Abstract: Transimpedance amplifiers (TIAs) are widely used to translate the current output of sensors like photodiode-to-voltagesignals, since several circuits and instruments can only accept voltage input. An operational amplifier with a feedback resistor fromoutput to the inverting input is the most straightforward implementation of such a TIA. However, even this simple TIA circuit requirescareful trade-offs among noise gain, offset voltage, bandwidth, and stability. Clearly stability in a TIA is essential for good, reliableperformance. This application note explains the empirical calculations for assessing stability and then shows how to fine-tune theselection of the feedback phase-compensation capacitor.
标签： Transimpedance Stabilize Amplifier youR
上传时间： 2013-11-13
上传用户：daoyue
Abstract: Using a wafer-level package (WLP) can reduce the overall size and cost of youR solution.However when using a WLP IC, the printed circuit board (PCB) layout can become more complex and, ifnot carefully planned, result in an unreliable design. This article presents some PCB designconsiderations and general recommendations for choosing a 0.4mm- or 0.5mm-pitch WLP for youRapplication.
标签： Considerations Guidelines and Design
上传时间： 2013-10-14
上传用户：ysystc699
Abstract: How smart is youR LED lighting system? While LED lighting holds the promise of reducingenergy consumption and maintenance costs, smart LED lighting designs improve system performance in
上传时间： 2013-11-15
上传用户：13162218709
Removing output capacitors saves money and boardspace. Linear Technology’s OPTI-LOOPTM architectureallows you to use the output capacitors of youR choice andcompensate the control loop for optimum transientresponse and loop stability. Figure 1 shows the dramaticimprovement possible with the OPTI-LOOP architecture.With the improvement shown in Figure 1, less capacitance
上传时间： 2013-12-15
上传用户：fanboynet
This white paper raises some fundamental issues the design engineer should address before deciding upon a communication approach for a wireless network. As no universal wireless network solution exists, it should be custom tailored to suit the application demands. Defining youR application communication characteristics is the key to ensure optimal communication reliability and resistance to interfering noise sources.
上传时间： 2013-11-23
上传用户：zhichenglu
Safety GuidelinesThis manual contains notices which you should observe to ensure youR own personal safety, as well as toprotect the product and connected equipment. These notices are highlighted in the manual by a warningtriangle and are marked as follows according to the level of danger:
标签： Programmable 300 and
上传时间： 2013-12-12
上传用户：fandeshun
Important Notice SUNPLUS INNOVATION TECHNOLOGY INC. reserves the right to change this documentation without prior notice. Information provided by SUNPLUS INNOVATION TECHNOLOGY INC. is believed to be accurate and reliable. However, SUNPLUS INNOVATION TECHNOLOGY INC.makes no warranty for any errors which may appear in this document. Contact SUNPLUS INNOVATION TECHNOLOGY INC.to obtain the latest version of device specifications before placing youR order. No responsibility is assumed by SUNPLUS INNOVATION TECHNOLOGY INC. for any infringement of patent or other rights of third parties which may result from its use. In addition, SUNPLUSIT products are not authorized for use as critical components in life support systems or aviation systems, where a malfunction or failure of the product may reasonably be expected to result in significant injury to the user, without the express written approval of SunplusIT
标签： SUNPLUSIT Q-Writer 编程工具 使用说明书
上传时间： 2013-10-13
上传用户：brain kung
The MSP-FET430U14 is a powerful flash emulation tool to quickly begin application development on the MSP430 MCU. It includes USB debugging interface used to program and debug the MSP430 in-system through the JTAG interface or the pin saving Spy Bi-Wire (2-wire JTAG) protocol. The flash memory can be erased and programmed in seconds with only a few keystrokes, and since the MSP430 flash is ultra-low power, no external power supply is required. The debugging tool interfaces the MSP430 to the included integrated software environment and includes code to start youR design immediately. The MSP-FET430UIF development tools supports development with all MSP430 flash devices
上传时间： 2013-10-28
上传用户：13691535575
This application note shows how to write an Inter Integrated Circuit bus driver (I²C) for the Philips P90CL301micro-controller.It is not only an example of writing a driver, but it also includes a set of application interface software routines toquickly implement a complete I²C multi-master system application.For specific applications the user will have to make minimal changes in the driver program. Using the drivermeans linking modules to youR application software and including a header-file into the application sourceprograms. A small example program of how to use the driver is listed.The driver supports i.a. polled or interrupt driven message handling, slave message transfers and multi-mastersystem applications. Furthermore, it is made suitable for use in conjunction with real time operating systems, likepSOS+.
上传时间： 2013-11-23
上传用户：weixiao99
The PL2303 USB to Serial adapter is youR smart and convenient accessory forconnecting RS-232 serial devices to youR USB-equipped Windows host computer. Itprovides a bridge connection with a standard DB 9-pin male serial port connector inone end and a standard Type-A USB plug connector on the other end. You simplyattach the serial device onto the serial port of the cable and plug the USB connectorinto youR PC USB port. It allows a simple and easy way of adding serial connectionsto youR PC without having to go thru inserting a serial card and traditional portconfiguration.This USB to Serial adapter is ideal for connecting modems, cellular phones, PDAs,digital cameras, card readers and other serial devices to youR computer. It providesserial connections up to 1Mbps of data transfer rate. And since USB does not requireany IRQ resource, more devices can be attached to the system without the previoushassles of device and resource conflicts.Finally, the PL-2303 USB to Serial adapter is a fully USB Specification compliantdevice and therefore supports advanced power management such as suspend andresume operations as well as remote wakeup. The PL-2303 USB Serial cable adapteris designed to work on all Windows operating systems.
上传时间： 2013-11-01
上传用户：ghostparker
