,Secondary Boot Flash memory, the PLD, and all configuration areas). This requires no MCU participation.The MCU is completely bypassed. So, the μPSD can be programmed or reprogrammed any time, anywhere, even when completely uncommitted.Both methods take place with the device in its normal hardware environment, soldered to a printed circuitboard. The IAP method cannot be used without previous use of ISP, because IAP utilizes a small amountof resident code to receive the service commands, and to perform the desired operations.
标签： Demonstration 3200 USB for
上传时间： 2014-02-27
上传用户：zhangzhenyu
The μPSD32xx family, from ST, consists of Flash programmable system devices with a 8032 Microcontroller Core. Of these, the μPSD3234A and μPSD3254A are notable for having a complete implementation of the USB hardware directly on the chip, complying with the Universal Serial Bus Specification, Revision 1.1.This application note describes a demonstration program that has been written for the DK3200 hardware demonstration kit (incorporating a μPSD3234A device). It gives the user an idea of how simple it is to work with the device, using the HID class as a ready-made device driver for the USB connection.
上传时间： 2014-04-03
上传用户：lizhizheng88
Internal Interrupts are used to respond to asynchronous requests from a certain part of themicrocontroller that needs to be serviced. Each peripheral in the TriCore as well as theBus Control Unit, the Debug Unit, the Peripheral Control Processor (PCP) and the CPUitself can generate an Interrupt Request.So what is an external Interrupt?An external Interrupt is something alike as the internal Interrupt. The difference is that anexternal Interrupt request is caused by an external event. Normally this would be a pulseon Port0 or Port1, but it can be even a signal from the input buffer of the SSC, indicatingthat a service is requested.The User’s Manual does not explain this aspect in detail so this ApNote will explain themost common form of an external Interrupt request. This ApNote will show that there is aneasy way to react on a pulse on Port0 or Port1 and to create with this impulse an InterruptService Request. Later in the second part of the document, you can find hints on how todebounce impulses to enable the use of a simple switch as the input device.Note: You will find additional information on how to setup the Interrupt System in theApNote “First steps through the TriCore Interrupt System” (AP3222xx)1. It would gobeyond the scope of this document to explain this here, but you will find selfexplanatoryexamples later on.
上传时间： 2013-10-27
上传用户：zhangyigenius
This application note shows how to write an Inter Integrated Circuit bus driver (I²C) for the Philips P90CL301micro-controller.It is not only an example of writing a driver, but it also includes a set of application interface software routines toquickly implement a complete I²C multi-master system application.For specific applications the user will have to make minimal changes in the driver program. Using the drivermeans linking modules to your application software and including a header-file into the application sourceprograms. A small example program of how to use the driver is listed.The driver supports i.a. polled or interrupt driven message handling, slave message transfers and multi-mastersystem applications. Furthermore, it is made suitable for use in conjunction with real time operating systems, likepSOS+.
上传时间： 2013-11-23
上传用户：weixiao99
The P90CL301 is a highly integrated 16/32 bit micro-controller especially suitable for applications requiring lowvoltage and low power consumption. It is fully software compatible with the 68000. Furthermore, it provides bothstandard as well as advanced peripheral functions on-chip.One of these peripheral functions is the I2C bus. This report describes worked-out driver software (written in C) toprogram the P90CL301 I2C interface. It also contains interface software routines offering the user a quick start inwriting a complete I2C system application.
上传时间： 2014-01-06
上传用户：气温达上千万的
