This application note describes a Linear Technology "Half-Flash" A/D converter, the LTC1099, being connected to a 256 element line scan photodiode array. This technology adapts itself to handheld (i.e., low power) bar code readers, as well as high resolution automated machine inspection applications..
上传时间： 2013-11-21
上传用户：lchjng
Low power operation of electronic apparatus has becomeincreasingly desirable. Medical, remote data acquisition,power monitoring and other applications are good candidatesfor battery driven, low power operation. Micropoweranalog circuits for transducer-based signal conditioningpresent a special class of problems. Although micropowerICs are available, the interconnection of these devices toform a functioning micropower circuit requires care. (SeeBox Sections, “Some Guidelines for Micropower Designand an Example” and “Parasitic Effects of Test Equipmenton Micropower Circuits.”) In particular, trade-offs betweensignal levels and power dissipation become painful whenperformance in the 10-bit to 12-bit area is desirable.
上传时间： 2013-10-22
上传用户：rocketrevenge
ANALOG INPUT BANDWIDTH is a measure of the frequencyat which the reconstructed output fundamental drops3 dB below its low frequency value for a full scale input. Thetest is performed with fIN equal to 100 kHz plus integer multiplesof fCLK. The input frequency at which the output is −3dB relative to the low frequency input signal is the full powerbandwidth.APERTURE JITTER is the variation in aperture delay fromsample to sample. Aperture jitter shows up as input noise.APERTURE DELAY See Sampling Delay.BOTTOM OFFSET is the difference between the input voltagethat just causes the output code to transition to the firstcode and the negative reference voltage. Bottom Offset isdefined as EOB = VZT–VRB, where VZT is the first code transitioninput voltage and VRB is the lower reference voltage.Note that this is different from the normal Zero Scale Error.CONVERSION LATENCY See PIPELINE DELAY.CONVERSION TIME is the time required for a completemeasurement by an analog-to-digital converter. Since theConversion Time does not include acquisition time, multiplexerset up time, or other elements of a complete conversioncycle, the conversion time may be less than theThroughput Time.DC COMMON-MODE ERROR is a specification which appliesto ADCs with differential inputs. It is the change in theoutput code that occurs when the analog voltages on the twoinputs are changed by an equal amount. It is usually expressed in LSBs.
上传时间： 2013-11-12
上传用户：pans0ul
Radio Frequency Integrated Circuit Design I enjoyed reading this book for a number of reasons. One reason is that itaddresses high-speed analog design in the context of microwave issues. This isan advanced-level book, which should follow courses in basic circuits andtransmission lines. Most analog integrated circuit designers in the past workedon applications at low enough frequency that microwave issues did not arise.As a consequence, they were adept at lumped parameter circuits and often notcomfortable with circuits where waves travel in space. However, in order todesign radio frequency (RF) communications integrated circuits (IC) in thegigahertz range, one must deal with transmission lines at chip interfaces andwhere interconnections on chip are far apart. Also, impedance matching isaddressed, which is a topic that arises most often in microwave circuits. In mycareer, there has been a gap in comprehension between analog low-frequencydesigners and microwave designers. Often, similar issues were dealt with in twodifferent languages. Although this book is more firmly based in lumped-elementanalog circuit design, it is nice to see that microwave knowledge is brought inwhere necessary.Too many analog circuit books in the past have concentrated first on thecircuit side rather than on basic theory behind their application in communications.The circuits usually used have evolved through experience, without asatisfying intellectual theme in describing them. Why a given circuit works bestcan be subtle, and often these circuits are chosen only through experience. Forthis reason, I am happy that the book begins first with topics that require anintellectual approach—noise, linearity and filtering, and technology issues. Iam particularly happy with how linearity is introduced (power series). In therest of the book it is then shown, with specific circuits and numerical examples,how linearity and noise issues arise.
