All inputs of the C16x family have Schmitt-Trigger input characteristics. These Schmitt-Triggers are intended to always provide proper internal low and high levels, even if anundefined voltage level (between TTL-VIL and TTL-VIH) is externally applied to the pin.The hysteresis of these inputs, however, is very small, and can not be properly used in anapplication to suppress signal noise, and to shape slow rising/falling input transitions.Thus, it must be taken care that rising/falling input signals pass the undefined area of theTTL-specification between VIL and VIH with a sufficient rise/fall time, as generally usualand specified for TTL components (e.g. 74LS series: gates 1V/us, clock inputs 20V/us).The effect of the implemented Schmitt-Trigger is that even if the input signal remains inthe undefined area, well defined low/high levels are generated internally. Note that allinput signals are evaluated at specific sample points (depending on the input and theperipheral function connected to it), at that signal transitions are detected if twoconsecutive samples show different levels. Thus, only the current level of an input signalat these sample points is relevant, that means, the necessary rise/fall times of the inputsignal is only dependant on the sample rate, that is the distance in time between twoconsecutive evaluation time points. If an input signal, for instance, is sampled throughsoftware every 10us, it is irrelevant, which input level would be seen between thesamples. Thus, it would be allowable for the signal to take 10us to pass through theundefined area. Due to the sample rate of 10us, it is assured that only one sample canoccur while the signal is within the undefined area, and no incorrect transition will bedetected. For inputs which are connected to a peripheral function, e.g. capture inputs, thesample rate is determined by the clock cycle of the peripheral unit. In the case of theCAPCOM unit this means a sample rate of 400ns @ 20MHz CPU clock. This requiresinput signals to pass through the undefined area within these 400ns in order to avoidmultiple capture events.For input signals, which do not provide the required rise/fall times, external circuitry mustbe used to shape the signal transitions.In the attached diagram, the effect of the sample rate is shown. The numbers 1 to 5 in thediagram represent possible sample points. Waveform a) shows the result if the inputsignal transition time through the undefined TTL-level area is less than the time distancebetween the sample points (sampling at 1, 2, 3, and 4). Waveform b) can be the result ifthe sampling is performed more than once within the undefined area (sampling at 1, 2, 5,3, and 4).Sample points:1. Evaluation of the signal clearly results in a low level2. Either a low or a high level can be sampled here. If low is sampled, no transition willbe detected. If the sample results in a high level, a transition is detected, and anappropriate action (e.g. capture) might take place.3. Evaluation here clearly results in a high level. If the previous sample 2) had alreadydetected a high, there is no change. If the previous sample 2) showed a low, atransition from low to high is detected now.
上传时间： 2013-10-23
上传用户：copu
This document describes part number speciÞc changes to recommended operating conditions and revised electrical speciÞcations,as applicable, from those described in the generalMPC7400 Hardware SpeciÞcations.SpeciÞcations provided in this Part Number SpeciÞcation supersede those in theMPC7400 Hardware SpeciÞcationsdated 9/99(order #: MPC7400EC/D) for these part numbers only; speciÞcations not addressed herein are unchanged. This document isfrequently updated, refer to the website at http://www.mot.com/SPS/PowerPC/ for the latest version.Note that headings and table numbers in this data sheet are not consecutively numbered. They are intended to correspond to theheading or table affected in the general hardware speciÞcation.Part numbers addressed in this document are listed in Table A. For more detailed ordering information see Table B.
上传时间： 2013-11-19
上传用户：qiaoyue
The Kannel Open Source WAP and SMS gateway works as both an SMS gateway, for implementing keyword based services via GSM text messages, and a WAP gateway, via UDP. The SMS part is fairly mature, the WAP part is early in its development. In this release, the GET request for WML pages and WMLScript files via HTTP works, including compilation for WML and WMLScript to binary forms. Only the data call bearer (UDP) is supported, not SMS.
标签： gateway implementing SMS keyword
上传时间： 2014-01-11
上传用户：2525775
USB海量存储设备类规范包括四个独立的子类规范：(ATA command的那个没有) ①USB Mass Storgage Class Control/Bulk/Interrupt(CBI)Transport ②USB Mass Storage Class Bulk-Only Transport ③USB Mass Storage Class ATA Command Block ④USB Mass Stroage Class UFI Command Specification。 前两个子规范定义了数据/命令/状态在USB上的传输方法。 Bulk-Only传输规范仅仅使用Bulk端点传送数据/命令/状态， CBI传输规范则使用Control/Bulk/Interrupt三种类型的端点进行数据/命令/状态传送。 后两个子规范定义了对存储介质的操作命令。 ATA 命令规范用于硬盘。 UFI命令规范是针对USB移动存储而制定的，实际上UFI命令格式是基于SFF-8070i和SCSI-2规范，总共定义了19个12字节长度的操作命令。
标签： USB Interrupt Storgage Control
上传时间： 2015-08-29
上传用户：aysyzxzm
The task of clustering Web sessions is to group Web sessions based on similarity and consists of maximizing the intra- group similarity while minimizing the inter-group similarity． The first and foremost question needed to be considered in clustering W b sessions is how to measure the similarity between Web sessions．However．there are many shortcomings in traditiona1 measurements．This paper introduces a new method for measuring similarities between Web pages that takes into account not only the URL but also the viewing time of the visited web page．Yhen we give a new method to measure the similarity of Web sessions using sequence alignment and the similarity of W eb page access in detail Experiments have proved that our method is valid and e币cient．
标签： sessions clustering similarity Web
上传时间： 2014-01-11
上传用户：songrui
A Convex Hull is the smallest convex polygon that contains every point of the set S. A polygon P is convex if and only if, for any two points A and B inside the polygon, the line segment AB is inside P. One way to visualize a convex hull is to put a "rubber band" around all the points, and let it wrap as tight as it can. The resultant polygon is a convex hull.
