Avalanche photodiodes (APDs) are widely utilized in laserbased fiberoptic systems to convert optical data intoelectrical form. The APD is usually packaged with a signalconditioning amplifier in a small module. An APD receivermodule and attendant circuitry appears in Figure 1. TheAPD module (figure right) contains the APD and a transimpedance(e.g., current-to-voltage) amplifier. An opticalport permits interfacing fiberoptic cable to the APD’sphotosensitive portion. The module’s compact constructionfacilitates a direct, low loss connection between theAPD and the amplifier, necessary because of the extremelyhigh speed data rates involved
上传时间： 2013-10-25
上传用户：brain kung
Telecommunication, satellite links and set-top boxes allrequire tuning a high frequency oscillator. The actualtuning element is a varactor diode, a 2-terminal device thatchanges capacitance as a function of reverse bias voltage.1 The oscillator is part of a frequency synthesizingloop, as detailed in Figure 1. A phase locked loop (PLL)compares a divided down representation of the oscillatorwith a frequency reference. The PLL’s output is levelshifted to provide the high voltage necessary to bias thevaractor, which closes a feedback loop by voltage tuningthe oscillator. This loop forces the voltage controlledoscillator (VCO) to operate at a frequency determined bythe frequency reference and the divider’s division ratio.
上传时间： 2013-12-20
上传用户：ABCDE
Providing power for the Pentium® microprocessor family isnot a trivial task by any means. In an effort to simplify thistask we have developed a new switching regulator controlcircuit and a new linear regulator to address the needs ofthese processors. Considerable time has been spent developingan optimized decoupling network. Here are severalcircuits using the new LTC®1266 synchronous buck regulatorcontrol chip and the LT®1584 linear regulator toprovide power for Pentium processors and Pentium VREprocessors. The Pentium processor has a supply requirementof 3.3V ±5%. The Pentium VRE processor requires3.500V ±100mV.
上传时间： 2013-11-01
上传用户：名爵少年
For a variety of reasons, it is desirable to charge batteriesas rapidly as possible. At the same time, overchargingmust be limited to prolong battery life. Such limitation ofovercharging depends on factors such as the choice ofcharge termination technique and the use of multi-rate/multi-stage charging schemes. The majority of batterycharger ICs available today lock the user into one fixedcharging regimen, with at best a limited number ofcustomization options to suit a variety of application needsor battery types. The LTC®1325 addresses these shortcomingsby providing the user with all the functionalblocks needed to implement a simple but highly flexiblebattery charger (see Figure 1) which not only addressesthe issue of charging batteries but also those of batteryconditioning and capacity monitoring.
上传时间： 2013-10-19
上传用户：royzhangsz
锁定放大是微弱信号检测的重要手段。基于相关检测理论，利用开关电容的开关实现锁定放大器中乘法器的功能，提出开关电容和积分器相结合以实现相关检测的方法，并设计出一种锁定放大器。该锁定放大器将微弱信号转化为与之相关的方波，通过后续电路得到正比于被测信号的直流电平，为后续采集处理提供方便。测量数据表明锁定放大器前级可将10-6 A的电流转换为10-1 V的电压，后级通过带通滤波器级联可将信号放大1×105倍。该方法在降低噪声的同时，可对微弱信号进行放大，线性度较高、稳定性较好。 Abstract: Lock-in Amplifying（LIA）is one of important means for weak signal detection. Based on cross-correlation detection theory， switch in the swithched capacitor was used as multiplier of LIA， and a new method of correlation detection was proposed combining swithched capacitor with integrator. A kind of LIA was designed which can convert the weak signal to square-wave， then DC proportional to measured signal was obtained through follow-up conditioning circuit， providing convenience for signal acquisition and processing. The measured data shows that the electric current（10-6 A） can be changed into voltage（10-1 V） by LIA， and the signal is magnified 1×105 times by cascade band-pass filter. The noise is suppressed and the weak signal is amplified. It has the advantages of good linearity and stability.
上传时间： 2013-11-29
上传用户：黑漆漆
Sensing and/or controlling current flow is a fundamental requirement in many electronics systems, and the tech-niques to do so are as diverse as the applications them-selves. This Application Note compiles solutions to cur-rent sensing problems and organizes the solutions by general application type. These circuits have been culled from a variety of Linear Technology documents
标签： 电流检测电路
上传时间： 2013-10-22
上传用户：moshushi0009
The latest generation of Texas Instruments (TI) boardmountedpower modules utilizes a pin interconnect technologythat improves surface-mount manufacturability.These modules are produced as a double-sided surfacemount(DSSMT) subassembly, yielding a case-less constructionwith subcomponents located on both sides of theprinted circuit board (PCB). Products produced in theDSSMT outline use the latest high-efficiency topologiesand magnetic-component packaging. This providescustomers with a high-efficiency, ready-to-use switchingpower module in a compact, space-saving package. Bothnonisolated point-of-load (POL) switching regulators andthe isolated dc/dc converter modules are being producedin the DSSMT outline.TI’s plug-in power product line offers power modules inboth through-hole and surface-mount packages. The surfacemountmodules produced in the DSSMT outline use asolid copper interconnect with an integral solder ball fortheir
上传时间： 2013-10-10
上传用户：1184599859
Permission to make digital or hard copies of all or part of this work forpersonal or classroom use is granted without fee provided that copies arenot made or distributed for profit or commercial advantage and that copiesbear this notice and the full citation on the first page. To copy otherwise, torepublish, to post on servers or to redistribute to lists, requires prior specificpermission.
标签： 数字电源
上传时间： 2013-10-16
上传用户：dddddd
ØCPV is the abbreviation of concentration PV. Ø It utilizes optics to concentrate the sunlight to the CPV cell to generate power. Ø The purpose of CPV is to reduce the cell’s area and the cost of PV module.
上传时间： 2013-10-29
上传用户：开怀常笑
Abstract: This application note describes how to build, debug, and run applications on the on-board MAXQ622microcontroller to interface with the DS8005 dual smart card interface. This is demonstrated in both IAREmbedded Workbench and the Rowley CrossWorks IDE, using sample code provided with the kit.
上传时间： 2013-10-29
上传用户：ddddddd