上传时间： 2014-12-23
上传用户：han_zh
磁芯电感器的谐波失真分析 摘 要：简述了改进铁氧体软磁材料比损耗系数和磁滞常数ηB，从而降低总谐波失真THD的历史过程，分析了诸多因数对谐波测量的影响，提出了磁心性能的调控方向。 关键词：比损耗系数， 磁滞常数ηB ，直流偏置特性DC-Bias，总谐波失真THD Analysis on THD of the fer rite co res u se d i n i nductancShi Yan Nanjing Finemag Technology Co. Ltd., Nanjing 210033 Abstract: Histrory of decreasing THD by improving the ratio loss coefficient and hysteresis constant of soft magnetic ferrite is briefly narrated. The effect of many factors which affect the harmonic wave testing is analysed. The way of improving the performance of ferrite cores is put forward. Key words: ratio loss coefficient，hysteresis constant，DC-Bias，THD 近年来，变压器生产厂家和软磁铁氧体生产厂家，在电感器和变压器产品的总谐波失真指标控制上，进行了深入的探讨和广泛的合作，逐步弄清了一些似是而非的问题。从工艺技术上采取了不少有效措施，促进了质量问题的迅速解决。本文将就此热门话题作一些粗浅探讨。 一、 历史回顾 总谐波失真（Total harmonic distortion） ，简称THD，并不是什么新的概念，早在几十年前的载波通信技术中就已有严格要求<1>。1978年邮电部公布的标准YD/Z17－78“载波用铁氧体罐形磁心”中，规定了高μQ材料制作的无中心柱配对罐形磁心详细的测试电路和方法。如图一电路所示，利用LC组成的150KHz低通滤波器在高电平输入的情况下测量磁心产生的非线性失真。这种相对比较的实用方法，专用于无中心柱配对罐形磁心的谐波衰耗测试。 这种磁心主要用于载波电报、电话设备的遥测振荡器和线路放大器系统，其非线性失真有很严格的要求。 图中 ZD —— QF867 型阻容式载频振荡器，输出阻抗 150Ω， Ld47 —— 47KHz 低通滤波器，阻抗 150Ω，阻带衰耗大于61dB， Lg88 ——并联高低通滤波器，阻抗 150Ω，三次谐波衰耗大于61dB Ld88 ——并联高低通滤波器，阻抗 150Ω，三次谐波衰耗大于61dB FD —— 30～50KHz 放大器， 阻抗 150Ω， 增益不小于 43 dB，三次谐波衰耗b3(0)≥91 dB, DP —— Qp373 选频电平表，输入高阻抗， L ——被测无心罐形磁心及线圈， C ——聚苯乙烯薄膜电容器CMO-100V-707APF±0.5%,二只。 测量时，所配用线圈应用丝包铜电磁线SQJ9×0.12(JB661-75)在直径为16.1mm的线架上绕制 120 匝， （线架为一格） ， 其空心电感值为 318μH（误差1％） 被测磁心配对安装好后，先调节振荡器频率为 36.6～40KHz， 使输出电平值为+17.4 dB， 即选频表在 22′端子测得的主波电平 （P2）为+17.4 dB，然后在33′端子处测得输出的三次谐波电平（P3）， 则三次谐波衰耗值为：b3(+2)= P2+S+ P3 式中：S 为放大器增益dB 从以往的资料引证， 就可以发现谐波失真的测量是一项很精细的工作，其中测量系统的高、低通滤波器，信号源和放大器本身的三次谐波衰耗控制很严，阻抗必须匹配，薄膜电容器的非线性也有相应要求。滤波器的电感全由不带任何磁介质的大空心线圈绕成，以保证本身的“洁净” ，不至于造成对磁心分选的误判。 为了满足多路通信整机的小型化和稳定性要求， 必须生产低损耗高稳定磁心。上世纪 70 年代初，1409 所和四机部、邮电部各厂，从工艺上改变了推板空气窑烧结，出窑后经真空罐冷却的落后方式，改用真空炉，并控制烧结、冷却气氛。技术上采用共沉淀法攻关试制出了μQ乘积 60 万和 100 万的低损耗高稳定材料，在此基础上，还实现了高μ7000～10000材料的突破，从而大大缩短了与国外企业的技术差异。当时正处于通信技术由FDM（频率划分调制）向PCM（脉冲编码调制） 转换时期， 日本人明石雅夫发表了μQ乘积125 万为 0.8×10 ，100KHz）的超优铁氧体材料<3>，其磁滞系数降为优铁
上传时间： 2014-12-24
上传用户：7891
This document provides practical, common guidelines for incorporating PCI Express interconnect layouts onto Printed Circuit Boards (PCB) ranging from 4-layer desktop baseboard designs to 10- layer or more server baseboard designs. Guidelines and constraints in this document are intended for use on both baseboard and add-in card PCB designs. This includes interconnects between PCI Express devices located on the same baseboard (chip-to-chip routing) and interconnects between a PCI Express device located “down” on the baseboard and a device located “up” on an add-in card attached through a connector. This document is intended to cover all major components of the physical interconnect including design guidelines for the PCB traces, vias and AC coupling capacitors, as well as add-in card edge-finger and connector considerations. The intent of the guidelines and examples is to help ensure that good high-speed signal design practices are used and that the timing/jitter and loss/attenuation budgets can also be met from end-to-end across the PCI Express interconnect. However, while general physical guidelines and suggestions are given, they may