车载太阳能充电器。
上传时间： 2013-10-16
上传用户：cherrytree6
MSP430x09x 是TI 推出的业界首款名符其实的 0.9V 微控制器 (MCU)，它的出现让便携式设备中真正使用单电池供电成为可能，将推动单节电池供电的、更小巧、更低成本的便携式产品的发展。与现有号称0.9V 技术的MCU 不同，MSP430x09x 能够以0.9V 的低电压运行所有模拟和数字逻辑，因此该系列MCU 无需板载升压转换器，从而可为整体系统降低功耗，减少了对外部电路的需求。同时，在降低工作电压的情况下，仍继承了MSP430 系列单片机原有的优秀特性和丰富外设，并开创性的设计了功能丰富的模拟功能模块—模拟功能池（A-Pool）。本文将介绍MSP430x09x 系列MCU 在电动剃须刀系统中的应用，并着重阐述该系统的软硬件设计
上传时间： 2013-12-19
上传用户：hanbeidang
汽车转向灯程序及pr0tues
上传时间： 2013-10-27
上传用户：432234
电动智能小车（完整论文）
上传时间： 2013-10-11
上传用户：15071087253
电动智能小车(完整论文),绝对值得一看
上传时间： 2013-10-23
上传用户：372825274
单片机控制汽车语音技术
上传时间： 2014-11-03
上传用户：ouyang426
基于STC89C52单片机的全自动充电机设计
上传时间： 2014-12-26
上传用户：李彦东
为了有效地提升铅酸蓄电池的使用寿命，同时实现对充电过程的监控，设计出一种用单片机控制的36 V铅酸蓄电池充电电源。本电路采用反激式拓扑，连续电流工作模式，电源管理IC设计在电源的副边，由ELAN公司的EM78P258N单片机模拟，是用可编程器件模拟电源管理IC，实现智能电源低成本化的一次成功尝试，通过对单片机的软件设计实现了充电电源的状态显示、充电时间控制、报警、过温保护、过压保护、过流保护等功能。本充电器真正的实现了铅酸蓄电池的三段式充电过程，其最高输出功率可达90 W，效率约85%，成本不到20元，具有很高的市场竞争力。 Abstract: In order to extend the life of lead-acid battery efficiently and supervise the charging process meanwhile， a 36V lead-acid battery charge powe supply controlled by microcontroller is designed. The charger is flyback switching power supply and works in CCM mode. A EM78P258N microcontroller made by ELAN microelectronics corporation is used as power management IC which is designed at the secondary circuit. The project is a successful attempt to low-cost intelligent power used microcontroller simulating power management IC. The charger also has the functions of the status reveal， charge time control， alarming， thermal protect， current limit and overvoltage protect by the software design. The circuit actually implements the three-step charge process， whose power is up to 90W and whose efficiency can get 85%. The net cost of this charger is less than 20 RMB， so that the charger is of powerful market competitiveness.
上传时间： 2013-11-16
上传用户：cepsypeng
以C8051F020为核心处理器，设计无线传感器网络数据采集系统。系统采用SZ05-ADV型无线通讯模块组建Zigbee无线网络，结合嵌入式系统的软硬件技术，完成终端节点的8路传感器信号的数据采集。现场8路信号通过前端处理后，分别送入C8051F020的12位A/D转换器进行转换。经过精确处理、存储后的现场数据，通过Zigbee无线网络传送到上位机，系统可达到汽车试验中无线测试的目的。 Abstract: This paper designs a wireless sensor network system for data acquisition with C8051F020 as core processors.The system used SZ05-ADV wireless communication module，set up a Zigbee wireless network， combined with hardware and software technologies of embedded systems，completed the end-node 8-locale sensor signal data acquisition.Eight locale signals were sent separately into the 12-bit ADC of C8051F020 for conversion through front treatment.After accurate processing and storage，the locale data was transmitted to the host computer through Zigbee wireless.The system achieves the purpose of wireless testing in vehicle trial.
标签： C8051F020 Zigbee 汽车测试 系统设计
上传时间： 2013-11-23
上传用户：dsgkjgkjg
首先研究CAN总线和SAE J1939协议，提出一种基于MC9S12HZ256微控制器的总线式汽车数字仪表解决方案。详细介绍SAE J1939协议的报文帧格式及应用层协议中发动机相关参数的定义，以及步进电机及其驱动和车速信号的处理方法。该数字仪表系统硬件平台由微处理器和信号采集和信息处理及显示等模块组成。软件设计部分编程实现了对CAN总线和各传感器数据的读取、处理。该系统能够实时反映车辆工况。 Abstract: In this paper，CAN bus and SAE J1939protocol are researched，and a vehicle digital instrument solution based on MC9S12HZ256MCU is proposed.The message frame format and some engine-related parameters’definition in SAE J1939application layer protocol are introduced in detail.Stepper motor and its driver，the methods of speed signal process-ing are also introduced.The hardware platform of vehicle digital instrument is composed by MCU，signal acquisition mod-ule，and signal processing and displaying module.Data receiving and processing from CAN bus and sensors are accom-plished by programming，and vehicle condition can be reflected in real-time.
上传时间： 2013-10-20
上传用户：huannan88
