为了改进产品性能和兼容性，最新的HDMI compliance test specification (HDMI CTS) V.1.3增加了新的测试内容和定下了更严格的标准。大多数现在递交给HDMI授权测试中心(ATC) 的带有HDMI功能的电器都将按照HDMI CTS V.1.3 来测试。Analog Devices (ADI) 分别在美国的绿堡(Greensboro，NC), 东京, 台湾和北京设立了四家预测试中心为客户提供HDMI CT 测试以缩短客户产品上市的时间。在本文中我们将讨论HDMI CTS V.1.3新增加的一些重要内容。同时我们也将着重总结一些典型测试项目失败的原因和可能的修改方案。
上传时间： 2013-12-15
上传用户：古谷仁美
This application note discusses a variety of approaches for interfacing analog signals to 5V powered systems. Synthesizing a "rail-to-rail" op amp and scaling techniques for A/D converters are covered. A voltage-to-frequency converter, applicable where high resolution is required, is also presented.
上传时间： 2013-10-12
上传用户：181992417
pic mcu code:This application note describes the design and implementation of a USB Mass Storage Device (MSD) using a Secure Digital card, which should prove useful to developers of USB mass storage solutions. This application may be used as a stand-alone MSD or as a Secure Digital/Multimedia Card (SD/MMC) reader/ writer interface.
标签： implementation application describes Storage
上传时间： 2014-11-23
上传用户：天诚24
This project is created using the Keil ARM CA Compiler. The Logic Analyzer built into the simulator may be used to monitor and display any variable or peripheral I/O register. It is already configured to show the PWM output signal on PORT3.0 and PORT3.1 This ARM Example may be debugged using only the uVision Simulator and your PC--no additional hardware or evaluation boards are required. The Simulator provides cycle-accurate simulation of all on-chip peripherals of the ADuC7000 device series. You may create various input signals like digital pulses, sine waves, sawtooth waves, and square waves using signal functions which you write in C. Signal functions run in the background in the simulator within timing constraints you configure. In this example, several signal functions are defined in the included Startup_SIM.INI file.
标签： the Analyzer Compiler project
上传时间： 2013-12-19
上传用户：Yukiseop
This example demonstrates how to erase, write, and read the on-chip 640-byte EEPROM Data Memory of the Analog Devices ADuC812, ADuC814, ADuC816, and ADuC824 devivces. This example includes a µ Vision2 Project with a target for each supported device.
标签： demonstrates example on-chip EEPROM
上传时间： 2015-05-04
上传用户：wl9454
This example program shows how to configure and use the A/D Converter of the following microcontroller: STMicroelectronics ST10F166 After configuring the A/D, the program reads the A/D result and outputs the converted value using the serial port. To run this program... Build the project (Project Menu, Build Target) Start the debugger (Debug Menu, Start/Stop Debug Session) View the Serial Window (View Menu, Serial Window #1) View the A/D converter peripheral (Peripheral Menu, A/D Converter) Run the program (Debug Menu, Go) A debug script (debug.ini) creates buttons that set different analog values in A/D channels. As the program runs, you will see the A/D input and output change. Other buttons create signals that generate sine wave or sawtooth patterns as analog inputs. µ Vision3 users may enable the built-in Logic Analyzer to view, measure and compare these input signals graphically.
标签： microcontroll Converter configure following
上传时间： 2014-12-01
上传用户：独孤求源
The project KEIL_IODemo shows how to use memory allocation routines (malloc) and char I/O (printf, scanf) via a serial interface with the Keil ARM toolchain. The I/O functions are adapted for the Analog Devices ADuC7000 series using the SERIAL.C module. The example also shows the efficiency of the Keil CA ARM Compiler run-time library which is tuned for single chip systems.
标签： KEIL_IODemo allocation routines project
上传时间： 2013-12-08
上传用户：ve3344
UART I/O and Memory Allocation Example for GNU The project GNU_IODemo shows how to use memory allocation routines (malloc) and char I/O (printf, scanf) via a serial interface with the GNU toolchain. The I/O functions are adapted for the Analog Devices ADuC7000 series using the SERIAL.C module. The example also shows the efficiency of the Keil CA ARM Compiler run-time library which is tuned for single chip systems.
标签： Allocation GNU_IODemo Example project
上传时间： 2015-05-04
上传用户：Amygdala
常用MATLAP程序，包括通信DSP常用算法。希望对大家用帮助 matlap example,including communivation digital signal process.
上传时间： 2015-06-18
上传用户：coeus
dvbsnoop is a DVB/MPEG stream analyzer program. The program can be used to sniff, monitor, debug, dump or view DVB/MPEG/DSM-CC/MHP stream information (digital television or data broadcasts) sent via satellite, cable or terrestrial.
标签： program dvbsnoop analyzer monitor
上传时间： 2013-12-14
上传用户：zhangyi99104144
