介绍基于ATmega8型单片机的温度测量及加热控制系统。分析系统的工作原理，详尽讨论系统的硬件电路和软件流程。实验证明，该系统工作可靠，稳定性高。 Abstract: The new temperature measuring and heating control system based on ATmega8 MCU is introduced.The system’s working principles is analyzed.The design principles of hardware and software are also discussed in detail.This system has been testified and it works steady and reliably.
上传时间： 2013-11-21
上传用户：caiguoqing
利用Atmel公司的ATmega168微处理器，采用A/D转换方式来实现按摩椅控制器的键盘接口，通过在硬件电路中巧妙地选择电阻，在软件设计中采用数字滤波、二分法和区间鉴定等方法，灵敏可靠地实现了按摩椅中30个按键的处理。给出了硬件电路设计和软件设计思想以及部分汇编代码。 Abstract: This paper chooses A/D conversion method to realize the keyboard interface of the controller by using ATmega168 microchip from Atmel Company.It accomplishes 30-key dealing sensitively and reliably in massage chair through skillfully selecting resistors in hardware circuit and using digital filter,dichotomy and area-judging method in software design.The hardware design circuit, software design idea and partly assembles code are presented mainly.
上传时间： 2014-01-10
上传用户：咔乐坞
利用AT89C51型单片机定时和中断功能，配以LM386型音频功率放大器，构成了作息号音自动播放器，为学校和机关管理提供方便。 Abstract: Using timing and interrupt function of the AT89C51 single-chip microcomputer and the LM386 audio power amplifier.It is constituted the automatic bugle player.This player facilitates the institution and the school daily management.
上传时间： 2013-10-10
上传用户：wivai
对于沥青混凝土摊铺机自动找平控制系统来说，数字式控制系统的研制是目前的一个方向。介绍了一种基于CAN总线的数字式自动找平控制系统。该系统以CAN总线作为通信方式，PWM控制信号通过C8051F040单片机内部PCA可编程计数器阵列产生，并具有结构简单、信号稳定、实时性强、易扩展的特点。通过硬件实现和系统运行达到了比较理想的控制效果，验证了系统的可行性。 Abstract: A digital auto-leveling control system based on CAN Bus is introduced.It uses CAN Bus as the method of communication and creates PWM signals by programmable counter array in C8051F040 microcontroller. The system is simple, stable, real-time and expansive.
上传时间： 2013-10-08
上传用户：ligi201200
介绍以P87LPC764型单片机为核心的延时型漏电继电器设计方案。该方案可供用户选择实现额定动作电流和5倍额定动作电流下不同的延时动作时间，并有重合闸设定选择功能。解决了以往传统分立元件带来的延时时间离散性大且不易实现的弊端。 Abstract: In this paper, the delay leakage relay based on P87LPC764 is introduced in detail. This system provides different relay times at rating current and 5× rating current for users and also offers superposition brake set selection function. So that it resolves many traditional problems.
上传时间： 2013-11-07
上传用户：zhaiye
介绍了CAN总线和P87C591单片机的特点，给出了基于P87C591单片机的信号采集节点的软、硬件设计，指出了硬件电路设计中应注意的问题，在软件设计中重点介绍了节点初始化、报文发送和报文接收等子程序。 Abstract: The features of CAN Bus and the microcontroller P87C591 are introduced, and the design of hardware circuit and soft configuration of the signals collection node based on P87C591 are presented. The problems in designing hardware circuit are discussed.Initialization subprogram, transmiting subprogram and receiving subprogram are emphasized in soft configuration.
上传时间： 2013-11-03
上传用户：BIBI
以S3C825A为例介绍三星公司SAM8系列单片机的内部结构及其软件开发环境，详细描述采用混合编程法来对SAM8系列单片机进行软件设计的一般方法，最后给出用混合编程法对S3C825A进行软件设计的具体应用实例。 Abstract: With S3C825A,this paper firstly introduces the SAM8 series single-chip microcontrollers and their software development environment, then introduces mixed programming technology for SAM8 series single-chip microcontrollers. In the end, the application program is also given.
