微电脑型RS-485显示电表（24*48mm/48*96mm） 特点： 5位数RS-485显示电表 显示范围-19999-99999位數 通訊协议Modbus RTU模式 宽范围交直流兩用電源設計 尺寸小,穩定性高 主要规格： 显示范围:-19999~99999 digit RS-485传输速度: 19200/9600/4800/2400 selective RS-485通讯位址: "01"-"FF" RS-485通讯协议: Modbus RTU mode 显示幕: Red high efficiency LEDs high 10.16 mm (0.4") (MMX-RS-11X) Red high efficiency LEDs high 20.32 mm (0.8") (MMX-RS-12X) Red high efficiency LEDs high 10.16 mm (0.4")x2 (MMX-RS-22X) 参数设定方式: Touch switches 记忆方式: Non-volatile E²PROM memory 绝缘耐压能力: 2KVac/1 min. (input/power) 使用环境条件: 0-50℃(20 to 90% RH non-condensed) 存放环境条件: 0-70℃(20 to 90% RH non-condensed) CE认证: EN 55022:1998/A1:2000 Class A EN 61000-3-2:2000 EN 61000-3-3:1995/A1:2001 EN 55024:1998/A1:2001
上传时间： 2015-01-03
上传用户：feitian920
微电脑型单相交流集合式电表（单相二线系统） 特点： 精确度0.25%满刻度±1位数 可同时量测与显示交流电压,電流,頻率,瓦特,(功率因數/視在功率) 交流電壓,電流,瓦特皆為真正有效值(TRMS) 交流電流,瓦特之小數點可任意設定 瓦特單位W或KW可任意設定 CT比可任意設定(1至999) 輸入與輸出絕緣耐压 2仟伏特/1分鐘( 突波測試強度4仟伏特(1.2x50us) 數位RS-485界面 (Optional) 主要规格： 精确度: 0.1% F.S.±1 digit (Frequency) 0.25% F.S.±1 digit(ACA,ACV,Watt,VA) 0.25% F.S. ±0.25o(Power Factor) (-.300~+.300) 输入负载: <0.2VA (Voltage) <0.2VA (Current) 最大过载能力: Current related input: 3 x rated continuous 10 x rated 30 sec. 25 x rated 3sec. 50 x rated 1sec. Voltage related input: maximum 2 x rated continuous 过载显示: "doFL" 显示值范围: 0~600.0V(Voltage) 0~999.9Hz(Frequency)(<20% for voltage input) 0~19999 digit adjustable(Current,Watt,VA) 取样时间: 2 cycles/sec. RS-485通讯位址: "01"-"FF" RS-485传输速度: 19200/9600/4800/2400 selective RS-485通信协议: Modbus RTU mode 温度系数: 100ppm/℃ (0-50℃) 显示幕: Red high efficiency LEDs high 10.16 mm(0.4") 参数设定方式: Touch switches 记忆型式: Non-volatile E²PROM memory 绝缘抗阻: >100Mohm with 500V DC 绝缘耐压能力: 2KVac/1 min. (input/output/power) 1600 Vdc (input/output) 突波测试: ANSI c37.90a/1974,DIN-IEC 255-4 impulse voltage 4KV(1.2x50us) 使用环境条件: 0-50℃(20 to 90% RH non-condensed) 存放环境条件: 0-70℃(20 to 90% RH non-condensed) CE认证: EN 55022:1998/A1:2000 Class A EN 61000-3-2:2000 EN 61000-3-3:1995/A1:2001 EN 55024:1998/A1:2001
上传时间： 2015-01-03
上传用户：几何公差
特点： 精确度0.25%满刻度±1位數 可量测交流瓦特/乏爾/功率因數/相角 显示范围0- ±19999可任意规划 输入与输出绝缘耐压2仟伏特/1分钟(input/output/power)) 突波测试强度4仟伏特(1.2x50us) 2组警报功能 (Optional) 15BIT类比输出功能 (Optional) 数位RS-485界面 (Optional)
上传时间： 2013-11-08
上传用户：330402686
Abstract: Many modern industrial, medical, and commercial applications require temperature measurements in the extended temperature rangewith accuracies of ±0.3°C or better, performed with reasonable cost and often with low power consumption. This article explains how platinumresistance temperature detectors (PRTDs) can perform measurements over wide temperature ranges of -200°C to +850°C, with absolute accuracyand repeatability better than ±0.3°C, when used with modern processors capable of resolving nonlinear mathematical equation quickly and costeffectively. This article is the second installment of a series on PRTDs. For the first installment, please read application note 4875, "High-Accuracy Temperature Measurements Call for Platinum Resistance Temperature Detectors (PRTDs) and Precision Delta-Sigma ADCs."
