sdr_sdram.csf

Altera 官方提供的SDRAM控制器,verilog的

AUTO_INSERT_ELA_ENTITY(bc_ela)
{
	ELA_ENTITY_NAME = bc_ela;
	AUTO_INSERT_ELA_ENTITY = DISABLE;
	SOURCE_FILE = bc_ela.tdf;
}
DEFAULT_DEVICE_OPTIONS
{
	RESERVE_PIN = "AS INPUT TRI-STATED";
	RESERVED_ALL_UNUSED_PINS = "AS OUTPUT DRIVING GROUND";
	HEXOUT_FILE_COUNT_DIRECTION = UP;
	HEXOUT_FILE_START_ADDRESS = 0;
	GENERATE_HEX_FILE = OFF;
	GENERATE_RBF_FILE = OFF;
	GENERATE_TTF_FILE = OFF;
	RESERVE_DATA7_THROUGH_DATA1_AFTER_CONFIGURATION = OFF;
	RESERVE_RDYNBUSY_AFTER_CONFIGURATION = OFF;
	RESERVE_NWS_NRS_NCS_CS_AFTER_CONFIGURATION = OFF;
	DISABLE_CONF_DONE_AND_NSTATUS_PULLUPS_ON_CONFIG_DEVICE = OFF;
	AUTO_INCREMENT_CONFIG_DEVICE_JTAG_USER_CODE = ON;
	CONFIG_DEVICE_JTAG_USER_CODE = FFFFFFFF;
	CONFIGURATION_DEVICE = EPC2LC20;
	USE_CONFIGURATION_DEVICE = ON;
	ENABLE_INIT_DONE_OUTPUT = OFF;
	ENABLE_LOCK_OUTPUT = OFF;
	ENABLE_DEVICE_WIDE_OE = OFF;
	ENABLE_DEVICE_WIDE_RESET = OFF;
	RELEASE_CLEARS_BEFORE_TRI_STATES = OFF;
	AUTO_RESTART_CONFIGURATION = ON;
	USER_START_UP_CLOCK = OFF;
	CONFIGURATION_SCHEME = "PASSIVE SERIAL";
	JTAG_USER_CODE = FFFFFFFF;
}
CHIP(sdr_sdram)
{
	|DQM[0] : LOCATION = Pin_H4;
	|DQM[1] : LOCATION = Pin_H6;
	|DQM[2] : LOCATION = Pin_C7;
	|DQM[3] : LOCATION = Pin_G10;
	|DQ[0] : LOCATION = Pin_H7;
	|DQ[10] : LOCATION = Pin_F3;
	|DQ[11] : LOCATION = Pin_E4;
	|DQ[12] : LOCATION = Pin_F4;
	|DQ[13] : LOCATION = Pin_F5;
	|DQ[14] : LOCATION = Pin_E3;
	|DQ[15] : LOCATION = Pin_E5;
	|DQ[16] : LOCATION = Pin_F6;
	|DQ[17] : LOCATION = Pin_A4;
	|DQ[18] : LOCATION = Pin_B4;
	|DQ[19] : LOCATION = Pin_A5;
	|DQ[1] : LOCATION = Pin_G7;
	|DQ[20] : LOCATION = Pin_B5;
	|DQ[21] : LOCATION = Pin_C6;
	|DQ[22] : LOCATION = Pin_C5;
	|DQ[23] : LOCATION = Pin_E6;
	|DQ[24] : LOCATION = Pin_F7;
	|DQ[25] : LOCATION = Pin_A7;
	|DQ[26] : LOCATION = Pin_G9;
	|DQ[27] : LOCATION = Pin_D6;
	|DQ[28] : LOCATION = Pin_D7;
	|DQ[29] : LOCATION = Pin_J11;
	|DQ[2] : LOCATION = Pin_H5;
	|DQ[30] : LOCATION = Pin_B7;
	|DQ[31] : LOCATION = Pin_H10;
	|DQ[3] : LOCATION = Pin_G6;
	|DQ[4] : LOCATION = Pin_C4;
	|DQ[5] : LOCATION = Pin_G4;
	|DQ[6] : LOCATION = Pin_G8;
	|DQ[7] : LOCATION = Pin_G3;
	|DQ[8] : LOCATION = Pin_G5;
	|DQ[9] : LOCATION = Pin_D5;
	"|sdr_data_path:data_path1" : LOCATION = MegaLAB_Col_1;
	RESERVED_ALL_UNUSED_PINS = "AS OUTPUT DRIVING GROUND";
	HEXOUT_FILE_COUNT_DIRECTION = UP;
	HEXOUT_FILE_START_ADDRESS = 0;
	GENERATE_HEX_FILE = OFF;
	GENERATE_RBF_FILE = OFF;
	GENERATE_TTF_FILE = OFF;
	RESERVE_DATA7_THROUGH_DATA1_AFTER_CONFIGURATION = OFF;
	RESERVE_RDYNBUSY_AFTER_CONFIGURATION = OFF;
	RESERVE_NWS_NRS_NCS_CS_AFTER_CONFIGURATION = OFF;
	DISABLE_CONF_DONE_AND_NSTATUS_PULLUPS_ON_CONFIG_DEVICE = OFF;
	AUTO_INCREMENT_CONFIG_DEVICE_JTAG_USER_CODE = ON;
	CONFIG_DEVICE_JTAG_USER_CODE = FFFFFFFF;
	CONFIGURATION_DEVICE = EPC2LC20;
	USE_CONFIGURATION_DEVICE = ON;
	ENABLE_INIT_DONE_OUTPUT = OFF;
	ENABLE_LOCK_OUTPUT = OFF;
	ENABLE_DEVICE_WIDE_OE = OFF;
	ENABLE_DEVICE_WIDE_RESET = OFF;
	RELEASE_CLEARS_BEFORE_TRI_STATES = OFF;
	AUTO_RESTART_CONFIGURATION = ON;
	USER_START_UP_CLOCK = OFF;
	CONFIGURATION_SCHEME = "PASSIVE SERIAL";
	JTAG_USER_CODE = FFFFFFFF;
	BASE_PIN_OUT_FILE_ON_SAMEFRAME_DEVICE = OFF;
	DEVICE = "EP20K400EFC672-1X";
}
COMPILER_SETTINGS
{
	FOCUS_ENTITY_NAME = |sdr_sdram;
	RUN_TIMING_ANALYSES = ON;
	COMPILATION_LEVEL = FULL;
	SAVE_DISK_SPACE = ON;
	SPEED_DISK_USAGE_TRADEOFF = NORMAL;
	OPTIMIZE_IO_TIMING = ON;
	OPTIMIZE_INTERNAL_TIMING = "EXTRA EFFORT";
	FAMILY = APEX20KE;
}