Industrial remote monitoring systems and keep-alivecircuits spend most of their time in standby mode. Manyof these systems also depend on battery power, so powersupply effi ciency in standby state is very important tomaximize battery life. The LT®8410/-1 high effi ciencyboost converter is ideal for these systems, requiringonly 8.5μA of quiescent current in standby mode. Thedevice integrates high value (12.4M/0.4M) output feedbackresistors, signifi cantly reducing input current whenthe output is in regulation with no load. Other featuresinclude an integrated 40V switch and Schottky diode,output disconnect with current limit, built in soft-start,overvoltage protection and a wide input range, all in atiny 8-pin 2mm × 2mm DFN package.
上传时间： 2013-11-23
上传用户：新手无忧
Linear Technology’s DC/DC step-down μModule®regulators are complete switchmode power supplies in asurface-mount package. They include the DC/DC controller,inductor, power switches and supporting circuitry.These highly integrated regulators also provide an easysolution for applications that require negative outputvoltages. In other words, these products can operate asinverting buck-boost regulators. As a result, the lowestpotential in the circuit is not the standard 0V, but –VOUT,which must be tied to the μModule regulator’s GND. Allsignals are now referred to –VOUT.
上传时间： 2013-10-22
上传用户：ztj182002
Once relegated to the hinterlands of low cost indicatorlights, the LED is again in the spotlight of the lightingworld. LED lighting is now ubiquitous, from car headlightsto USB-powered lava lamps. Car headlights exemplifyapplications that capitalize on the LED’s clear advantages—unwavering high quality light output, tough-assteelrobustness, inherent high effi ciency—while a USBlava lamp exemplifi es applications where only LEDs work.Despite these clear advantages, their requirement forregulated voltage and current make LED driver circuitsmore complex than the venerable light bulb, but some newdevices are closing the gap. For instance, the LTM®8040μModule™ LED driver integrates all the driver circuitryinto a single package, allowing designers to refocus theirtime and effort on the details of lighting design criticalto a product’s success.
上传时间： 2013-10-16
上传用户：togetsomething
The LTM4601 DC/DC μModule regulator is a completehigh power density stepdown regulator for up to 12Acontinuous (14A peak) loads. The device is housed ina small 15mm ¥ 15mm ¥ 2.8mm LGA surface mountpackage, thus the large power dissipation is a challengein some applications. This thermal application note willprovide guidelines for using the μModule regulator inambient environments with or without air fl ow. Loadcurrent derating curves are provided for several inputvoltages and output voltages versus ambient temperatureand air fl ow.
上传时间： 2013-10-19
上传用户：bakdesec
The LTM4600 DC/DC μModule regulator is a complete highpower density stepdown regulator for 10A continuous (14Apeak) loads. The device has two voltage options: 20VINmaximum for the LTM4600EV and 28VIN maximum for theLTM4600HVEV each housed in a small 15mm ¥ 15mm ¥2.8mm LGA surface mount package.
上传时间： 2013-10-10
上传用户：adada
The LTM8020, LTM8021, LTM8022 and LTM8023 μModule®regulators are complete easy-to-use encapsulated stepdownDC/DC regulators intended to take the pain and aggravationout of implementing a switching power supplyonto a system board. With a μModule regulator, you onlyneed an input cap, output cap and one or two resistorsto complete the design. As one might imagine, this highlevel of integration greatly simplifi es the task of printedcircuit board design, reducing the effort to four categories:component footprint generation, component placement,routing the nets, and thermal vias.
