Abstract: Mechanical misalignment and scaling factors lead to a mismatch between the values coming from a touchscreen panel (as translated by a touch screen controller) and the display (typically an LCD) on which the touch screenpanel is mounted. This tutorial discusses how to calibrate the touch screen panel to match the display.
上传时间： 2013-10-21
上传用户：euroford
Digital convergence, in recent history, has been prevalentin the consumer equipment domain and the designengineers in this area have been struggling with a plethoraof emerging standards and protocols. What lessons can welearn from their struggle? The same dilemmas now existin in-vehicle telematics and infotainment systems but withthe added issues of extremes of temperature, safety,security, and time in market.
上传时间： 2014-12-23
上传用户：9牛10
This document and the associated reference design provide guidance for assigning anddebugging software to or in FLASH memory, specifically for a MicroBlaze™ embeddedprocessor design.
上传时间： 2013-11-11
上传用户：dgann
High input impedance and a wide input range are twohighly desirable features in a precision analog-to-digitalconverter, and the LTC®2449 delta-sigma ADC has both.With just a few external components, the LTC2449 formsan exceptional measurement system with very high inputimpedance and an input range that extends 300mV beyondthe supply rails.
上传时间： 2013-11-02
上传用户：ywcftc277
A fully differential amplifi er is often used to converta single-ended signal to a differential signal, a designwhich requires three signifi cant considerations: theimpedance of the single-ended source must match thesingle-ended impedance of the differential amplifi er,the amplifi er’s inputs must remain within the commonmode voltage limits and the input signal must be levelshifted to a signal that is centered at the desired outputcommon mode voltage.
上传时间： 2013-11-09
上传用户：wweqas
The MAX2691 low-noise amplifier (LNA) is designed forGPS L2 applications. Designed in Maxim’s advancedSiGe process, the device achieves high gain andlow noise figure while maximizing the input-referred 1dBcompression point and the 3rd-order intercept point. TheMAX2691 provides a high gain of 17.5dB and sub 1dBnoise figure.
标签： Amplifier Low-Noise 2691 Band
上传时间： 2014-12-04
上传用户：zaocan888
Highlights the LTC1062 as a lowpass filter in a phase lock loop. Describes how the loop's bandwidth can be increased and the VCO output jitter reduced when the LTC1062 is the loop filter. Compares it with a passive RC loop filter. Also discussed is the use of LTC1062 as simple bandpass and bandstop filter.
上传时间： 2013-10-24
上传用户：chens000
One of the most critical components in a step-up design like Figure 1 is the transformer. Transformers have parasitic components that can cause them to deviate from their ideal characteristics, and the parasitic capacitance associated with the secondary can cause large resonating current spikes on the leading edge of the switch current waveform.
上传时间： 2013-11-22
上传用户：15070202241
Differential Nonlinearity: Ideally, any two adjacent digitalcodes correspond to output analog voltages that are exactlyone LSB apart. Differential non-linearity is a measure of theworst case deviation from the ideal 1 LSB step. For example,a DAC with a 1.5 LSB output change for a 1 LSB digital codechange exhibits 1⁄2 LSB differential non-linearity. Differentialnon-linearity may be expressed in fractional bits or as a percentageof full scale. A differential non-linearity greater than1 LSB will lead to a non-monotonic transfer function in aDAC.Gain Error (Full Scale Error): The difference between theoutput voltage (or current) with full scale input code and theideal voltage (or current) that should exist with a full scale inputcode.Gain Temperature Coefficient (Full Scale TemperatureCoefficient): Change in gain error divided by change in temperature.Usually expressed in parts per million per degreeCelsius (ppm/°C).Integral Nonlinearity (Linearity Error): Worst case deviationfrom the line between the endpoints (zero and full scale).Can be expressed as a percentage of full scale or in fractionof an LSB.LSB (Lease-Significant Bit): In a binary coded system thisis the bit that carries the smallest value or weight. Its value isthe full scale voltage (or current) divided by 2n, where n is theresolution of the converter.Monotonicity: A monotonic function has a slope whose signdoes not change. A monotonic DAC has an output thatchanges in the same direction (or remains constant) for eachincrease in the input code. the converse is true for decreasing codes.
标签： Converters Defini DAC
上传时间： 2013-10-30
上传用户：stvnash
ANALOG INPUT BANDWIDTH is a measure of the frequencyat which the reconstructed output fundamental drops3 dB below its low frequency value for a full scale input. Thetest is performed with fIN equal to 100 kHz plus integer multiplesof fCLK. The input frequency at which the output is −3dB relative to the low frequency input signal is the full powerbandwidth.APERTURE JITTER is the variation in aperture delay fromsample to sample. Aperture jitter shows up as input noise.APERTURE DELAY See Sampling Delay.BOTTOM OFFSET is the difference between the input voltagethat just causes the output code to transition to the firstcode and the negative reference voltage. Bottom Offset isdefined as EOB = VZT–VRB, where VZT is the first code transitioninput voltage and VRB is the lower reference voltage.Note that this is different from the normal Zero Scale Error.CONVERSION LATENCY See PIPELINE DELAY.CONVERSION TIME is the time required for a completemeasurement by an analog-to-digital converter. Since theConversion Time does not include acquisition time, multiplexerset up time, or other elements of a complete conversioncycle, the conversion time may be less than theThroughput Time.DC COMMON-MODE ERROR is a specification which appliesto ADCs with differential inputs. It is the change in theoutput code that occurs when the analog voltages on the twoinputs are changed by an equal amount. It is usually expressed in LSBs.
上传时间： 2013-11-12
上传用户：pans0ul
