The above title is not happenstance and was arrived at afterconsiderable deliberation. As a linear IC manufacturer, it isour goal to encourage users to design and build switchingregulators. A problem is that while everyone agrees thatworking switching regulators are a good thing, everyonealso agrees that they are difficult to get working. Switchingregulators, with their high efficiency and small size, areincreasingly desirable as overall package sizes shrink.Unfortunately, switching regulators are also one of themost difficult linear circuits to design. Mysterious modes,sudden, seemingly inexplicable failures, peculiar regulationcharacteristics and just plain explosions are commonoccurrences. Diodes conduct the wrong way. Things gethot that shouldn’t. Capacitors act like resistors, fusesdon’t blow and transistors do. The output is at ground, andthe ground terminal shows volts of noise.
标签： Regulators Switching Poets for
上传时间： 2013-12-19
上传用户：奇奇奔奔
The LTM8020, LTM8021, LTM8022 and LTM8023 μModule®regulators are complete easy-to-use encapsulated stepdownDC/DC regulators intended to take the pain and aggravationout of implementing a switching power supplyonto a system board. With a μModule regulator, you onlyneed an input cap, output cap and one or two resistorsto complete the design. As one might imagine, this highlevel of integration greatly simplifi es the task of printedcircuit board design, reducing the effort to four categories:component footprint generation, component placement,routing the nets, and thermal vias.
上传时间： 2014-01-18
上传用户：laomv123
In August of 1992 LTC published Application Note 49, “Illumination Circuitry for Liquid Crystal Displays.” One notable aspect of this event is that it generated more response than all previous LTC application notes combined. This level of interest, along with significant performance advances since AN-49’s appearance, justifies further discussion of LCD backlighting circuitry.
上传时间： 2013-11-19
上传用户：lanjisu111
For a variety of reasons, it is desirable to charge batteriesas rapidly as possible. At the same time, overchargingmust be limited to prolong battery life. Such limitation ofovercharging depends on factors such as the choice ofcharge termination technique and the use of multi-rate/multi-stage charging schemes. The majority of batterycharger ICs available today lock the user into one fixedcharging regimen, with at best a limited number ofcustomization options to suit a variety of application needsor battery types. The LTC®1325 addresses these shortcomingsby providing the user with all the functionalblocks needed to implement a simple but highly flexiblebattery charger (see Figure 1) which not only addressesthe issue of charging batteries but also those of batteryconditioning and capacity monitoring.
上传时间： 2013-10-19
上传用户：royzhangsz
为了改变目前电网现场作业管理的变电巡检、变电检修试验、输电线路巡检检修等管理系统各自独立运行，信息不能共享，功能、效率受限，建设和维护成本高的现状，提出了采用B/S+C/S构架模式，将各现场作业管理模块和生产MIS（管理系统）集成为一体的现场作业管理系统的设计方案，做到各子系统和生产MIS软硬资源共享，做到同一数据唯一入口、一处录入多处使用。各子系统设备人员等基础信息来源于生产管理系统，各子系统又是生产管理系统的作业数据、缺陷信息的重要来源。经过研究试用成功和推广应用，目前该系统已在江西电网220 kV及以上变电站全面应用。 Abstract: In order to improve the status that the substation field inspection system， substation equipments maintenance and testing system， power-line inspection and maintenance system are running independent with each other. They can?蒺t share the resource information which accordingly constrains their functions and efficiency， and their construction and maintenance costs are high. This paper introduces a field standardized work management system based on B/S+C/S mode， integrating all field work management systems based on MIS and share the equipments and employee?蒺s data of MIS，the field work data of the sub systems are the source information of MIS， by which the same single data resouce with one-time input can be utilized in multiple places. After the research and testing， this system is triumphantly using in all 220kV and above substations in Jiangxi grid.
上传时间： 2013-11-15
上传用户：han_zh
锁定放大是微弱信号检测的重要手段。基于相关检测理论，利用开关电容的开关实现锁定放大器中乘法器的功能，提出开关电容和积分器相结合以实现相关检测的方法，并设计出一种锁定放大器。该锁定放大器将微弱信号转化为与之相关的方波，通过后续电路得到正比于被测信号的直流电平，为后续采集处理提供方便。测量数据表明锁定放大器前级可将10-6 A的电流转换为10-1 V的电压，后级通过带通滤波器级联可将信号放大1×105倍。该方法在降低噪声的同时，可对微弱信号进行放大，线性度较高、稳定性较好。 Abstract: Lock-in Amplifying（LIA）is one of important means for weak signal detection. Based on cross-correlation detection theory， switch in the swithched capacitor was used as multiplier of LIA， and a new method of correlation detection was proposed combining swithched capacitor with integrator. A kind of LIA was designed which can convert the weak signal to square-wave， then DC proportional to measured signal was obtained through follow-up conditioning circuit， providing convenience for signal acquisition and processing. The measured data shows that the electric current（10-6 A） can be changed into voltage（10-1 V） by LIA， and the signal is magnified 1×105 times by cascade band-pass filter. The noise is suppressed and the weak signal is amplified. It has the advantages of good linearity and stability.