上传时间： 2013-12-23
上传用户：it男一枚
Abstract-In this paper, simple autonomous chaotic circuits coupled by resistors are investigated. By carrying out computer calculations and circuit experiments, irregular self-switching phenomenon of three spatial patterns characterized by the phase states of quasi-synchronization of chaos can be observed from only four simple chaotic circuits. This is the same phenomenon as chaotic wandering of spatial patterns observed very often from systems with a large number of degrees of freedom. Namely, one of spatial-temporal chaos observed from systems of large size can be also generated in the proposed system consisting of only four chaotic circuits. A six subcircuits case and a coupled chaotic circuits networks are also studied, and such systems are confirmed to produce more complicated spatio-temporal phenomena.
标签： investigated Abstract-In autonomous resistors
上传时间： 2014-06-09
上传用户：h886166
GRE 数学圣经，下面是详细的英文介绍： Comprehensive Prep for GRE Math Every year, students pay $1,000 and more to test prep companies to prepare for the math section of the GRE. Now you can get the same preparation in a book. Although the GRE math section is difficult, it is very learnable. GRE Math Bible presents a thorough analysis of GRE math and introduces numerous analytic techniques that will help you immensely, not only on the GRE but in graduate school as well.
标签： GRE Math 数学
上传时间： 2015-08-22
上传用户：东大寺的
/* ********************************************************************************************************* * uC/TCP-IP V2 * The Embedded TCP/IP Suite * * (c) Copyright 2003-2010; Micrium, Inc.; Weston, FL * * All rights reserved. Protected by international copyright laws. * * uC/TCP-IP is provided in source form to registered licensees ONLY. It is * illegal to distribute this source code to any third party unless you receive * written permission by an authorized Micrium representative. Knowledge of * the source code may NOT be used to develop a similar product. * * Please help us continue to provide the Embedded community with the finest * software available. Your honesty is greatly appreciated. * * You can contact us at www.micrium.com. ********************************************************************************************************* */ /* ********************************************************************************************************* * * NETWORK TCP LAYER * (TRANSMISSION CONTROL PROTOCOL) * * Filename : net_tcp.h * Version : V2.10 * Programmer(s) : ITJ ********************************************************************************************************* * Note(s) : (1) Supports Transmission Control Protocol as described in RFC #793 with the following * restrictions/constraints : * * (a) TCP Security & Precedence NOT supported RFC # 793, Section 3.6 * * (b) TCP Urgent Data NOT supported RFC # 793, Section 3.7 * 'The Communication of * Urgent Information' * * (c) The following TCP options NOT supported : * * (1) Window Scale RFC #1072, Section 2 * RFC #1323, Section 2 * (2) Selective Acknowledgement (SACK) RFC #1072, Section 3 * RFC #2018 * RFC #2883 * (3) TCP Echo RFC #1072, Section 4 * (4) Timestamp RFC #1323, Section 3.2 * (5) Protection Against Wrapped Sequences (PAWS) RFC #1323, Section 4 * * (d) #### IP-Options-to-TCP-Connection RFC #1122, Section 4.2.3.8 * Handling NOT supported * * (e) #### ICMP-Error-Message-to-TCP-Connection RFC #1122, Section 4.2.3.9 * Handling NOT currently supported * * (2) TCP Layer assumes/requires Network Socket Layer (see 'net_sock.h MODULE Note #1a2'). ********************************************************************************************************* */ /*$PAGE*/ /* ********************************************************************************************************* * MODULE * * Note(s) : (1) TCP