📄 i2c_master_bit_ctrl.v
字号:
//
/////////////////////////////////////
// Bit controller section
/////////////////////////////////////
//
// Translate simple commands into SCL/SDA transitions
// Each command has 5 states, A/B/C/D/idle
//
// start: SCL ~~~~~~~~~~\____
// SDA ~~~~~~~~\______
// x | A | B | C | D | i
//
// repstart SCL ____/~~~~\___
// SDA __/~~~\______
// x | A | B | C | D | i
//
// stop SCL ____/~~~~~~~~
// SDA ==\____/~~~~~
// x | A | B | C | D | i
//
//- write SCL ____/~~~~\____
// SDA ==X=========X=
// x | A | B | C | D | i
//
//- read SCL ____/~~~~\____
// SDA XXXX=====XXXX
// x | A | B | C | D | i
//
// Timing: Normal mode Fast mode
///////////////////////////////////////////////////////////////////////
// Fscl 100KHz 400KHz
// Th_scl 4.0us 0.6us High period of SCL
// Tl_scl 4.7us 1.3us Low period of SCL
// Tsu:sta 4.7us 0.6us setup time for a repeated start condition
// Tsu:sto 4.0us 0.6us setup time for a stop conditon
// Tbuf 4.7us 1.3us Bus free time between a stop and start condition
//
// synopsys translate_off
`include "timescale.v"
// synopsys translate_on
`include "i2c_master_defines.v"
module i2c_master_bit_ctrl(
clk, rst, nReset,
clk_cnt, ena, cmd, cmd_ack, busy, al, din, dout,
scl_i, scl_o, scl_oen, sda_i, sda_o, sda_oen
);
//
// inputs & outputs
//
input clk;
input rst;
input nReset;
input ena; // core enable signal
input [15:0] clk_cnt; // clock prescale value
input [3:0] cmd;
output cmd_ack; // command complete acknowledge
reg cmd_ack;
output busy; // i2c bus busy
reg busy;
output al; // i2c bus arbitration lost
reg al;
input din;
output dout;
reg dout;
// I2C lines
input scl_i; // i2c clock line input
output scl_o; // i2c clock line output
output scl_oen; // i2c clock line output enable (active low)
reg scl_oen;
input sda_i; // i2c data line input
output sda_o; // i2c data line output
output sda_oen; // i2c data line output enable (active low)
reg sda_oen;
//
// variable declarations
//
reg sSCL, sSDA; // synchronized SCL and SDA inputs
reg dscl_oen; // delayed scl_oen
reg sda_chk; // check SDA output (Multi-master arbitration)
reg clk_en; // clock generation signals
wire slave_wait;
// reg [15:0] cnt = clk_cnt; // clock divider counter (simulation)
reg [15:0] cnt; // clock divider counter (synthesis)
//
// module body
//
// whenever the slave is not ready it can delay the cycle by pulling SCL low
// delay scl_oen
always @(posedge clk)
dscl_oen <= #1 scl_oen;
assign slave_wait = dscl_oen && !sSCL;
// generate clk enable signal
always @(posedge clk or negedge nReset)
if(~nReset)
begin
cnt <= #1 16'h0;
clk_en <= #1 1'b1;
end
else if (rst)
begin
cnt <= #1 16'h0;
clk_en <= #1 1'b1;
end
else if ( ~|cnt || ~ena)
if (~slave_wait)
begin
cnt <= #1 clk_cnt;
clk_en <= #1 1'b1;
end
else
begin
cnt <= #1 cnt;
clk_en <= #1 1'b0;
end
else
begin
cnt <= #1 cnt - 16'h1;
clk_en <= #1 1'b0;
end
// generate bus status controller
reg dSCL, dSDA;
reg sta_condition;
reg sto_condition;
// synchronize SCL and SDA inputs
// reduce metastability risc
always @(posedge clk or negedge nReset)
if (~nReset)
begin
sSCL <= #1 1'b1;
sSDA <= #1 1'b1;
dSCL <= #1 1'b1;
dSDA <= #1 1'b1;
end
else if (rst)
