The LTC®3610 is a high power monolithic synchronousstep-down DC/DC regulator that can deliver up to 12Aof continuous output current from a 4V to 24V (28Vmaximum) input supply. It is a member of a high currentmonolithic regulator family (see Table 1) that featuresintegrated low RDS(ON) N-channel top and bottomMOSFETs. This results in a high effi ciency and highpower density solution with few external components.This regulator family uses a constant on-time valleycurrent mode architecture that is capable of operatingat very low duty cycles at high frequency and with veryfast transient response. All are available in low profi le(0.9mm max) QFN packages.
上传时间： 2013-11-07
上传用户：moerwang
High voltage buck DC/DC controllers such as the LTC3890(dual output) and LTC3891 (single output) are popular inautomotive applications due to their extremely wide 4V to60V input voltage range, eliminating the need for a snubberand voltage suppression circuitry. These controllersare also well suited for 48V telecom applications whereno galvanic isolation is required.
上传时间： 2013-10-31
上传用户：wwwe
A recent trend in the design of portable devices has beento use ceramic capacitors to filter DC/DC converter inputs.Ceramic capacitors are often chosen because of theirsmall size, low equivalent series resistance (ESR) and highRMS current capability. Also, recently, designers havebeen looking to ceramic capacitors due to shortages oftantalum capacitors.
上传时间： 2013-11-05
上传用户：comer1123
The LTM4600 DC/DC μModule regulator is a complete highpower density stepdown regulator for 10A continuous (14Apeak) loads. The device has two voltage options: 20VINmaximum for the LTM4600EV and 28VIN maximum for theLTM4600HVEV each housed in a small 15mm ¥ 15mm ¥2.8mm LGA surface mount package.
上传时间： 2013-10-10
上传用户：adada
The design of battery-powered equipment can often bequite challenging. Since few ICs can operate directly fromthe end-of-life voltage from a 2-cell battery (about 1.8V),most systems require a DC/DCconverter. The systemdesigner often has a limited area in which to place the DC/DC converter; associated inductors and capacitors must be
上传时间： 2013-11-23
上传用户：wys0120
TinyM0配套教程】 * 【TinyM0配套教程】接口技术与可靠性设计（I2C器件应用方案） * 【TinyM0配套教程】LPC1100系列Cortex-M0最小系统设计 * 【TinyM0配套教程】功能部件（SSP） * 【TinyM0配套教程】接口技术与可靠性设计（UART器件应用方案） * 【TinyM0配套教程】接口技术与可靠性设计（串行NOR Flash存储方案） * 【TinyM0配套教程】硬件体系结构（存储器寻址） * 【TinyM0配套教程】硬件体系结构（功率控制） * 【TinyM0配套教程】硬件体系结构（时钟系统） * 【TinyM0配套教程】功能部件（LPC1100系列器件简介、引脚连接模块、GPIO） * 【TinyM0配套教程】功能部件（定时器计数器） * 【TinyM0配套教程】接口技术与可靠性设计（DC/DC应用指南） * 【TinyM0配套教程】硬件体系结构（系统节拍定时器） * 【TinyM0配套教程】硬件体系结构（系统控制模块） * 【TinyM0配套教程】接口技术与可靠性设计（ESD器件应用指南） * 【TinyM0配套教程】功能部件（I2C） * 【TinyM0配套教程】功能部件（WDT） * 【TinyM0配套教程】功能部件（ADC） * 【TinyM0配套教程】功能部件（UART） * 【TinyM0配套教程】接口技术与可靠性设计（LDO应用指南） * 【TinyM0配套教程】接口技术与可靠性设计（复位设计）
上传时间： 2013-11-01
上传用户：litianchu
嵌入式CAN转UART模块 CSM100系列产品手册 CSM100系列UART转CAN 模块是集成微处理器、CAN-bus控制器、CAN-bus收发器、DC-DC转换、高速光电隔离于一体的嵌入式CAN转UART模块。
上传时间： 2014-01-03
上传用户：caixiaoxu26
本文着重介绍高效低纹波DC-DC降压稳压器SCY99090的特性、典型应用电路、电路中元器件的选型以及PCB的布局。
上传时间： 2014-12-27
上传用户：swaylong
The XL6003 regulator is fixed frequency PWM Boost (step-up) DC/DC converter, capable ofdriving 1050mA load current with excellent line and load regulation. The regulator is simple to use because it includes internal frequency compensation and a fixed-frequency oscillator so that it requires a minimum number of external components to work. The XL6003 could directly drive 5~10 3W LED units at VIN=12V.
上传时间： 2013-11-07
上传用户：xy@1314
文中设计了以DSP28335为控制核心的风光互补智能发电控制系统。分析了前级DC/DC斩波电路的工作原理并运用了基于改进扰动法的最大功率跟踪策略来实现风光互补系统最大功率的跟踪，采用DSP28335芯片作为控制核心，通过对直流斩波电路的检测与控制来实现对系统最大功率的跟踪和总体控制，并通过系统仿真与实验验证了设计的合理性。
上传时间： 2013-11-16
上传用户：顶得柱