not necessarily guarantee adequate performance of the interconnect for all layouts and implementations. Therefore, designers should consider modeling and simulation of the interconnect in order to ensure compliance to all applicable specifications. The document is composed of two main sections. The first section provides an overview of general topology and interconnect guidelines. The second section concentrates on physical layout constraints where bulleted items at the beginning of a topic highlight important constraints, while the narrative that follows offers additional insight.
上传时间： 2013-10-15
上传用户：busterman
Abstract: There are differences between the operation of low-frequency AC transformers and electronic transformersthat supply current to MR16 lamps, and there are also differences in the current draw for MR16 halogen lamps andMR16 LED lamps. These contrasts typically prevent an MR16 LED lamp from operating with most electronictransformers. This article explains how a high-brightness (HB) LED driver optimized for MR16 lamps will allow LEDlamps to be compatible with most electronic transformers.A similar version of this article appeared on Display Plus, July 7, 2012 and in German in Elektronikpraxis, October 1,2012.
上传时间： 2013-10-14
上传用户：playboys0
A light-emitting diode (LED) is a semiconductor device that emits narrow-spectrum incoherent light when forward-biased.The color of the emitted light depends on the chemical composition of the semiconductor material used, and can benear-ultraviolet, visible or infrared. LEDs are more prevalent today than ever before, replacing traditional incandescent andfluorescent bulbs in many lighting applications. Incandescents use a heated filament, are subject to breakage and burnoutand operate at a luminous efficiency of 2% to 4%. Fluorescents are more efficient, at 7% to 12%, but require highdrive voltage and contain mercury, a toxic substance that may be eventually banned in certain countries. LEDs, however,produce light directly through electroluminescence, operate at low voltage and can deliver over 20% luminous efficiency.
上传时间： 2013-11-07
上传用户：xiaoyuer
Abstract: We don't expect manufacturers to produce clothes that in one size that fits everyone. In thesame way, one ESD component can't solve all issues—each application has different ESD requirements.Knowing that "one size fits all" cannot apply to power design, the power designer, or the engineering"super hero," must consider all the potential disruptions to a steady flow of power and thenvarious waysto mitigate them. This tutorial describes voltage- and current-limiting devices and risetime reducers tomanage the power. It also points to free and low-cost software tools to help design lowpass filters, checkcapacitor self-resonance, and simulate circuits.
上传时间： 2013-11-18
上传用户：zhouxuepeng1
Abstract: Impedance mismatches in a radio-frequency (RF) electrical transmission line cause power loss andreflected energy. Voltage standing wave ratio (VSWR) is a way to measure transmission line imperfections. Thistutorial defines VSWR and explains how it is calculated. Finally, an antenna VSWR monitoring system is shown.
上传时间： 2013-10-19
上传用户：yuanwenjiao