上传时间： 2013-12-09
上传用户：ZZJ886
基于幅移键控技术ASK（Amplitude-Shift Keying），以C8051F340单片机作为监测终端控制器，C8051F330D单片机作为探测节点控制器，采用半双工的通信方式，通过监控终端和探测节点的无线收发电路，实现数据的双向无线传输。收发电路采用直径为0.8 mm的漆包线自行绕制成圆形空心线圈天线，天线直径为（3.4±0.3）cm。试验表明，探测节点与监测终端的通信距离为24 cm，通过桥接方式，节点收发功率为102 mW时，节点间的通信距离可达20 cm。与传统无线收发模块相比，该无线收发电路在受体积、功耗、成本限制的场合有广阔的应用前景。 Abstract: Based on ASK technology and with the C8051F340 and C8051F330D MCU as the controller， using half-duplex communication mode， this paper achieves bi-directional data transfer. Transceiver circuit constituted by enameled wire which diameter is 0.8mm and wound into a diameter （3.4±0.3） cm circular hollow coil antenna. Tests show that the communication distance between detection and monitoring of the terminal is 24cm，the distance is up to 20cm between two nodes when using the manner of bridging and the node transceiver power is 102mW. Compared with the conventional wireless transceiver modules， the circuit has wide application prospect in small size， low cost and low power consumption and other characteristics.
上传时间： 2013-10-19
上传用户：xz85592677
以ＦＰＧＡ为数字逻辑平台，借助继电器矩阵和多路模拟开关，以ＡＤＳ１２１１为核心，在单片机控制下，联合实现手持式虚拟／智能存储示波表中数字多用表功能，实验表明该设计是行之有效的。文中介绍了数字多用表的系统结构，重点讨论了其测量电路和智能控制方案。 Abstract: Ｔｈｅ ｄｉｇｉｔａｌ ｍｕｌｔｉｍｅｔｅｒ ｉｎ ｖｉｒｔｕａｌ／ｉｎｔｅｌｌｅｃｔ ｄｉｇｉｔａｌ－ｏｓｃｉｌｌｏｒｇａｐｈ ｗａｓ ｆｕｌｆｉｌｌｅｄ, ｗｈｉｃｈ ｗａｓ ｃｏｎｔｒｏｌｌｅｄ ｂｙ ｓｉｎｇｌｅｃｈｉｐ ｃｏｍｐｕｔｅｒ ｂｙ ｒｅｌａｙ ｍａｔｒｉｘ ａｎｄ ａｎａｌｏｇｕｅ ｓｗｉｔｃｈｅｓ,ｉｎ ｗｈｉｃｈ ＦＰＧＡ ｗａｓ ｕｓｅｄ ｆｏｒ ｄｉｇｉｔａｌ ｌｏｇｉｃａｌ ｐｌｏｔ-ｆｏｒｍ, ＡＤＳ１２１１ ｆｏｒ ｋｅｒｎｅｌ ｃｈｉｐ, ｔｈｅ ｅｘｐｅｒｉｍｅｎｔ ｓｈｏｗｅｄ ｔｈｅ ｄｅｓｉｇｎ ｗａｓ ｆｅａｓｉｂｌｅ, ｔｈｅ ｓｙｓｔｅｍ ｓｔｒｕｃｔｉｏｎ ｗａｓ ｐｒｅｓｅｎｔ-ｅｄ ｉｎ ｔｈｅ ｐａｐｅｒ, ｍｅａｓｕｒｅ ｃｉｒｃｕｉｔ ａｎｄ ｉｎｔｅｌｌｅｃｔ ｃｏｎｔｒｏｌ ｐｌａｎ ｏｆ ｄｉｇｉｔａｌ ｍｕｌｔｉｍｅｔｅｒ ｗｅｒｅ ｍａｉｎｌｙ ｇｉｖｅｎ．
上传时间： 2013-11-02
上传用户：瓦力瓦力hong
在需要实时大量输入汉字的显示控制处理应用中，利用传统单片机实现显示控制的设计方法是较难实现的。带汉字字库的液晶模块的使用使得小容量ROM单片机的大量汉字信息输入与显示成为可能。提出了针对汉字字库编码的二级索引拼音输入检索方法,介绍了以ST7920作为控制器的带汉字字库的液晶显示模块的接口方法及汉字显示和控制原理，给出了通用计算机键盘在单片机中的串行接口，采用该技术可大大增强单片机的汉字输入功能。为小容量ROM单片机的大批量汉字信息处理提供了一种汉字输入解决方案。 Abstract: It is difficult to realize Chinese characters input method based on the embedded system by using the traditional design method of display control. It is possible to input and display Chinese characters based on the embedded system with the ROM of small content by using the LCD module with Chinese characters.Chinese characters input method of the quadric index recall in allusion to Chinese characters code is brought forward.The interface and the principle of Chinese characters display control based on the LCD module controlled with the ST7920 is introduced too.The serial interface of the computer keyboard in common use and the embedded system is given at the same time. It can enhance the embedded system function of Chinese characters input by using this technology, and provide a kind of Chinese characters input scheme for the embedded system with small capacity ROM.
上传时间： 2013-11-18
上传用户：jhksyghr