上传时间： 2013-11-29
上传用户：黑漆漆
CP-1000 是 Antec 新的高阶电源供应器.结合全新的技术,CP-1000 提供了绝佳的性价比. 新的功能有: 革新的电路设计; 较大的空间可以安排电子零件及增进风流; 直流式的风道设计,让风扇的风可以直接吹进机身内部. 使用较大的风扇在低转速时就可以提供很好的风流效果,而且还不会制造噪音. Antec 新的 form factor: CPX, 他比其他标准大小也使用大风扇的 PSU 可以提供更好的风流效果. CP-1000 可以安装在 Antec 的Performance One 和 Gaming 机箱上,包含 Twelve Hundred, P183 和 P193.
上传时间： 2013-10-17
上传用户：lijianyu172
欧姆龙plc编程软件CX-Programmer使用手册 第一章安装和启动 1. 安装 1-1. 安装CX-Programmer 1-2. 在线注册 2. 打开新工程和设置设备型号 3. 打开新工程和设置设备型号 4. 主窗口 4-1.兼容SYSWIN软件的按键分配 4-2. 段 4-3.删除和显示其他窗口 5.创建程序 5-1.常开接点的输入 5-2.线圈的输入 5-3.符号注释的编辑 5-4.条注释的输入 5-5.常闭接点的输入 5-6.元素注释的输入 5-7.上升沿微分接点的输入 5-8.下降沿微分接点的输入 5-9.向上垂线的输入 5-10.向下垂线的输入 5-11.高级指令的输入1 - 字符串的输入 5-12.高级指令的输入1 - 有用的功能 5-13.辅助继电器的输入- 1.0 秒时钟脉冲位 5-14.高级指令的输入2 – 微分指令的输入 5-15.或逻辑的条输入 5-16.高级指令的输入3 – 通过功能号来输入 5-17.定时器指令的输入 5-18.计数器指令的输入 5-19.条的编辑…复制和粘贴 5-20. END指令的输入 第二章在线/调试 1. 程序错误检查(编译) 2. 进入在线 3. 监视 4. 监视- 2 同时监视程序中多处位置 5. 监视- 3 以十六进制数监视 6. 监视- 4 查看窗口 7. 监视- 5 查看窗口的当前值修改和二进制数监视 8. 查看窗口的有用功能 9. 监视- 6 监视窗口- 2 10.监视- 7 以短条形式显示 11.监视- 8 微分监视 12.强制为On/Off 13.强制-on/off 位的显示列表 14.修改定时器的设定值 15.修改定时器的当前值 16.查找功能- 1 通过地址引用工具查找 17.查找功能- 2 梯形图的折回查找 18.查找功能- 3 通过注释的关键字来查找 19.查找功能- 4 进入条注释 20.查找功能- 5 查找位地址 21.在线编辑 实用的功能 相关资料： 欧姆龙PLC编程软件CX-Programmer7.1 简体中文版
上传时间： 2013-10-25
上传用户：84425894
Microchip 单片机的速度和复杂性已经到达足以要 求降低电源电压的程度，并正在向 5V 电源电压以 下转换。但问题是绝大多数接口电路仍然是为 5V 电源而设计的。这就意味着，作为设计人员，我们 现在面临着连接 3.3V 和 5V 系统的任务。此外， 这个任务不仅包括逻辑电平转换，同时还包括为 3.3V 系统供电、转换模拟信号使之跨越 3.3V/5V 的 障碍。 技巧和诀窍 DS41285A_CN 第 2 页 . 2006 Microchip Technology Inc. 本 《技巧和诀窍》提供了一些电源供电组件、数 字电平转换组件甚至模拟转换组件，以解决所面临 的挑战。全书对每种转换均给出了多种选择方案， 从单片 （All-in-One）接口器件到低成本的分立解 决方案都有涉及。简而言之，无论导致转换的原因 是复杂性、成本还是尺寸，设计人员处理 3.3V 挑 战可能需要的全部组件均在本文有所讨论。
上传时间： 2013-10-30
上传用户：wqxstar
针对煤矿井下调度及紧急救援系统的需求，以DTMF编解码模块为核心，设计了具有自动拨号功能的新型电话系统。该系统利用MT8880对DTMF信号的编解码功能实现一键拨号和远程设置，通过检测振铃和忙音信号，完成自动摘机和挂机过程，配合AGC等外围电路达到话音清晰流畅的效果。 Abstract: To meet the demand for mine scheduling and emergency rescue system， with using DTMF signal codec as the core， a new telephone system was designed with automatic dialing function. In the system， the DTMF signal encoding and decoding function of MT8880 was used to achieve one-touch dialing and remote setting. The circuit detects the ringing and busy signal， and then completes automatic off-hook and hangup. With AGC(Automatic Gain Control) and other peripheral circuits， the voice was regulated to a clear and smooth effect.
上传时间： 2014-11-18
上传用户：ly1994
