Luminary Micro provides an analog-to-digital converter (ADC) module on some members of theStellaris microcontroller family. The hardware resolution of the ADC is 10 bits; however, due to noiseand other accuracy-diminishing factors, the true accuracy is less than 10 bits. This application noteprovides a software-based oversampling technique, resulting in an improved Effective Number OfBits (ENOB) in the conversion result. This document describes methods of oversampling an inputsignal, and the impact on precision and overall system performance.
标签： Oversampling Techniques ADC fo
上传时间： 2013-12-17
上传用户：zhyiroy
Luminary Micro Stellaris™ microcontrollers that are equipped with an analog-to-digital converter(ADC), use an innovative sequence-based sampling architecture designed to be extremely flexible,yet easy to use. This application note describes the sampling architecture of the ADC. Sinceprogrammers can configure Stellaris microcontrollers either through the powerful StellarisFamilyDriver Library or through direct writes to the device's control registers, this application note describesboth methods. The information presented in this document is intended to complement the ADCchapter of the device datasheet, and assumes the reader has a basic understanding of howADCsfunction.
标签： Microcontr Stellaris Using the
上传时间： 2013-10-14
上传用户：blans
The MAX3243E device consists of three line drivers, five line receivers, and a dual charge-pump circuit with±15-kV ESD (HBM and IEC61000-4-2, Air-Gap Discharge) and ±8-kV ESD (IEC61000-4-2, Contact Discharge)protection on serial-port connection pins. The device meets the requirements of TIA/EIA-232-F and provides theelectrical interface between an asynchronous communication controller and the serial-port connector. Thiscombination of drivers and receivers matches that needed for the typical serial port used in an IBM PC/AT, orcompatible. The charge pump and four small external capacitors allow operation from a single 3-V to 5.5-Vsupply. In addition, the device includes an always-active noninverting output (ROUT2B), which allowsapplications using the ring indicator to transmit data while the device is powered down. The device operates atdata signaling rates up to 250 kbit/s and a maximum of 30-V/ms driver output slew rate.
标签： MULTICHANNEL 5.5 TO RS
上传时间： 2013-10-19
上传用户：ddddddd
高压双管反激变换器的设计:介绍一种双管反激的电路拓扑，分析了其工作原理，给出了一些关键技术参数的计算公式，设计并研制成功的30W 380V AC5 0H z/510V DC/+15.1 V DC(1A )、+5.2VDC(2A)辅助开关电源具有功率密度高、变换效率高、可靠性高等优良的综合性能。该变换器在高电压输人情况下有重要的应用价值。【关 键 词 】变换器，辅助开关电源，双管反激 [Abstract】 A n e wt opologyfo rd oubles witchfl ybackc onverteris in troduced.Th eo perationp rincipleis a nalyzeda nds ome for mulas for calculating key parameters for the topology are presented. The designed and produced auxiliary switching power supply,i. e. 30W 380V AC5 0H z/5 10V DC/+15.1 V DC《1A )、+5.2 V DC《2A )，hase xcellentc omprehensivep erformances sucha sh ighp owerd ensity, hi ghc onversione fficiencya ndh ighr eliability.Th isc onverterh asim portanta pplicationv aluef orh igh input voltag [Keywords ]converter,au xiliary switchingp owers upply,do ubles witchf lybac
上传时间： 2013-11-01
上传用户：Ants
The MC68HC05K0 is a low cost, low pin countsingle chip microcomputer with 504 bytes of userROM and 32 bytes of RAM. The MC68HC05K0 isa member of the 68HC05K series of devices whichare available in 16-pin DIL or SOIC packages.It uses the same CPU as the other devices in the68HC05 family and has the same instructions andregisters. Additionally, the device has a 15-stagemulti-function timer and 10 general purposebi-directional I/0 lines. A mask option is availablefor software programmable pull-downs on all ofthe I/O pins and four of the pins are capable ofgenerating interrupts.The device is ideally suited for remote-controlkeyboard applications because the pull-downs andthe interrupt drivers on the port pins allowkeyboards to be built without any externalcomponents except the keys themselves. There isno need for external pull-up or pull-down resistors,or diodes for wired-OR interrupts, as these featuresare already designed into the device.
上传时间： 2014-01-24
上传用户：zl5712176
The STWD100 watchdog timer circuits are self-contained devices which prevent systemfailures that are caused by certain types of hardware errors (non-responding peripherals,bus contention, etc.) or software errors (bad code jump, code stuck in loop, etc.).The STWD100 watchdog timer has an input, WDI, and an output, WDO (see Figure 2). Theinput is used to clear the internal watchdog timer periodically within the specified timeoutperiod, twd (see Section 3: Watchdog timing). While the system is operating correctly, itperiodically toggles the watchdog input, WDI. If the system fails, the watchdog timer is notreset, a system alert is generated and the watchdog output, WDO, is asserted (seeSection 3: Watchdog timing).The STWD100 circuit also has an enable pin, EN (see Figure 2), which can enable ordisable the watchdog functionality. The EN pin is connected to the internal pull-downresistor. The device is enabled if the EN pin is left floating.