begin
sSCL <= #1 1'b1;
sSDA <= #1 1'b1;
dSCL <= #1 1'b1;
dSDA <= #1 1'b1;
end
else
begin
sSCL <= #1 scl_i;
sSDA <= #1 sda_i;
dSCL <= #1 sSCL;
dSDA <= #1 sSDA;
end
// detect start condition => detect falling edge on SDA while SCL is high
// detect stop condition => detect rising edge on SDA while SCL is high
always @(posedge clk or negedge nReset)
if (~nReset)
begin
sta_condition <= #1 1'b0;
sto_condition <= #1 1'b0;
end
else if (rst)
begin
sta_condition <= #1 1'b0;
sto_condition <= #1 1'b0;
end
else
begin
sta_condition <= #1 ~sSDA & dSDA & sSCL;
sto_condition <= #1 sSDA & ~dSDA & sSCL;
end
// generate i2c bus busy signal
always @(posedge clk or negedge nReset)
if(!nReset)
busy <= #1 1'b0;
else if (rst)
busy <= #1 1'b0;
else
busy <= #1 (sta_condition | busy) & ~sto_condition;
// generate arbitration lost signal
// aribitration lost when:
// 1) master drives SDA high, but the i2c bus is low
// 2) stop detected while not requested
reg cmd_stop, dcmd_stop;
always @(posedge clk or negedge nReset)
if (~nReset)
begin
cmd_stop <= #1 1'b0;
dcmd_stop <= #1 1'b0;
al <= #1 1'b0;
end
else if (rst)
begin
cmd_stop <= #1 1'b0;
dcmd_stop <= #1 1'b0;
al <= #1 1'b0;
end
else
begin
cmd_stop <= #1 cmd == `I2C_CMD_STOP;
dcmd_stop <= #1 cmd_stop;
al <= #1 (sda_chk & ~sSDA & sda_oen) | (sto_condition & ~dcmd_stop);
end
// generate dout signal (store SDA on rising edge of SCL)
always @(posedge clk)
if(sSCL & ~dSCL)
dout <= #1 sSDA;
// generate statemachine
// nxt_state decoder
parameter [16:0] idle = 17'b0_0000_0000_0000_0000;
parameter [16:0] start_a = 17'b0_0000_0000_0000_0001;
parameter [16:0] start_b = 17'b0_0000_0000_0000_0010;
parameter [16:0] start_c = 17'b0_0000_0000_0000_0100;
parameter [16:0] start_d = 17'b0_0000_0000_0000_1000;
parameter [16:0] start_e = 17'b0_0000_0000_0001_0000;
parameter [16:0] stop_a = 17'b0_0000_0000_0010_0000;
parameter [16:0] stop_b = 17'b0_0000_0000_0100_0000;
parameter [16:0] stop_c = 17'b0_0000_0000_1000_0000;
parameter [16:0] stop_d = 17'b0_0000_0001_0000_0000;
parameter [16:0] rd_a = 17'b0_0000_0010_0000_0000;
parameter [16:0] rd_b = 17'b0_0000_0100_0000_0000;
parameter [16:0] rd_c = 17'b0_0000_1000_0000_0000;
parameter [16:0] rd_d = 17'b0_0001_0000_0000_0000;
parameter [16:0] wr_a = 17'b0_0010_0000_0000_0000;
parameter [16:0] wr_b = 17'b0_0100_0000_0000_0000;
parameter [16:0] wr_c = 17'b0_1000_0000_0000_0000;
parameter [16:0] wr_d = 17'b1_0000_0000_0000_0000;
reg [16:0] c_state; // synopsis enum_state
always @(posedge clk or negedge nReset)
if (!nReset)
begin
c_state <= #1 idle;
cmd_ack <= #1 1'b0;
scl_oen <= #1 1'b1;
sda_oen <= #1 1'b1;
sda_chk <= #1 1'b0;
end
else if (rst | al)
begin
c_state <= #1 idle;
cmd_ack <= #1 1'b0;
scl_oen <= #1 1'b1;
sda_oen <= #1 1'b1;
sda_chk <= #1 1'b0;
end
else
begin
cmd_ack <= #1 1'b0; // default no command acknowledge + assert cmd_ack only 1clk cycle
if (clk_en)
case (c_state) // synopsis full_case parallel_case
// idle state
idle:
begin
case (cmd) // synopsis full_case parallel_case
`I2C_CMD_START:
c_state <= #1 start_a;
`I2C_CMD_STOP:
c_state <= #1 stop_a;
`I2C_CMD_WRITE:
c_state <= #1 wr_a;
`I2C_CMD_READ:
c_state <= #1 rd_a;
default:
c_state <= #1 idle;
endcase
scl_oen <= #1 scl_oen; // keep SCL in same state
sda_oen <= #1 sda_oen; // keep SDA in same state
sda_chk <= #1 1'b0; // don't check SDA output
end
// start
start_a:
begin
c_state <= #1 start_b;
scl_oen <= #1 scl_oen; // keep SCL in same state
sda_oen <= #1 1'b1; // set SDA high
sda_chk <= #1 1'b0; // don't check SDA output
end
start_b:
begin
c_state <= #1 start_c;
scl_oen <= #1 1'b1; // set SCL high
sda_oen <= #1 1'b1; // keep SDA high
sda_chk <= #1 1'b0; // don't check SDA output
end
start_c:
begin
c_state <= #1 start_d;
scl_oen <= #1 1'b1; // keep SCL high
sda_oen <= #1 1'b0; // set SDA low
sda_chk <= #1 1'b0; // don't check SDA output
end
start_d:
begin
c_state <= #1 start_e;
scl_oen <= #1 1'b1; // keep SCL high
sda_oen <= #1 1'b0; // keep SDA low
sda_chk <= #1 1'b0; // don't check SDA output
end
start_e:
begin
c_state <= #1 idle;
cmd_ack <= #1 1'b1;
scl_oen <= #1 1'b0; // set SCL low
sda_oen <= #1 1'b0; // keep SDA low
sda_chk <= #1 1'b0; // don't check SDA output
end
// stop
stop_a:
begin
c_state <= #1 stop_b;
scl_oen <= #1 1'b0; // keep SCL low
sda_oen <= #1 1'b0; // set SDA low
sda_chk <= #1 1'b0; // don't check SDA output
end
stop_b:
begin
c_state <= #1 stop_c;
scl_oen <= #1 1'b1; // set SCL high
sda_oen <= #1 1'b0; // keep SDA low
sda_chk <= #1 1'b0; // don't check SDA output
end
stop_c:
begin
c_state <= #1 stop_d;
scl_oen <= #1 1'b1; // keep SCL high
sda_oen <= #1 1'b0; // keep SDA low
sda_chk <= #1 1'b0; // don't check SDA output
end
stop_d:
begin
c_state <= #1 idle;
cmd_ack <= #1 1'b1;
scl_oen <= #1 1'b1; // keep SCL high
sda_oen <= #1 1'b1; // set SDA high
sda_chk <= #1 1'b0; // don't check SDA output
end
// read
rd_a:
begin
c_state <= #1 rd_b;
scl_oen <= #1 1'b0; // keep SCL low
sda_oen <= #1 1'b1; // tri-state SDA
sda_chk <= #1 1'b0; // don't check SDA output
end
rd_b:
begin
c_state <= #1 rd_c;
scl_oen <= #1 1'b1; // set SCL high
sda_oen <= #1 1'b1; // keep SDA tri-stated
sda_chk <= #1 1'b0; // don't check SDA output
end
rd_c:
begin
c_state <= #1 rd_d;
scl_oen <= #1 1'b1; // keep SCL high
sda_oen <= #1 1'b1; // keep SDA tri-stated
sda_chk <= #1 1'b0; // don't check SDA output
end
rd_d:
begin
c_state <= #1 idle;
cmd_ack <= #1 1'b1;
scl_oen <= #1 1'b0; // set SCL low
sda_oen <= #1 1'b1; // keep SDA tri-stated
sda_chk <= #1 1'b0; // don't check SDA output
end
// write
wr_a:
begin
c_state <= #1 wr_b;
scl_oen <= #1 1'b0; // keep SCL low
sda_oen <= #1 din; // set SDA
sda_chk <= #1 1'b0; // don't check SDA output (SCL low)
end
wr_b:
begin
c_state <= #1 wr_c;
scl_oen <= #1 1'b1; // set SCL high
sda_oen <= #1 din; // keep SDA
sda_chk <= #1 1'b1; // check SDA output
end
wr_c:
begin
c_state <= #1 wr_d;
scl_oen <= #1 1'b1; // keep SCL high
sda_oen <= #1 din;
sda_chk <= #1 1'b1; // check SDA output
end
wr_d:
begin
c_state <= #1 idle;
cmd_ack <= #1 1'b1;
scl_oen <= #1 1'b0; // set SCL low
sda_oen <= #1 din;
sda_chk <= #1 1'b0; // don't check SDA output (SCL low)
end
endcase
end
// assign scl and sda output (always gnd)
assign scl_o = 1'b0;
assign sda_o = 1'b0;
endmodule
⌨️ 快捷键说明
复制代码
Ctrl + C
搜索代码
Ctrl + F
全屏模式
F11
切换主题
Ctrl + Shift + D
显示快捷键
?
增大字号
Ctrl + =
减小字号
Ctrl + -