LED 线阵显示装置, 分为 LED 线性旋转显示主机和图文录入器两部分。主机用直流电机带动由红绿 LED 组成的线阵旋转, 同时线阵按照时序依次切换显示状态, 在固定区域利用视觉暂留效果形成 16×16 点阵, 用以显示图文;图文录入器用 HMI 触控屏作为人机交互界面, 实现图文录入和回放功能。主机与图文录入器通过无线通信方式进行信息交互,可由图文录入器控制主机切换不同工作任务, 以及改变线阵显示内容。The LED linear array display device is divided into two parts:the one is the main unit used to display content,and the other one is used to input the contents.The main unit is driven by a DC motor to rotate the linear array composed by red and green light emitting diodes.At the same time,the 16×16 dot matrix that switching the display state according to the time sequence on the main unit displays pictures and texts in the fixed area,by using the visual temporary effect.The HMI touch screen is used as human machine interface to realize the function that input and playback pictures and texts.The two parts of the device communicate with each other through wireless communication.The image and text input controller can control the main unit to switch different tasks and change the content of linear array displayed.
标签： stc12c5a60s2 单片机 led
上传时间： 2022-03-28
上传用户：jiabin
文章提出了一种基于AT89S51单片机的智能家居系统的设计,该系统具有室内煤气以及烟雾的检测、家庭室内防盗等功能。文章详细分析了系统的总体设计,详尽分析并设计了煤气传感器模块、烟雾传感器模块、人体红外感应传感器模块、报警模块等各硬件部分,并利用PROTUES软件进行了系统仿真。仿真结果证明:系统具有成本低、效率高、操作方便等优点,达到了预期设计的效果。This paper presents the design of an intelligent home system based on AT89S51 microcontroller.The system has the functions of detecting indoor gas and smoke,guarding against theft in the home,and so on.The overall design of the system is analyzed in detail.The gas sensor module,smoke sensor module,human infrared sensor module,alarm module and other hardware parts are analyzed and designed in detail,and the system simulation is carried out using PROTUES software.The simulation results show that the system has the advantages of low cost,high efficiency,convenient operation and so on,and achieves the expected design effect.
上传时间： 2022-03-28
上传用户：
设计功率MOSFET驱动电路时需重点考虑寄生参数对电路的影响。米勒电容作为MOSFET器件的一项重要参数,在驱动电路的设计时需要重点关注。重点观察了MOSFET的开通和关断过程中栅极电压、漏源极电压和漏源极电流的变化过程,并分析了米勒电容、寄生电感等寄生参数对漏源极电压和漏源极电流的影响。分析了栅极电压在米勒平台附近产生振荡的原因,并提出了抑制措施,对功率MOSFET的驱动设计具有一定的指导意义。When designing the drive circuit of power MOSFET,the influence of parasitic parameters on the circuit should be concerned.As an important parameter of MOSFET device,Miller capacitance should be considered in the design of drive circuit.The variation of gate voltage,drain source voltage and drain source current during the turn-on and turn-off of MOSFET were observed.The influences of parasitic parameters such as Miller capacitance and parasitic inductance on drain source voltage and drain source current were analyzed.The reasons of gate voltage oscillation nearby Miller plateau were analyzed,and the restraining measures were put forward.This research was instructive for the drive design of power MOSFET.
标签： mosfet
上传时间： 2022-04-02
上传用户：默默
通过采用无桥PFC和半桥LLC谐振变换器作为数字开关电源的主变换拓扑,基于STM32系列微控制器的全数字控制PFC和DC-DC变换器,首先对数字化开关电源方案进行对比,然后阐述了200W数字开关电源整体方案,并对数字开关电源的无桥PFC和半桥LLC变换器进行系统研究。By using a bridgeless PFC and a half-bridge LLC resonant converter as the main conversion topology of the digital switching power supply,the all-digital control PFC and DC-DC converter based on the STM32 series of microcontrollers,firstly the digital switching power supply scheme is compared,and then the overall scheme of 200 W digital switching power supply is expounded, and the bridgeless PFC and half-bridge LLC converter of digital switching power supply are systematically studied.
