What would happen if someone connected 24V to your12V circuits? If the power and ground lines were inadvertentlyreversed, would the circuits survive? Does yourapplication reside in a harsh environment, where the inputsupply can ring very high or even below ground? Evenif these events are unlikely, it only takes one to destroya circuit board.
上传时间： 2013-10-26
上传用户：jackandlee
Specifying the right reference and applying it correctly isa more difficult task than one might first surmise, consideringthat references are only 2- or 3-terminal devices.Although the word “accuracy” is most often spoken inreference to references, it is dangerous to use this wordtoo freely because it can mean different things to differentpeople. Even more perplexing is the fact that a referenceclassified as a dog in one application is a panacea inanother. This application note will familiarize the readerwith the various aspects of reference “accuracy” andpresent some tips on extracting maximum performancefrom any reference.
标签： 电压基准
上传时间： 2013-10-15
上传用户：liuwei6419
Designers spend much time combating thermal effects incircuitry. The close relationship between temperature andelectronic devices is the source of more design headachesthan any other consideration.
上传时间： 2013-10-17
上传用户：风之骄子
A frequent requirement in systems involves drivinganalog signals into non-linear or reactive loads. Cables,transformers, actuators, motors and sample-hold circuitsare examples where the ability to drive diffi cult loads isrequired. Although several power buffer amplifi ers areavailable, none have been optimized for driving diffi cultloads.
上传时间： 2014-12-24
上传用户：1109003457
Abstract: As electronic systems take over many of the mechanical functions in a car—ranging from engine timing to steering andbraking—there is a growing concern about fault tolerance. There should not be a single point of failure that would prevent a car fromat least "limping" off the road or making it to the nearest service station. Redundant systems, watchdog timers, and other controlcircuits are used to reroute signals and perform other functions that ensure that a vehicle can safely make it off the road when afailure occurs.
上传时间： 2013-11-10
上传用户：diets
Abstract: This article discusses future trends in the design of smartphones and other consumer products. The discussion focuses onthe importance of integration, which saves valuable PCB space and drives down costs.
上传时间： 2014-01-13
上传用户：lhw888
The voltage range of Linear Technology’s PowerPath® circuitscan be easily extended with just a few components, thusallowing them to meet the needs of virtually all applications.This application note presents solutions for circuits thatmust withstand large negative voltages, a reverse adapterinput for example, and circuits that must withstand largepositive inputs, such as automotive load-dump.
上传时间： 2013-10-21
上传用户：几何公差
In a recent discussion with a system designer, the requirementfor his power supply was to regulate 1.5Vand deliver up to 40A of current to a load that consistedof four FPGAs. This is up to 60W of power that must bedelivered in a small area with the lowest height profi lepossible to allow a steady fl ow of air for cooling. Thepower supply had to be surface mountable and operateat high enough effi ciency to minimize heat dissipation.He also demanded the simplest possible solution so histime could be dedicated to the more complex tasks. Asidefrom precise electrical performance, this solution had toremovethe heat generated during DC to DC conversionquickly so that the circuit and the ICs in the vicinity do notoverheat. Such a solution requires an innovative designto meet these criteria:
上传时间： 2013-11-24
上传用户：defghi010
Avalanche photodiodes (APDs) are widely utilized in laserbased fiberoptic systems to convert optical data intoelectrical form. The APD is usually packaged with a signalconditioning amplifier in a small module. An APD receivermodule and attendant circuitry appears in Figure 1. TheAPD module (figure right) contains the APD and a transimpedance(e.g., current-to-voltage) amplifier. An opticalport permits interfacing fiberoptic cable to the APD’sphotosensitive portion. The module’s compact constructionfacilitates a direct, low loss connection between theAPD and the amplifier, necessary because of the extremelyhigh speed data rates involved
上传时间： 2013-10-25
上传用户：brain kung
Occasionally, we are tasked with designing circuitry for aspecific purpose. The request may have customer originsor it may be an in-house requirement. Alternately, a circuitmay be developed because its possibility is simply tooattractive to ignore1. Over time, these circuits accumulate,encompassing a wide and useful body of proven capabilities.They also represent substantial effort. These considerationsmake publication an almost obligatory propositionand, as such, a group of circuits is presented here. This isnot the first time we have displayed such wares and, giventhe encouraging reader response, it will not be the last2.Eighteen circuits are included in this latest effort, roughlyarranged in the categories given in this publication’s title.They appear at the next paragraph.
上传时间： 2013-11-12
上传用户：012345