上传时间： 2013-11-06
上传用户：WMC_geophy
Modern electronic systems solve so many difficult problems that they often seem like magic. Nonetheless, these systems all have thesame basic limitation: they need a source of electrical power! Most of the time this is a straightforward challenge for the electronicdesigner, because there are many power-delivery solutions. Yet sometimes a device has no direct power source, and running wiresor replacing batteries is impractical. Even when long-life batteries are usable, they eventually need to be replaced, which requires aservice call.
标签： 能量收集
上传时间： 2015-01-03
上传用户：zukfu
因为测量系统都用50欧姆, 如非特指, 以下所说的Gain均指功率增益(Power Gain). 但是一般的接收机的输入输出并非50欧姆, 因此有必要考虑电压增益(Voltage Gain).
上传时间： 2015-01-03
上传用户：1318695663
Have you had the exasperating experience of a laptop orPDA defi antly not responding to your commands? Youfrantically press key after key, but to no avail. As hopeturns to anger (but just before you throw the company’slaptop through the window) you slam your fi nger againstthe on/off power button. Ten seconds later, your laptopfi nally surrenders and the screen goes black in a highpitched whimper.
上传时间： 2013-12-10
上传用户：Vici
ACPR (adjacent channel power ratio), AltCPR (alternatechannel power ratio), and noise are important performancemetrics for digital communication systems thatuse, for example, WCDMA (wideband code division multipleaccess) modulation. ACPR and AltCPR are bothmeasures of spectral regrowth. The power in the WCDMAcarrier is measured using a 5MHz measurement bandwidth;see Figure 1. In the case of ACPR, the total powerin a 3.84MHz bandwidth centered at 5MHz (the carrierspacing) away from the center of the outermost carrier ismeasured and compared to the carrier power. The resultis expressed in dBc. For AltCPR, the procedure is thesame, except we center the measurement 10MHz awayfrom the center of the outermost carrier.
上传时间： 2013-11-02
上传用户：maricle
Frequently, voltage reference stability and noise defi nemeasurement limits in instrumentation systems. In particular,reference noise often sets stable resolution limits.Reference voltages have decreased with the continuingdrop in system power supply voltages, making referencenoise increasingly important. The compressed signalprocessing range mandates a commensurate reductionin reference noise to maintain resolution. Noise ultimatelytranslates into quantization uncertainty in A to D converters,introducing jitter in applications such as scales, inertialnavigation systems, infrared thermography, DVMs andmedical imaging apparatus. A new low voltage reference,the LTC6655, has only 0.3ppm (775nV) noise at 2.5VOUT.Figure 1 lists salient specifi cations in tabular form. Accuracyand temperature coeffi cient are characteristic ofhigh grade, low voltage references. 0.1Hz to 10Hz noise,particularly noteworthy, is unequalled by any low voltageelectronic reference.
上传时间： 2013-10-30
上传用户：wxhwjf
在Multisim 10软件环境下，设计一种由运算放大器构成的精确可控矩形波信号发生器，结合系统电路原理图重点阐述了各参数指标的实现与测试方法。通过改变RC电路的电容充、放电路径和时间常数实现了占空比和频率的调节，通过多路开关投入不同数值的电容实现了频段的调节，通过电压取样和同相放大电路实现了输出电压幅值的调节并提高了电路的带负载能力，可作为频率和幅值可调的方波信号发生器。Multisim 10仿真分析及应用电路测试结果表明，电路性能指标达到了设计要求。 Abstract: Based on Multisim 10， this paper designed a kind of rectangular-wave signal generator which could be controlled exactly composed of operational amplifier， the key point was how to implement and test the parameter indicators based on the circuit diagram. The duty and the frequency were adjusted by changing the time constant and the way of charging and discharging of the capacitor， the width of frequency was adjusted by using different capacitors provided with multiple switch， the amplitude of output voltage was adjusted by sampling voltage and using in-phase amplifier circuit，the ability of driving loads was raised， the circuit can be used as squarewave signal generator whose frequency and amplitude can be adjusted. The final simulation results of Multisim 10 and the tests of applicable circuit show that the performance indicators of the circuit meets the design requirements.
上传时间： 2014-01-21
上传用户：shen007yue