标签： 数字开关电源
上传时间： 2022-04-02
上传用户：qingfengchizhu
电学中的测量技术涉及范围非常广,电流测量在电学计量中占有非常重要的位置。如何精确地进行电流测量是精密测量的一大难题。传统的电流检测电路多采用运算放大芯片与片外电流检测电路相结合的方式,电路集成度很低,需要较多的接口和资源才能完成对电路的检测。本文把所有电路部分都集成在一块芯片上,包括检测电阻,运算放大器电路及模拟转数字转换电路,从而在电路内部可以进行电流检测,使电路更好的集成化。前置电路使用二级共源共栅结构的运算放大器,减小沟道长度调制效应造成的电流误差。10位SAR ADC中采用电容驱动能力强的传输门保证了模数转化器的有效精度。比较器模块采用再生锁存器与迟滞比较器作为基础单元组合解决精密测量的问题。本设计可以作为嵌入芯片内的一小部分而检测芯片中的微小电流1mA~100mA,工作电压在1.8v左右,电流检测精度预期达到10uA的需求。The measurement technology in electricity involves a wide range,and current measurement plays a very important position in electrical measurement.How to accurately measure current is a big problem in precision measurement. The traditional current detecting circuit adopts the combination of the operational amplifier chip and theoff-chip current detecting circuit, The circuit integration is very low, and more interfaces and resources are needed tocomplete the circuit detection.This topic integrates all the circuit parts into one chip, including detection resistance, operational amplifier circuit andanalog to digital conversion circuit. Highly integrated circuit makes the external resources on the chip more intensive,so that current detection can be carried out inside the circuit, so that the circuit can be better integrated. Thefront-end circuit of this project uses two-stage cascade operational amplifier and cascade tube to reduce the currenterror caused by channel length modulation effect. In 10-bit SAR ADC, the transmission gate with strong capacitivedriving ability ensures the effective accuracy of the analog-to-digital converter. Comparator module uses regenerativelatch and hysteresis comparator as basic unit to solve the difficult problem of precision measurement. This topic can beused as a small part of the embedded chip to detect the micro-current in the chip 1 mA~100 mA, the working voltageis about 1.8v, and the current detection accuracy is expected to reach the requirement of 10 uA.
上传时间： 2022-04-03
上传用户：
为设计高效率、低损耗的PFC电路,本文基于UCC28019进行电路设计。以UCC28019输出的PWM波形来控制Boost升压斩波为核心电路,使电路中的电容交替地充放电、电感交替的储存和释放能量,最后实现在输入AC20V~24V电压情况下稳定输出DC38V。测试结果表明,系统实现效率为95%左右,电压调整率小于1%,电源功率因数0.99。交流输入电压为19.0-25.8 V时,输出直流电压稳定性较好,电感无明显啸叫且纹波小,具有一定的带负载能力和实用性。In order to design the PFC circuit with high efficiency and low loss,this paper designs the circuit based on UCC28019.The PWM waveform output by UCC28019 is used to control boost chopper as the core circuit,which alternately charges and discharges capacitors,stores and releases energy by inductors,and finally achieves stable output of DC38 V under the input voltage of AC20 V~24 V.The test results show that the system achieves about 95% efficiency,the voltage adjustment rate is less than 1%,the power factor is 0.99,and the AC input voltage is 19.0-25.8 V.The output DC voltage stability is good,the inductance has no obvious whistle and the ripple is small,so it has certain load capacity and practicability.
