Enter the Matrix MS-DOS screensaver. Sample of using bios functions (by int 10h) for text data output (monitor in the text mode) and keyboard input. Requires: Borland C++ 3.1 for DOS.
标签： screensaver functions Matrix MS-DOS
上传时间： 2013-11-29
上传用户：hopy
This document gives the code for programming a CC2500 transceiver using Altera Stratix FPGA. The FPGA and CC2500 are connected through SPI mode with the FPGA as the master and CC2500 as the slave.
标签： programming transceiver document Stratix
上传时间： 2014-01-15
上传用户：wuyuying
This program requires the DSP2833x header files. // // This program requires an external I2C RTC connected to // the I2C bus at address 0x6f. // // As supplied, this project is configured for "boot to SARAM" // operation. The 2833x Boot Mode table is shown below. // For information on configuring the boot mode of an eZdsp, // please refer to the documentation included with the eZdsp,
标签： requires program This external
上传时间： 2017-07-12
上传用户：dianxin61
This program requires the DSP2833x header files. // // As supplied, this project is configured for "boot to SARAM" // operation. The 2833x Boot Mode table is shown below. // For information on configuring the boot mode of an eZdsp, // please refer to the documentation included with the eZdsp,
标签： configured requires supplied program
上传时间： 2014-01-10
上传用户：lixinxiang
This software is developed to provide ease with controller design. For PID control, options are given to design and analyse the compensated and uncompensated system. You are free to choice among Proportional PI, PD and PID mode of control. Both frequency and time domain characteristics can be observed. Special Menus are given to observe time and frequency response plots. For Statefeedback controller similar options are given. But this is limited to second order system only.
标签： controller developed software control
上传时间： 2017-07-25
上传用户：aysyzxzm
RS_latch using vhdl, When using static gates as building blocks, the most fundamental latch is the simple SR latch, where S and R stand for set and reset. It can be constructed from a pair of cross-coupled NOR (Not OR) logic gates. The stored bit is present on the output marked Q. Normally, in storage mode, the S and R inputs are both low, and feedback maintains the Q and Q outputs in a constant state, with Q the complement of Q. If S (Set) is pulsed high while R is held low, then the Q output is forced high, and stays high when S returns to low similarly, if R (Reset) is pulsed high while S is held low, then the Q output is forced low, and stays low when R returns to low.
标签： using fundamental the RS_latch
上传时间： 2017-07-30
上传用户：努力努力再努力
hese are the zip files that are associated with application note ADSP-BF533 Blackfin Booting Process (EE-240) example.zip: Used throughout the EE-note to explain in detail the various booting modes. BF533 Ez Kit Multiple DXE Boot.zip: Multi-DXE Boot Example used with the ADSP-BF533 Ez-Kit Lite. Host Boot.zip: Example Host code to demonstrate SPI Slave Mode Booting Program_Atmel.zip: Example code that programs the Atmel DataFlashes via an ADSP-BF532 Processor All programs have been written for VisualDSP++ 3.5
标签： application associated are Blackfin
上传时间： 2017-07-30
上传用户：tonyshao
Complete coverage of all four CCNP exams: ? EIGRP, OSPF, IS-IS, and BGP ? Optimizing routing ? IP multicast ? IPv6 ? VLAN implementation ? Spanning Tree ? InterVLAN routing ? Layer 3 redundancy ? Wireless LANs ? VoIP in campus networks ? Campus network security ? Frame-mode MPLS ? IPsec ? Cisco device hardening ? Cisco IOS? threat defenses ? Cisco VoIP ? QoS and AutoQoS ? Wireless scalability
标签： Optimizing Complete coverage routing
上传时间： 2017-09-26
上传用户：cuibaigao
The TJA1040 is an advanced high speed CAN transceiver for use in automotive and general industrial applications. It supports the differential bus signal representation described in the international standard for in-vehicle high speed CAN applications (ISO11898). CAN (Controller Area Network) is the standard protocol for serial in-vehicle bus communication, particularly for Engine Management and Body Multiplexing. The TJA1040 provides a Standby mode, as known from its functional predecessors PCA82C250 and PCA82C251, but with significantly reduced power consumption. Besides the excellent low-power behavior the TJA1040 offers several valuable system improvements. Highlights are the absolute passive bus behavior if the device is unpowered as well as the excellent EMC performance.
标签： CAN
上传时间： 2015-03-23
上传用户：Yuan Lo
制作驱动程序的好工具.支持 ISA,EISA,PCI,Plug&Play 和 DMA.不需要牵涉到很低层的东西即可在很短的时间里编出驱动程序.内含教程.使用WinDriver的优点是:开发者并不需要熟悉任何内部操作系统或kernel programming或DDK及任何驱动程式.WinDriver同时允许开发者能在自己所熟悉的开发环境下,利用使用者模式(User Mode)如使用MSDEV Visual C/C++,Borland C++Builder,Delphi或任何Win32编译器.使用WinDriver所开发的驱动程式均可用于Windows 9x,NT/2000,NT Embedded,CE Linux and Solaris等平台.
上传时间： 2015-06-02
上传用户：1663066023