Layer module is NOT required for UDP-to-Application API configuration. * * See also 'net_cfg.h TRANSPORT LAYER CONFIGURATION' * & 'net_cfg.h USER DATAGRAM PROTOCOL LAYER CONFIGURATION'. * * See also 'net_tcp.h Note #2'. * * (2) The following TCP-module-present configuration value MUST be pre-#define'd in * 'net_cfg_net.h' PRIOR to all other network modules that require TCP Layer * configuration (see 'net_cfg_net.h TCP LAYER CONFIGURATION Note #2b') : * * NET_TCP_MODULE_PRESENT ********************************************************************************************************* */ #ifdef NET_TCP_MODULE_PRESENT /* See Note #2. */ /* ********************************************************************************************************* * EXTERNS ********************************************************************************************************* */ #if ((defined(NET_TCP_MODULE)) && \ (defined(NET_GLOBALS_EXT))) #define NET_TCP_EXT #else #define NET_TCP_EXT extern #endif /*$PAGE*/ /* ********************************************************************************************************* * DEFINES ********************************************************************************************************* */ /* ********************************************************************************************************* * TCP HEADER DEFINES * * Note(s) : (1) The following TCP value MUST be pre-#define'd in 'net_def.h' PRIOR to 'net_buf.h' so that * the Network Buffer Module can configure maximum buffer header size (see 'net_def.h TCP * LAYER DEFINES' & 'net_buf.h NETWORK BUFFER INDEX & SIZE DEFINES Note #1') : * * (a) NET_TCP_HDR_SIZE_MAX 60 (NET_TCP_HDR_LEN_MAX * * NET_TCP_HDR_LEN_WORD_SIZE) * * (2) Urgent pointer & data NOT supported (see 'net_tcp.h Note #1b'). ********************************************************************************************************* */ #define NET_TCP_HDR_LEN_MASK 0xF000u #define NET_TCP_HDR_LEN_SHIFT 12u #define NET_TCP_HDR_LEN_NONE 0u #define NET_TCP_HDR_LEN_MIN 5u #define NET_TCP_HDR_LEN_MAX 15u #define NET_TCP_HDR_LEN_WORD_SIZE CPU_WORD_SIZE_32 #define NET_TCP_HDR_SIZE_MIN (NET_TCP_HDR_LEN_MIN * NET_TCP_HDR_LEN_WORD_SIZE) #if 0 /* See Note #1a. */ #define NET_TCP_HDR_SIZE_MAX (NET_TCP_HDR_LEN_MAX * NET_TCP_HDR_LEN_WORD_SIZE) #endif #define NET_TCP_HDR_SIZE_TOT_MIN (NET_IP_HDR_SIZE_TOT_MIN + NET_TCP_HDR_SIZE_MIN) #define NET_TCP_HDR_SIZE_TOT_MAX (NET_IP_HDR_SIZE_TOT_MAX + NET_TCP_HDR_SIZE_MAX) #define NET_TCP_PSEUDO_HDR_SIZE 12u /* = sizeof(NET_TCP_PSEUDO_HDR) */ #define NET_TCP_PORT_NBR_RESERVED NET_PORT_NBR_RESERVED #define NET_TCP_PORT_NBR_NONE NET_TCP_PORT_NBR_RESERVED #define NET_TCP_HDR_URG_PTR_NONE 0x0000u /* See Note #2. */ /*$PAGE*/ /* ********************************************************************************************************* * TCP HEADER FLAG DEFINES * * Note(s) : (1) See 'TCP HEADER Note #2' for flag fields. * * (2) Urgent pointer & data NOT supported (see 'net_tcp.h Note #1b'). ********************************************************************************************************* */ #define NET_TCP_HDR_FLAG_MASK 0x0FFFu #define NET_TCP_HDR_FLAG_NONE DEF_BIT_NONE #define NET_TCP_HDR_FLAG_RESERVED 0x0FE0u /* MUST be '0'. */ #define NET_TCP_HDR_FLAG_URGENT DEF_BIT_05 /* See Note #2. */ #define NET_TCP_HDR_FLAG_ACK DEF_BIT_04 #define NET_TCP_HDR_FLAG_PUSH DEF_BIT_03 #define NET_TCP_HDR_FLAG_RESET DEF_BIT_02 #define NET_TCP_HDR_FLAG_SYNC DEF_BIT_01 #define NET_TCP_HDR_FLAG_FIN DEF_BIT_00 #define NET_TCP_HDR_FLAG_CLOSE NET_TCP_HDR_FLAG_FIN /* ********************************************************************************************************* * TCP FLAG DEFINES ********************************************************************************************************* */ /* ------------------ NET TCP FLAGS ------------------- */ #define NET_TCP_FLAG_NONE DEF_BIT_NONE #define NET_TCP_FLAG_USED DEF_BIT_00 /* TCP conn cur used; i.e. NOT in free TCP conn pool. */ /* ------------------ TCP TX FLAGS ------------------- */ /* TCP tx flags copied from TCP hdr flags. */ #define NET_TCP_FLAG_TX_FIN NET_TCP_HDR_FLAG_FIN #define NET_TCP_FLAG_TX_CLOSE NET_TCP_FLAG_TX_FIN #define NET_TCP_FLAG_TX_SYNC NET_TCP_HDR_FLAG_SYNC #define NET_TCP_FLAG_TX_RESET NET_TCP_HDR_FLAG_RESET #define NET_TCP_FLAG_TX_PUSH NET_TCP_HDR_FLAG_PUSH #define NET_TCP_FLAG_TX_ACK NET_TCP_HDR_FLAG_ACK #define NET_TCP_FLAG_TX_URGENT NET_TCP_HDR_FLAG_URGENT #define NET_TCP_FLAG_TX_BLOCK DEF_BIT_07 /* ------------------ TCP RX FLAGS ------------------- */ #define NET_TCP_FLAG_RX_DATA_PEEK DEF_BIT_08 #define NET_TCP_FLAG_RX_BLOCK DEF_BIT_15 /*$PAGE*/ /* ********************************************************************************************************* * TCP TYPE DEFINES * * Note(s) : (1) NET_TCP_TYPE_&&& #define values specifically chosen as ASCII representations of the TCP * types. Memory displays of TCP types will display with their chosen ASCII names. ********************************************************************************************************* */ /* ------------------ NET TCP TYPES ------------------- */ #if (CPU_CFG_ENDIAN_TYPE == CPU_ENDIAN_TYPE_BIG) #define NET_TCP_TYPE_NONE 0x4E4F4E45u /* "NONE" in ASCII. */ #define NET_TCP_TYPE_CONN 0x54435020u /* "TCP " in ASCII. */ #else #if (CPU_CFG_DATA_SIZE == CPU_WORD_SIZE_32) #define NET_TCP_TYPE_NONE 0x454E4F4Eu /* "NONE" in ASCII. */ #define NET_TCP_TYPE_CONN 0x20504354u /* "TCP " in ASCII. */ #elif (CPU_CFG_DATA_SIZE == CPU_WORD_SIZE_16) #define NET_TCP_TYPE_NONE 0x4F4E454Eu /* "NONE" in ASCII. */ #define NET_TCP_TYPE_CONN 0x43542050u /* "TCP " in ASCII. */ #else /* Dflt CPU_WORD_SIZE_08. */ #define NET_TCP_TYPE_NONE 0x4E4F4E45u /* "NONE" in ASCII. */ #define NET_TCP_TYPE_CONN 0x54435020u /* "TCP " in ASCII. */ #endif #endif /* ********************************************************************************************************* * TCP SEQUENCE NUMBER DEFINES * * Note(s) : (1) TCP initial transmit sequence number is incremented by a fixed value, preferably a large * prime value or a large value with multiple unique factors. * * (a) One reasonable TCP initial transmit sequence number increment value example : * * 65527 = 37 * 23 * 11 * 7 * * * #### NET_TCP_TX_SEQ_NBR_CTR_INC could be developer-configured in 'net_cfg.h'. * * See also 'NET_TCP_TX_GET_SEQ_NBR() Notes #1b2 & #1c2'. ********************************************************************************************************* */ #define NET_TCP_SEQ_NBR_NONE 0u #define NET_TCP_ACK_NBR_NONE NET_TCP_SEQ_NBR_NONE #define NET_TCP_TX_SEQ_NBR_CTR_INC 65527u /* See Note #1. */ #define NET_TCP_ACK_NBR_DUP_WIN_SIZE_SCALE 4 /*$PAGE*/ /* ********************************************************************************************************* * TCP DATA/TOTAL LENGTH DEFINES * * Note(s) : (1) (a) TCP total length #define's (NET_TCP_TOT_LEN) relate to the total size of a complete * TCP packet, including the packet's TCP header. Note that a complete TCP packet MAY * be fragmented in multiple Internet Protocol packets. * * (b) TCP data length #define's (NET_TCP_DATA_LEN) relate to the data size of a complete * TCP packet, equal to the total TCP packet length minus its TCP header size. Note * that a complete TCP packet MAY be fragmented in multiple Internet Protocol packets. ********************************************************************************************************* */ /* See Notes #1a & #1b. */ #define NET_TCP_DATA_LEN_MIN 0u #define NET_TCP_TOT_LEN_MIN (NET_TCP_HDR_SIZE_MIN + NET_TCP_DATA_LEN_MIN) #define NET_TCP_TOT_LEN_MAX (NET_IP_TOT_LEN_MAX - NET_IP_HDR_SIZE_MIN ) #define NET_TCP_DATA_LEN_MAX (NET_TCP_TOT_LEN_MAX - NET_TCP_HDR_SIZE_MIN) /*$PAGE*/ /* ********************************************************************************************************* * TCP SEGMENT SIZE DEFINES * * Note(s) : (1) (a) RFC # 879, Section 3 states that the TCP Maximum Segment Size "counts only * data octets in the segment, ... not the TCP header or the IP header". * * (b) RFC #1122, Section 4.2.2.6 requires that : * * (1) "The MSS value to be sent in an MSS option must be less than or equal to * * (A) MMS_R - 20 * * where MMS_R is the maximum size for a transport-layer message that can * be received." * * (2) "If an MSS option is not received at connection setup, TCP MUST assume a * default send MSS of 536 (576 - 40)." * * See also 'net_ip.h IP DATA/TOTAL LENGTH DEFINES Note #1'. ********************************************************************************************************* */ /* See Note #1. */ #define NET_TCP_MAX_SEG_SIZE_DFLT (NET_IP_MAX_DATAGRAM_SIZE_DFLT - NET_IP_HDR_SIZE_MIN - NET_TCP_HDR_SIZE_MIN) #define NET_TCP_MAX_SEG_SIZE_DFLT_RX NET_TCP_DATA_LEN_MAX /* See Note #1b1. */ #define NET_TCP_MAX_SEG_SIZE_DFLT_TX NET_TCP_MAX_SEG_SIZE_DFLT /* See Note #1b2. */ #define NET_TCP_MAX_SEG_SIZE_NONE 0u #define NET_TCP_MAX_SEG_SIZE_MIN NET_TCP_MAX_SEG_SIZE_DFLT #define NET_TCP_MAX_SEG_SIZE_MAX NET_TCP_DATA_LEN_MAX #define NET_TCP_SEG_LEN_MIN NET_TCP_DATA_LEN_MIN #define NET_TCP_SEG_LEN_MAX NET_TCP_DATA_LEN_MAX #define NET_TCP_SEG_LEN_SYNC 1u #define NET_TCP_SEG_LEN_FIN 1u #define NET_TCP_SEG_LEN_CLOSE NET_TCP_SEG_LEN_FIN #define NET_TCP_SEG_LEN_ACK 0u #define NET_TCP_SEG_LEN_RESET 0u #define NET_TCP_SEG_LEN_PROBE 0u #define NET_TCP_DATA_LEN_TX_SYNC 0u #define NET_TCP_DATA_LEN_TX_FIN 0u #define NET_TCP_DATA_LEN_TX_CLOSE NET_TCP_DATA_LEN_TX_FIN #define NET_TCP_DATA_LEN_TX_ACK 0u #define NET_TCP_DATA_LEN_TX_PROBE_NO_DATA 0u #define NET_TCP_DATA_LEN_TX_PROBE_DATA 1u #define NET_TCP_DATA_LEN_TX_RESET 0u #define NET_TCP_TX_PROBE_DATA 0x00u /* ********************************************************************************************************* * TCP WINDOW SIZE DEFINES * * Note(s) : (1) Although NO RFC specifies the absolute minimum TCP connection window size value allowed, * RFC #793, Section 3.7 'Data Communication : Managing the Window' states that for "the * window ... there is an assumption that this is related to the currently available data * buffer space available for this connection". ********************************************************************************************************* */ #define NET_TCP_WIN_SIZE_NONE 0u #define NET_TCP_WIN_SIZE_MIN NET_TCP_MAX_SEG_SIZE_MIN #define NET_TCP_WIN_SIZE_MAX DEF_INT_16U_MAX_VAL /*$PAGE*/ /* ********************************************************************************************************* * TCP HEADER OPTIONS DEFINES * * Note(s) : (1) See the following RFC's for TCP options summary : * * (a) RFC # 793, Section 3.1 'Header Format : Options' * (b) RFC #1122; Sections 4.2.2.5, 4.2.2.6 * * (2) TCP option types are encoded in the first octet for each TCP option as follows : * * -------- * | TYPE | * -------- * * The TCP option type value determines the TCP option format : * * (a) The following TCP option types are single-octet TCP options -- i.e. the option type * octet is the ONLY octet for the TCP option. * * (1) TYPE = 0 End of Options List * (2) TYPE = 1 No Operation * * * (b) All other TCP options MUST be multi-octet TCP options (see RFC #1122, Section 4.2.2.5) : * * ------------------------------ * | TYPE | LEN | TCP OPT | * ------------------------------ * * where * TYPE Indicates the specific TCP option type * LEN Indicates the total TCP option length, in octets, including * the option type & the option length octets * TCP OPT Additional TCP option octets, if any, that contain the remaining * TCP option