智能仪表人机界面软件自动生成的方法 The Method of Automatic Generation for HMI Software in Intelligent Inst
上传时间： 2013-07-04
上传用户：woshini123456
The purpose of this note is to present how to use the ST7 PWM/BRM for the generation of a50Hz si
上传时间： 2013-06-01
上传用户：huyanju
Integrating A/D converters have two characteristics incommon. First, as the name implies, their
上传时间： 2013-04-24
上传用户：matlab
·原书名： WCDMA FOR UMTS-Radio Access for Third Generation Mobile Communication 作者：（芬）哈里.霍尔马 安提.托斯卡拉 [同作者作品] 译者： 周胜[同译者作品] 等 丛书名： 其他 出版社：机械工业出版社* ISBN：7111096681 上架时间：2002-1-19 出版日期：2002 年1月 页码：266 版次：1-1
上传时间： 2013-08-06
上传用户：y307115118
·SystemVerilog is a rich set of extensions to the IEEE 1364-2001 Verilog Hardware Description Language (Verilog HDL). These extensions address two major aspects of HDL-based design. First, modeling ver
标签： nbsp SystemVerilog Design for
上传时间： 2013-07-14
上传用户：ainimao
Abstract: This application note describes a new generation of digital-input Class D audio amplifiers that achieve high PSRRperformance, comparable to traditional analog Class D amplifiers. More importantly, these digital-input Class D amplifiersprovide additional benefits of reduced power, complexity, noise, and system cost.
上传时间： 2013-12-20
上传用户：JIUSHICHEN
Abstract: For many first-time users, finding the right logger that meets their needs can be a challenging task. In simple
上传时间： 2014-01-19
上传用户：缥缈
The LM20, LM45, LM50, LM60, LM61, and LM62 are analog output temperature sensors. They have various output voltage slopes (6.25mV/°C to 17mV/°C) and power supply voltage ranges (2.4V to 10V).The LM20 is the smallest, lowest power consumption analog output temperature sensor National Semiconductor has released. The LM70 and LM74 are MICROWIRE/SPI compatible digital temperature sensors. The LM70 has a resolution of 0.125°C while the LM74 has a resolution of 0.625°C. The LM74 is the most accurate of the two with an accuracy better than ±1.25°C. The LM75 is National’s first digital output temperature sensor, released several years ago.
上传时间： 2014-12-23
上传用户：yl8908
ANALOG INPUT BANDWIDTH is a measure of the frequencyat which the reconstructed output fundamental drops3 dB below its low frequency value for a full scale input. Thetest is performed with fIN equal to 100 kHz plus integer multiplesof fCLK. The input frequency at which the output is −3dB relative to the low frequency input signal is the full powerbandwidth.APERTURE JITTER is the variation in aperture delay fromsample to sample. Aperture jitter shows up as input noise.APERTURE DELAY See Sampling Delay.BOTTOM OFFSET is the difference between the input voltagethat just causes the output code to transition to the firstcode and the negative reference voltage. Bottom Offset isdefined as EOB = VZT–VRB, where VZT is the first code transitioninput voltage and VRB is the lower reference voltage.Note that this is different from the normal Zero Scale Error.CONVERSION LATENCY See PIPELINE DELAY.CONVERSION TIME is the time required for a completemeasurement by an analog-to-digital converter. Since theConversion Time does not include acquisition time, multiplexerset up time, or other elements of a complete conversioncycle, the conversion time may be less than theThroughput Time.DC COMMON-MODE ERROR is a specification which appliesto ADCs with differential inputs. It is the change in theoutput code that occurs when the analog voltages on the twoinputs are changed by an equal amount. It is usually expressed in LSBs.
上传时间： 2013-11-12
上传用户：pans0ul
Power conversion by virtue of its basic role produces harmonics due to theslicing of either voltages or currents. To a large extent the pollution in theutility supply and the deterioration of the power quality has been generatedor created by non-linear converters. It is therefore ironic that power convertersshould now be used to clean up the pollution that they helped to create inthe first place.In a utility system, it is desirable to prevent harmonic currents (which resultin EMI and resonance problems) and limit reactive power flows (whichresult in transmission losses).Traditionally, shunt passive filters, comprised of tuned LC elements andcapacitor banks, were used to filter the harmonics and to compensate forreactive current due to non-linear loads. However, in practical applicationsthese methods have many disadvantages.
上传时间： 2013-11-05
上传用户：AISINI005