上传时间： 2014-01-18
上传用户：laomv123
38V/100A可直接并联大功率AC/DC变换器 随着电力电子技术的发展，电源技术被广泛应用于计算机、工业仪器仪表、军事、航天等领域，涉及到国民经济各行各业。特别是近年来，随着IGBT的广泛应用，开关电源向更大功率方向发展。研制各种各样的大功率，高性能的开关电源成为趋势。某电源系统要求输入电压为AC220V，输出电压为DC38V，输出电流为100A，输出电压低纹波，功率因数>0.9，必要时多台电源可以直接并联使用，并联时的负载不均衡度<5％。 设计采用了AC/DC/AC/DC变换方案。一次整流后的直流电压，经过有源功率因数校正环节以提高系统的功率因数，再经半桥变换电路逆变后，由高频变压器隔离降压，最后整流输出直流电压。系统的主要环节有DC/DC电路、功率因数校正电路、PWM控制电路、均流电路和保护电路等。 1 有源功率因数校正环节 由于系统的功率因数要求0.9以上，采用二极管整流是不能满足要求的，所以，加入了有源功率因数校正环节。采用UC3854A/B控制芯片来组成功率因数电路。UC3854A/B是Unitrode公司一种新的高功率因数校正器集成控制电路芯片，是在UC3854基础上的改进。其特点是：采用平均电流控制，功率因数接近1，高带宽，限制电网电流失真≤3％[1]。图1是由UC3854A/B控制的有源功率因数校正电路。 该电路由两部分组成。UC3854A/B及外围元器件构成控制部分，实现对网侧输入电流和输出电压的控制。功率部分由L2，C5，V等元器件构成Boost升压电路。开关管V选择西门康公司的SKM75GB123D模块，其工作频率选在35kHz。升压电感L2为2mH/20A。C5采用四个450V/470μF的电解电容并联。因为，设计的PFC电路主要是用在大功率DC/DC电路中，所以，在负载轻的时候不进行功率因数校正，当负载较大时功率因数校正电路自动投入使用。此部分控制由图1中的比较器部分来实现。R10及R11是负载检测电阻。当负载较轻时，R10及R11上检测的信号输入给比较器，使其输出端为低电平，D2导通，给ENA(使能端)低电平使UC3854A/B封锁。在负载较大时ENA为高电平才让UC3854A/B工作。D3接到SS（软启动端），在负载轻时D3导通，使SS为低电平；当负载增大要求UC3854A/B工作时，SS端电位从零缓慢升高，控制输出脉冲占空比慢慢增大实现软启动。 2 DC/DC主电路及控制部分分析 2.1 DC/DC主电路拓扑 在大功率高频开关电源中，常用的主变换电路有推挽电路、半桥电路、全桥电路等[2]。其中推挽电路的开关器件少，输出功率大，但开关管承受电压高（为电源电压的2倍），且变压器有六个抽头，结构复杂；全桥电路开关管承受的电压不高，输出功率大，但是需要的开关器件多（4个），驱动电路复杂。半桥电路开关管承受的电压低，开关器件少，驱动简单。根据对各种拓扑方案的工程化实现难度，电气性能以及成本等指标的综合比较，本电源选用半桥式DC/DC变换器作为主电路。图2为大功率开关电源的主电路拓扑图。
上传时间： 2013-11-13
上传用户：ukuk
针对广泛使用电池供电的系统，由于电源电压监控的要求，系统复位电路的可靠性对整个系统的稳定性起着非常重要的作用，本文研究并设计一种低功耗，高性能的复位芯片，可以在系统上电，掉电的情况下向微处理器提供复位信号。当电源电压低于预设的门槛电压时，输出复位信号并在电源电压恢复到门槛电压以上继续持续复位一段时间，实现整个系统的平稳恢复，复位信号低电平有效。该芯片采用CMSC035标准CMOS工艺实现，采用Cadence Spectre仿真，工作电流仅为10 μA。该芯片已成功应用于工业类控制系统中。
上传时间： 2014-12-24
上传用户：Late_Li
μPSD3200系列中文资料
上传时间： 2013-10-24
上传用户：xiaohanhaowei
设计了一个基于单片机的轿车车内一氧化碳浓度测控功能的系统。该系统以16位高性能单片机SPCE061A为控制核心，采用高精度敏感元件MQ-7，集成运算放大器INA128进行信号调理，并引入了实时操作系统μC/OS-II进行任务管理。实验表明：系统实现了轿车空调运行时一氧化碳气体的实时监控，CO浓度不超过300 ppm，同时具有温度测量功能，便于进行空调操作，参数测量准确，为保证轿车内人员安全提供了可靠方案。
上传时间： 2013-12-04
上传用户：缥缈