上传时间： 2013-10-22
上传用户：taiyang250072
（Portmon is an application that lets you monitor serial and parallel activity on your local system, or any computer on the network that you can reach via TCP/IP. It is the most powerful tool available for tracking down port-related configuration problems and analyzing application port usage.）
上传时间： 2013-11-07
上传用户：1412904892
Introduction to Xilinx Packaging Electronic packages are interconnectable housings for semiconductor devices. The major functions of the electronic packages are to provide electrical interconnections between the IC and the board and to efficiently remove heat generated by the device. Feature sizes are constantly shrinking, resulting in increased number of transistors being packed into the device. Today's submicron technology is also enabling large-scale functional integration and system-on-a-chip solutions. In order to keep pace with these new advancements in silicon technologies, semiconductor packages have also evolved to provide improved device functionality and performance. Feature size at the device level is driving package feature sizes down to the design rules of the early transistors. To meet these demands, electronic packages must be flexible to address high pin counts, reduced pitch and form factor requirements. At the same time,packages must be reliable and cost effective.
上传时间： 2013-10-22
上传用户：ztj182002
特点 最高輸入頻率 10KHz 显示范围0-9999（一段设定）0至999999累积量 计数速度 50/10000脈波/秒可选择 输入脈波具有预设刻度功能 累积量同步（批量）或非同步（批次）计数可选择 数位化指拨设定操作简易 计数暂时停止功能 1组报警功能 2:主要規格 脈波輸入型式: Jump-pin selectable current sourcing(NPN) or current sinking (PNP) 脉波触发电位: HI bias (CMOS) (VIH=7.5V, VIL=5.5V) LO bias (TTL) (VIH=3.7V, VIL=2.0V) 最高输入频率: <10KHz (up,down,up/down mode) 输出动作时间 : 0.1 to 99.9 second adjustable 输出复归方式: Manual(N) or automatic (R or C) can be modif 继电器容量: AC 250V-5A, DC 30V-7A 显示值范围: 0-9999（PV,SV） 0-999999(TV) 显示幕: Red high efficiency LEDs high 7.0mm (.276")(PV,SV) Red high efficiency LEDs high 9.2mm (.36")(TV) 参数设定方式: Touch switches 感应器电源: 12VDC +/-3%(<60mA) 记忆方式: Non-volatile E2PROM memory 绝缘耐压能力: 2KVac/1 min. (input/output/power) 1600Vdc (input/output) 使用环境条件: 0-50℃(20 to 90% RH non-condensed) 存放环境条件: 0-70℃(20 to 90% RH non-condensed) CE认证: EN 55022:1998/A1:2000 Class A EN 61000-3-2:2000 EN 61000-3-3:1995/A1:2001 EN 55024:1998/A1:2001
上传时间： 2013-10-24
上传用户：wvbxj
特点 最高輸入頻率 10KHz 计数速度 50/10000脈波/秒可选择 四种输入模式可选择(加算,減算,加減算,90度相位差加減算) 90度相位差加減算具有提高解析度4倍功能 输入脈波具有预设刻度功能 计数暂时停止功能 3组报警功能 15BIT类比输出功能 数位RS-485界面 2:主要規格 脈波輸入型式: Jump-pin selectable current sourcing(NPN) or current sinking (PNP) 脉波触发电位: HI bias (CMOS) (VIH=7.5V, VIL=5.5V) LO bias (TTL) (VIH=3.7V, VIL=2.0V) 最高输入频率: <10KHz (up,down,up/down mode) <3KHz (quadrature mode) 输出动作时间 : 0.1 to 99.9 second adjustable 输出复归方式: Manual(N) or automatic (R or C) can be modif 继电器容量: AC 250V-5A, DC 30V-7A 显示值范围: -199999 to 999999 类比输出解析度: 15 bit DAC 输出反应速度: < 1/f+10ms(0-90%) 输出负载能力: < 10mA for voltage mode < 10V for current mode <[(V+)-7.5V]/20mA for two-wire mode 输出之涟波: < 0.1% F.S. 通讯位址: "01"-"FF" 传输速度: 19200/9600/4800/2400 selective 通信协议: Modbus RTU mode 显示幕: Red high efficiency LEDs high 14.22mm (.56") 参数设定方式: Touch switches 感应器电源: 12VDC +/-3%(<60mA) 记忆方式: Non-volatile E2PROM memory 绝缘耐压能力: 2KVac/1 min. (input/output/power) 1600Vdc (input/output) 使用环境条件: 0-50℃(20 to 90% RH non-condensed) 存放环境条件: 0-70℃(20 to 90% RH non-condensed) CE认证: EN 55022:1998/A1:2000 Class A EN 61000-3-2:2000 EN 61000-3-3:1995/A1:2001 EN 55024:1998/A1:2001
上传时间： 2013-11-23
上传用户：redmoons
