📄 unicntr.pin
字号:
-- Copyright (C) 1991-2005 Altera Corporation
-- Your use of Altera Corporation's design tools, logic functions
-- and other software and tools, and its AMPP partner logic
-- functions, and any output files any of the foregoing
-- (including device programming or simulation files), and any
-- associated documentation or information are expressly subject
-- to the terms and conditions of the Altera Program License
-- Subscription Agreement, Altera MegaCore Function License
-- Agreement, or other applicable license agreement, including,
-- without limitation, that your use is for the sole purpose of
-- programming logic devices manufactured by Altera and sold by
-- Altera or its authorized distributors. Please refer to the
-- applicable agreement for further details.
--
-- This is a Quartus II output file. It is for reporting purposes only, and is
-- not intended for use as a Quartus II input file. This file cannot be used
-- to make Quartus II pin assignments - for instructions on how to make pin
-- assignments, please see Quartus II help.
---------------------------------------------------------------------------------
---------------------------------------------------------------------------------
-- NC : No Connect. This pin has no internal connection to the device.
-- VCC : Dedicated power pin, which MUST be connected to VCC.
-- VCCIO : Dedicated power pin, which MUST be connected to VCC
-- of its bank.
-- GND : Dedicated ground pin. Dedicated GND pins MUST be connected to GND.
-- It can also be used to report unused dedicated pins. The connection
-- on the board for unused dedicated pins depends on whether this will
-- be used in a future design. One example is device migration. When
-- using device migration, refer to the device pin-tables. If it is a
-- GND pin in the pin table or if it will not be used in a future design
-- for another purpose the it MUST be connected to GND. If it is an unused
-- dedicated pin, then it can be connected to a valid signal on the board
-- (low, high, or toggling) if that signal is required for a different
-- revision of the design.
-- GND+ : Unused input pin. It can also be used to report unused dual-purpose pins.
-- This pin should be connected to GND. It may also be connected to a
-- valid signal on the board (low, high, or toggling) if that signal
-- is required for a different revision of the design.
-- GND* : Unused I/O pin. This pin can either be left unconnected or
-- connected to GND. Connecting this pin to GND will improve the
-- device's immunity to noise.
-- RESERVED : Unused I/O pin, which MUST be left unconnected.
-- RESERVED_INPUT : Pin is tri-stated and should be connected to the board.
-- NON_MIGRATABLE: This pin cannot be migrated.
---------------------------------------------------------------------------------
Quartus II Version 5.0 Build 148 04/26/2005 SJ Web Edition
CHIP "unicntr" ASSIGNED TO AN: EPM7032SLC44-5
Pin Name/Usage : Location : Dir. : I/O Standard : Voltage : I/O Bank : User Assignment
-------------------------------------------------------------------------------------------------------------
GND+ : 1 : : : : :
GND+ : 2 : : : : :
VCC : 3 : power : : : :
RESERVED : 4 : : : : :
dataout[1] : 5 : output : TTL : : : N
dataout[0] : 6 : output : TTL : : : N
TDI : 7 : input : TTL : : : N
dataout[2] : 8 : output : TTL : : : N
datain[0] : 9 : input : TTL : : : N
GND : 10 : gnd : : : :
dataout[3] : 11 : output : TTL : : : N
termcnt : 12 : output : TTL : : : N
TMS : 13 : input : TTL : : : N
dataout[4] : 14 : output : TTL : : : N
VCC : 15 : power : : : :
datain[1] : 16 : input : TTL : : : N
dataout[5] : 17 : output : TTL : : : N
datain[3] : 18 : input : TTL : : : N
dataout[6] : 19 : output : TTL : : : N
datain[5] : 20 : input : TTL : : : N
dataout[7] : 21 : output : TTL : : : N
GND : 22 : gnd : : : :
VCC : 23 : power : : : :
datain[6] : 24 : input : TTL : : : N
datain[4] : 25 : input : TTL : : : N
serinr : 26 : input : TTL : : : N
serinl : 27 : input : TTL : : : N
RESERVED : 28 : : : : :
datain[2] : 29 : input : TTL : : : N
GND : 30 : gnd : : : :
RESERVED : 31 : : : : :
TCK : 32 : input : TTL : : : N
RESERVED : 33 : : : : :
RESERVED : 34 : : : : :
VCC : 35 : power : : : :
mode[2] : 36 : input : TTL : : : N
RESERVED : 37 : : : : :
TDO : 38 : output : TTL : : : N
mode[1] : 39 : input : TTL : : : N
mode[0] : 40 : input : TTL : : : N
RESERVED : 41 : : : : :
GND : 42 : gnd : : : :
clock : 43 : input : TTL : : : N
datain[7] : 44 : input : TTL : : : N
⌨️ 快捷键说明
复制代码
Ctrl + C
搜索代码
Ctrl + F
全屏模式
F11
切换主题
Ctrl + Shift + D
显示快捷键
?
增大字号
Ctrl + =
减小字号
Ctrl + -