information * * The following TCP option types are multi-octet TCP options where the option's second * octet specify the total TCP option length, in octets, including the option type & the * option length octets : * * (1) TYPE = 2 Maximum Segment Size See RFC # 793, Section 3.1 'Header Format : * Options : Maximum Segment Size'; * RFC #1122, Section 4.2.2.6; * RFC # 879, Section 3 * * (2) TYPE = 3 Window Scale See 'net_tcp.h Note #1c1' * (3) TYPE = 4 SACK Allowed See 'net_tcp.h Note #1c2' * (4) TYPE = 5 SACK Option See 'net_tcp.h Note #1c2' * (5) TYPE = 6 Echo Request See 'net_tcp.h Note #1c3' * (6) TYPE = 7 Echo Reply See 'net_tcp.h Note #1c3' * (7) TYPE = 8 Timestamp See 'net_tcp.h Note #1c4' * * (3) TCP header allows for a maximum option list length of 40 octets : * * NET_TCP_HDR_OPT_SIZE_MAX = NET_TCP_HDR_SIZE_MAX - NET_TCP_HDR_SIZE_MIN * * = 60 - 20 * * = 40 * * (4) 'NET_TCP_OPT_SIZE' MUST be pre-defined PRIOR to all definitions that require TCP option * size data type. ********************************************************************************************************* */ /*$PAGE*/ #define NET_TCP_HDR_OPT_END_LIST 0u #define NET_TCP_HDR_OPT_NOP 1u #define NET_TCP_HDR_OPT_MAX_SEG_SIZE 2u #define NET_TCP_HDR_OPT_WIN_SCALE 3u #define NET_TCP_HDR_OPT_SACK_PERMIT 4u #define NET_TCP_HDR_OPT_SACK 5u #define NET_TCP_HDR_OPT_ECHO_REQ 6u #define NET_TCP_HDR_OPT_ECHO_REPLY 7u #define NET_TCP_HDR_OPT_TS 8u #define NET_TCP_HDR_OPT_PAD NET_TCP_HDR_OPT_END_LIST #define NET_TCP_HDR_OPT_LEN_END_LIST 1u #define NET_TCP_HDR_OPT_LEN_NOP 1u #define NET_TCP_HDR_OPT_LEN_MAX_SEG_SIZE 4u #define NET_TCP_HDR_OPT_LEN_WIN_SCALE 3u #define NET_TCP_HDR_OPT_LEN_SACK_PERMIT 2u #define NET_TCP_HDR_OPT_LEN_ECHO_REQ 6u #define NET_TCP_HDR_OPT_LEN_ECHO_REPLY 6u #define NET_TCP_HDR_OPT_LEN_TS 10u #define NET_TCP_HDR_OPT_LEN_SACK_MIN 6u #define NET_TCP_HDR_OPT_LEN_SACK_MAX 38u #define NET_TCP_HDR_OPT_LEN_MIN 1u #define NET_TCP_HDR_OPT_LEN_MIN_LEN 2u #define NET_TCP_HDR_OPT_LEN_MAX 38u typedef CPU_INT32U NET_TCP_OPT_SIZE; /* TCP opt size data type (see Note #4). */ #define NET_TCP_HDR_OPT_SIZE_WORD (sizeof(NET_TCP_OPT_SIZE)) #define NET_TCP_HDR_OPT_SIZE_MAX (NET_TCP_HDR_SIZE_MAX - NET_TCP_HDR_SIZE_MIN) #define NET_TCP_HDR_OPT_NBR_MIN 0u #define NET_TCP_HDR_OPT_NBR_MAX (NET_TCP_HDR_OPT_SIZE_MAX / NET_TCP_HDR_OPT_SIZE_WORD) #define NET_TCP_HDR_OPT_IX NET_TCP_HDR_SIZE_MIN /*$PAGE*/ /* ********************************************************************************************************* * TCP OPTION CONFIGURATION TYPE DEFINES * * Note(s) : (1) NET_TCP_OPT_CFG_TYPE_&&& #define values specifically chosen as ASCII representations of * the TCP option configuration types. Memory displays of TCP option configuration buffers * will display the TCP option configuration TYPEs with their chosen ASCII names. ********************************************************************************************************* */ /* ---------------- TCP OPT CFG TYPES ----------------- */ #if (CPU_CFG_ENDIAN_TYPE == CPU_ENDIAN_TYPE_BIG) #define NET_TCP_OPT_CFG_TYPE_NONE 0x4E4F4E45u /* "NONE" in ASCII. */ #define NET_TCP_OPT_CFG_TYPE_MAX_SEG_SIZE 0x4D535320u /* "MSS " in ASCII. */ #define NET_TCP_OPT_CFG_TYPE_WIN_SCALE 0x57494E20u /* "WIN " in ASCII (see 'net_tcp.h Note #1c1'). */ #define NET_TCP_OPT_CFG_TYPE_SACK_PERMIT 0x53434B50u /* "SCKP" in ASCII (see 'net_tcp.h Note #1c2'). */ #define NET_TCP_OPT_CFG_TYPE_SACK 0x5341434Bu /* "SACK" in ASCII (see 'net_tcp.h Note #1c2'). */ #define NET_TCP_OPT_CFG_TYPE_ECHO_REQ 0x45524551u /* "EREQ" in ASCII (see 'net_tcp.h Note #1c3'). */ #define NET_TCP_OPT_CFG_TYPE_ECHO_REPLY 0x4543484Fu /* "ECHO" in ASCII (see 'net_tcp.h Note #1c3'). */ #define NET_TCP_OPT_CFG_TYPE_TS 0x54532020u /* "TS " in ASCII (see 'net_tcp.h Note #1c4'). */ #else #if (CPU_CFG_DATA_SIZE == CPU_WORD_SIZE_32) #define