设计了一种用于高速ADC中的高速高增益的全差分CMOS运算放大器。主运放采用带开关电容共模反馈的折叠式共源共栅结构，利用增益提高和三支路电流基准技术实现一个可用于12~14 bit精度，100 MS/s采样频率的高速流水线（Pipelined）ADC的运放。设计基于SMIC 0.25 μm CMOS工艺，在Cadence环境下对电路进行Spectre仿真。仿真结果表明，在2.5 V单电源电压下驱动2 pF负载时，运放的直流增益可达到124 dB，单位增益带宽720 MHz，转换速率高达885 V/μs，达到0.1%的稳定精度的建立时间只需4 ns，共模抑制比153 dB。
上传时间： 2014-12-23
上传用户：jiiszha
数字水印作为一种防护技术，在数字产品的保护认证方面越发显得重要，成为当前计算机领域研究的热点问题之一。提出了一种在空域采用分块重复嵌入水印信息和HVS相结合的水印技术。实验结果说明，分块技术在空域的使用提高了水印的嵌入强度和降低计算复杂度，该算法在抵抗旋转、裁剪、缩放方面等有较强能力；水印算法与HVS技术的有效性相结合，数字水印具有很好的掩蔽性。
上传时间： 2013-10-23
上传用户：qwerasdf
This paper presents a space vector modulation(SVM)-based switching strategy for a three-level neutral point clamped (NPC) converter that is adapted as a STATCOM.
上传时间： 2013-10-20
上传用户：zyt
Who has never experienced oscillations issues when using an operational amplifier? Opampsare often used in a simple voltage follower configuration. However, this is not the bestconfiguration in terms of capacitive loading and potential risk of oscillations.Capacitive loads have a big impact on the stability of operational amplifier-basedapplications. Several compensation methods exist to stabilize a standard op-amp. Thisapplication note describes the most common ones, which can be used in most cases.The general theory of each compensation method is explained, and based on this, specific
上传时间： 2013-10-28
上传用户：chenbhdt
Control systems are becoming increasingly dependent on digital processing and so require sensors able to provide direct digital inputs. Sensors based on time measurement, having outputs based on a frequency or phase, have an advantage over conventional analogue sensors in that their outputs can be measured directly in digital systems by pulse counting.
上传时间： 2013-10-08
上传用户：wuyuying
A complete design for a data acquisition card for the IBM PC is detailed in this application note. Additionally, C language code is provided to allow sampling of data at speed of more than 20kHz. The speed limitation is strictly based on the execution speed of the "C" data acquisition loop. A "Turbo" XT can acquire data at speeds greater than 20kHz. Machines with 80286 and 80386 processors can go faster than 20kHz. The computer that was used as a test bed in this application was an XT running at 4.77MHz and therefore all system timing and acquisition time measurements are based on a 4.77MHz clock speed.
上传时间： 2013-10-29
上传用户：BOBOniu
Low power operation of electronic apparatus has becomeincreasingly desirable. Medical, remote data acquisition,power monitoring and other applications are good candidatesfor battery driven, low power operation. Micropoweranalog circuits for transducer-based signal conditioningpresent a special class of problems. Although micropowerICs are available, the interconnection of these devices toform a functioning micropower circuit requires care. (SeeBox Sections, “Some Guidelines for Micropower Designand an Example” and “Parasitic Effects of Test Equipmenton Micropower Circuits.”) In particular, trade-offs betweensignal levels and power dissipation become painful whenperformance in the 10-bit to 12-bit area is desirable.
上传时间： 2013-10-22
上传用户：rocketrevenge
通过安装和调试ＥＣＧ放大器，了解医学信号放大器的特点，并掌握放大器的有关指标。 安装和调试后的ＥＣＧ放大器，应达到以下指标： １?具有较高输入阻抗＞１ＭΩ ２?放大器差动增益约为１０００ ３?具有较高共模抑制比（CMRR>80db） ４?等效输入噪声＜１０μＶ ５?频带范围０.０５Ｈｚ～１００Ｈｚ
上传时间： 2013-10-18
上传用户：taiyang250072
本文阐述电视机、显示器和微机等产品的谐波电流产生原因，介绍抑制谐波电流的方法及设计时应考虑的问题。 关键词：谐波电流、抑制技术
标签： 谐波电流抑制
上传时间： 2013-11-01
上传用户：a673761058
2-1 何谓测量放大电路？对其基本要求是什么？ 在测量控制系统中，用来放大传感器输出的微弱电压，电流或电荷信号的放大电路称为测量放大电路，亦称仪用放大电路。对其基本要求是：①输入阻抗应与传感器输出阻抗相匹配；②一定的放大倍数和稳定的增益；③低噪声；④低的输入失调电压和输入失调电流以及低的漂移；⑤足够的带宽和转换速率（无畸变的放大瞬态信号）；⑥高输入共模范围（如达几百伏）和高共模抑制比；⑦可调的闭环增益；⑧线性好、精度高；⑨成本低。 2-2 图2-2a所示斩波稳零放大电路中，为什么采用高、低频两个通道，即R3、C3组成的高频通道和调制、解调、交流放大器组成的低频通道？ 采用高频通道是为了使斩波稳零放大电路能在较宽的频率范围内工作，而采用低频通道则能对微弱的直流或缓慢变化的信号进行低漂移和高精度的放大。 2-3 请参照图2-3，根据手册中LF347和CD4066的连接图（即引脚图），将集成运算放大器LF347和集成模拟开关CD4066接成自动调零放大电路。 LF347和CD4066接成的自动调零放大电路如图X2-1。
标签： 信号放大电路
上传时间： 2013-10-09
上传用户：ysjing