上传时间： 2022-04-03
上传用户：
目的:自主研制一款超声手术刀电源控制系统,以减少能量的消耗,维持手术刀的正常温度。方法:对超声换能器在谐振附近的等效电路建立模型,并设计基于数字信号处理(DSP)的超声手术刀的硬件控制系统。结果:经对电源控制系统的电路和工作性能测试,生成的电流和电压的有效值等参数,能够及时调整电源的频率,并达到预期的功能指标,使超声手术刀工作在谐振状态。结论:以DSP为核心设计的超声手术刀电源控制系统,测试指标均能够达到预期的要求,能够使系统在谐振状态下工作。Objective: To independently develop a power control system of ultrasonic scalpel so as to reduce the energy consumption and maintain the normal temperature of ultrasonic scalpel. Methods: In this paper, the model of equivalent circuit of ultrasonic transducer nearby syntony was built up, and the hardware control system of ultrasonic scalpel based on digital signal processing(DSP) was designed. Results: Through testing the circuit and work performance of power control system, the series of parameters such as effective value and so on which were produced by this system could adjust frequency of power source in time and attain anticipative functional indicator, and it took the ultrasonic scalpel to work in syntonic situation. Conclusion: The tested indicators of power control system of ultrasonic scalpel based on the kernel design of DSP can attain anticipative requirement, and can take this system to work in syntonic situation.
上传时间： 2022-04-03
上传用户：bluedrops
本文设计了一种磁致伸缩位移传感器,介绍了该磁致伸缩位移传感器的测量原理,通过结构优化设计提高了仪器的性能,详述了硬件电路设计及实现方法,完成了软件设计,实现了高压充电、问询脉冲加载、时间测量及滤波等功能,并通过实验对其性能进行了验证。所研制的磁致伸缩位移传感器具有测量精度高、长期稳定性好等特点,满足了大量程、高精度、恶劣环境等测量的要求。A kind of sensor based on magnetostrictive principle is designed.The measuring principle of the magnetostrictive displacement sensor is introduced,the performance of the instrument is improved by the structural optimization design,and introduced the hardware circuit design and the realization method,completed the software design,realized the functions of the high voltage charging,inquiries pulse loading,time measurement and filtering,and its performance is verified through the experiment.The magnetostrictive displacement sensor has the characteristics of high measuring precision.The sensor meets the requirements of large range,high precision,poor environment and so on.
标签： 位移传感器
上传时间： 2022-04-06
上传用户：
随着科技的发展，人们在日常生活中使用的电器越来越多，电子设备的电磁兼容性（EMC）也越来越重要。所以，人们对电子设备的电磁兼容性的要求也越来越严格，越来越规范。而在市场竞争中，如何降低成本、减少设备体积，是各电子设备制造厂家重点研究的课题。通过对开关电源的EMI滤波电路的类别和相应的技术特点进行分析，设计出一种既能提高性能，又能降低成本的滤波电路。With the development of technology, appliances people use in their daily lives, more and more electronic devices electromagnetic compatibility （ EMC ） has become increasingly important. So, people electromagnetic compatibility requirements of electronic devices have become increasingly stringent, more and more standardized. The competition in the market, how to reduce costs, reduce equipment size, is the subject of the electronic equipment manufacturer focused on research. Through the technical characteristics of the respective category and the EMI filter circuit switching power supply is analyzed both designed to improve a performance of the filter circuit can reduce the cost.
上传时间： 2022-04-23
上传用户：
超声波换能器作为一种实用的检测手段，能实现声波所携带的信息和电能之间转换。它的性能优良，价格低廉，操作方便，易于调试，因此在工农业生产中发挥着重要的作用。但目前换能器驱动电路的发射频率多为40 kHz，本文针对1 MHz的超声波换能器电路进行了设计，主要介绍了它的发射驱动电路和接收驱动电路的设计方案，并对它们的功能进行了详细地说明。最后搭建实验平台，并对电路的输入、输出模块进行了测试。实验结果表明，换能器电路运行良好，可以为超声波高精度测量领域的应用提供参考。As a practical means of detection, ultrasonic transducer can realize the conversion between theinformation carried by sound wave and electric energy.It has the advantages of excellent performance,low cost, convenient operation and debugging, so plays an important role in industrial and agriculturalproduction.However, the transmitting frequency of the driving circuit for most transducer is 40 kHz.Thecircuit of 1 MHz ultrasonic transducer is designed In this paper. It mainly introduces the emissive drivingcircuit and the receiving circuit design and the detailed function of them. Finally, the experimentalplatform is built, and the circuit of input and output were tested. Experiments show that the transducer＇ s...
上传时间： 2022-04-28
上传用户：