NET_TCP_OPT_CFG_TYPE_NONE 0x454E4F4Eu /* "NONE" in ASCII. */ #define NET_TCP_OPT_CFG_TYPE_MAX_SEG_SIZE 0x2053534Du /* "MSS " in ASCII. */ #define NET_TCP_OPT_CFG_TYPE_WIN_SCALE 0x204E4957u /* "WIN " in ASCII (see 'net_tcp.h Note #1c1'). */ #define NET_TCP_OPT_CFG_TYPE_SACK_PERMIT 0x504B4353u /* "SCKP" in ASCII (see 'net_tcp.h Note #1c2'). */ #define NET_TCP_OPT_CFG_TYPE_SACK 0x4B434153u /* "SACK" in ASCII (see 'net_tcp.h Note #1c2'). */ #define NET_TCP_OPT_CFG_TYPE_ECHO_REQ 0x51455245u /* "EREQ" in ASCII (see 'net_tcp.h Note #1c3'). */ #define NET_TCP_OPT_CFG_TYPE_ECHO_REPLY 0x4F484345u /* "ECHO" in ASCII (see 'net_tcp.h Note #1c3'). */ #define NET_TCP_OPT_CFG_TYPE_TS 0x20205354u /* "TS " in ASCII (see 'net_tcp.h Note #1c4'). */ #elif (CPU_CFG_DATA_SIZE == CPU_WORD_SIZE_16) #define NET_TCP_OPT_CFG_TYPE_NONE 0x4F4E454Eu /* "NONE" in ASCII. */ #define NET_TCP_OPT_CFG_TYPE_MAX_SEG_SIZE 0x534D2053u /* "MSS " in ASCII. */ #define NET_TCP_OPT_CFG_TYPE_WIN_SCALE 0x4957204Eu /* "WIN " in ASCII (see 'net_tcp.h Note #1c1'). */ #define NET_TCP_OPT_CFG_TYPE_SACK_PERMIT 0x4353504Bu /* "SCKP" in ASCII (see 'net_tcp.h Note #1c2'). */ #define NET_TCP_OPT_CFG_TYPE_SACK 0x41534B43u /* "SACK" in ASCII (see 'net_tcp.h Note #1c2'). */ #define NET_TCP_OPT_CFG_TYPE_ECHO_REQ 0x52455145u /* "EREQ" in ASCII (see 'net_tcp.h Note #1c3'). */ #define NET_TCP_OPT_CFG_TYPE_ECHO_REPLY 0x43454F48u /* "ECHO" in ASCII (see 'net_tcp.h Note #1c3'). */ #define NET_TCP_OPT_CFG_TYPE_TS 0x53542020u /* "TS " in ASCII (see 'net_tcp.h Note #1c4'). */ #else /* Dflt CPU_WORD_SIZE_08. */ #define NET_TCP_OPT_CFG_TYPE_NONE 0x4E4F4E45u /* "NONE" in ASCII. */ #define NET_TCP_OPT_CFG_TYPE_MAX_SEG_SIZE 0x4D535320u /* "MSS " in ASCII. */ #define NET_TCP_OPT_CFG_TYPE_WIN_SCALE 0x57494E20u /* "WIN " in ASCII (see 'net_tcp.h Note #1c1'). */ #define NET_TCP_OPT_CFG_TYPE_SACK_PERMIT 0x53434B50u /* "SCKP" in ASCII (see 'net_tcp.h Note #1c2'). */ #define NET_TCP_OPT_CFG_TYPE_SACK 0x5341434Bu /* "SACK" in ASCII (see 'net_tcp.h Note #1c2'). */ #define NET_TCP_OPT_CFG_TYPE_ECHO_REQ 0x45524551u /* "EREQ" in ASCII (see 'net_tcp.h Note #1c3'). */ #define NET_TCP_OPT_CFG_TYPE_ECHO_REPLY 0x4543484Fu /* "ECHO" in ASCII (see 'net_tcp.h Note #1c3'). */ #define NET_TCP_OPT_CFG_TYPE_TS 0x54532020u /* "TS " in ASCII (see 'net_tcp.h Note #1c4'). */ #endif #endif /*$PAGE*/ /* ********************************************************************************************************* * TCP CONNECTION TIMEOUT DEFINES * * Note(s) : (1) (a) (1) RFC #1122, Section 4.2.2.13 'DISCUSSION' states that "the graceful close algorithm * of TCP requires that the connection state remain defined on (at least) one end of * the connection, for a timeout period of 2xMSL ... During this period, the (remote * socket, local socket) pair that defines the connection is busy and cannot be reused". * * (2) The following sections reiterate that the TIME-WAIT state timeout scalar is two * maximum segment lifetimes (2 MSL) : * * (A) RFC #793, Section 3.9 'Event Processing : SEGMENT ARRIVES : * Check Sequence Number : TIME-WAIT STATE' * (B) RFC #793, Section 3.9 'Event Processing : SEGMENT ARRIVES : * Check FIN Bit : TIME-WAIT STATE' * * (b) (1) RFC #793, Section 3.3 'Sequence Numbers : Knowing When to Keep Quiet' states that * "the Maximum Segment Lifetime (MSL) is ... to be 2 minutes. This is an engineering * choice, and may be changed if experience indicates it is desirable to do so". * * (2) Microsoft Corporation's Windows XP defaults MSL to 15 seconds. ********************************************************************************************************* */ /* Max seg timeout (see Note #1b) : */ #define NET_TCP_CONN_TIMEOUT_MAX_SEG_MIN_SEC ( 0u ) /* ... min = 0 seconds */ #define NET_TCP_CONN_TIMEOUT_MAX_SEG_MAX_SEC ( 2u * DEF_TIME_NBR_SEC_PER_MIN) /* ... max = 2 minutes */ #define NET_TCP_CONN_TIMEOUT_MAX_SEG_DFLT_SEC ( 15u ) /* ... dflt = 15 seconds */ #define NET_TCP_CONN_TIMEOUT_MAX_SEG_SCALAR 2u /* ... scalar (see Note #1a). */ #define NET_TCP_CONN_TIMEOUT_CONN_DFLT_SEC (120u * DEF_TIME_NBR_SEC_PER_MIN) /* Dflt conn timeout = 120 minutes */ #define NET_TCP_CONN_TIMEOUT_USER_DFLT_SEC ( 30u * DEF_TIME_NBR_SEC_PER_MIN) /* Dflt user timeout = 30 minutes */ /*$PAGE*/ /* ********************************************************************************************************* * TCP CONNECTION STATES * * Note(s) : (1) See the following RFC's for TCP state machine summary : * * (a) RFC # 793; Sections 3.2, 3.4, 3.5, 3.9 * (b) RFC #1122; Sections 4.2.2.8, 4.2.2.10, 4.2.2.11, 4.2.2.13, 4.2.2.18, 4.2.2.20 * * (2) (a) #### Additional closing-data-available state used for closing connections to allow the * application layer to receive any remaining data. * * See also 'net_tcp.c NetTCP_RxPktConnHandlerFinWait1() Note #2f5A2', * 'net_tcp.c NetTCP_RxPktConnHandlerFinWait2() Note #2f5B', * 'net_tcp.c NetTCP_RxPktConnHandlerClosing() Note #2d2B2a1B', * & 'net_tcp.c NetTCP_RxPktConnHandlerLastAck() Note #2d2A1b'. ********************************************************************************************************* */ #define NET_TCP_CONN_STATE_NONE 0u #define NET_TCP_CONN_STATE_FREE 1u #define NET_TCP_CONN_STATE_CLOSED 10u #define NET_TCP_CONN_STATE_LISTEN 20u #define NET_TCP_CONN_STATE_SYNC_RXD 30u #define NET_TCP_CONN_STATE_SYNC_RXD_PASSIVE 31u #define NET_TCP_CONN_STATE_SYNC_RXD_ACTIVE 32u #define NET_TCP_CONN_STATE_SYNC_TXD 35u #define NET_TCP_CONN_STATE_CONN 40u #define NET_TCP_CONN_STATE_FIN_WAIT_1 50u #define NET_TCP_CONN_STATE_FIN_WAIT_2 51u #define NET_TCP_CONN_STATE_CLOSING 52u #define NET_TCP_CONN_STATE_TIME_WAIT 53u #define NET_TCP_CONN_STATE_CLOSE_WAIT 55u #define NET_TCP_CONN_STATE_LAST_ACK 56u #define NET_TCP_CONN_STATE_CLOSING_DATA_AVAIL 59u /* See Note #2a. */ /* ********************************************************************************************************* * TCP CONNECTION QUEUE STATES ********************************************************************************************************* */ #define NET_TCP_RX_Q_STATE_NONE 0u #define NET_TCP_RX_Q_STATE_CLOSED 100u #define NET_TCP_RX_Q_STATE_CLOSING 101u #define NET_TCP_RX_Q_STATE_SYNC 110u #define NET_TCP_RX_Q_STATE_CONN 111u #define NET_TCP_TX_Q_STATE_NONE 0u #define NET_TCP_TX_Q_STATE_CLOSED 200u #define NET_TCP_TX_Q_STATE_CLOSING 201u #define NET_TCP_TX_Q_STATE_SYNC 210u #define NET_TCP_TX_Q_STATE_CONN 211u #define NET_TCP_TX_Q_STATE_SUSPEND 215u #define NET_TCP_TX_Q_STATE_CLOSED_SUSPEND 220u #define NET_TCP_TX_Q_STATE_CLOSING_SUSPEND 221u /*$PAGE*/ /* ********************************************************************************************************* * TCP CONNECTION CODE DEFINES **************
上传时间： 2015-11-22
上传用户：the same kong
This book is an entry-level text on the technology of telecommunications. It has been crafted with the newcomer in mind. The twenty-one chapters of text have been prepared for high-school graduates who understand algebra, logarithms, and the basic principles of electricity such as Ohm’s law. However, it is appreciated that many readers require support in these areas. Appendices A and B review the essentials of electricity and mathematics up through logarithms. This material was placed in the appendices so as not to distract from the main theme, the technology of telecommunication systems. Another topic that many in the industry find difficult is the use of decibels and derived units. Appendix C provides the reader a basic understanding of decibels and their applications. The only mathematics necessary is an understanding of the powers of ten
标签： Telecommunications Fundamentals 2nd of ed
上传时间： 2020-05-27
上传用户：shancjb
