This application note is intended for system designers who require a hardware implementation overview of the development board features such as the power supply, the clock management, the reset control, the boot mode settings and the debug management. It shows how to use the High-density and Medium-density STM32F10xxx product families and describes the minimum hardware resources required to develop an STM32F10xxx application.
上传时间： 2013-04-24
上传用户：epson850
Abstract: This application note describes how to design boost converters using the MAX17597 peakcurrent-mode controller. Boost converters can be operated in discontinuous conduction mode (DCM) orcontinuous conduction mode (CCM). This operating mode can affect the component choices, stress levelin power devices, and controller design. Formulas for calculating component values and ratingsare alsopresented.
上传时间： 2013-11-16
上传用户：zcs023047
交流功率因数转换器 特点： 精确度0.25%满刻度 ±0.25o 多种输入,输出选择 输入与输出绝缘耐压2仟伏特/1分钟 冲击电压测试5仟伏特(1.2x50us) (IEC255-4,ANSI C37.90a/1974) 突波电压测试2.5仟伏特(0.25ms/1MHz) (IEC255-4) 尺寸小，稳定性高 主要规格： 精确度: 0.25% F.S. ±0.25°(23 ±5℃) 输入负载: <0.2VA (Voltage) <0.2VA (Current) 最大过载能力: Current related input: 3 x rated continuous 10 x rated 30 sec. 25 x rated 3sec. 50 x rated 1sec. Voltage related input:maximum 2 x rated continuous 输出反应速度: < 250ms(0~90%) 输出负载能力: < 10mA for voltage mode < 10V for current mode 输出之涟波: < 0.1% F.S. 归零调整范围: 0~ ±5% F.S. 最大值调整范围: 0~ ±10% F.S. 温度系数: 100ppm/℃ (0~50℃) 隔离特性: Input/Output/Power/Case 绝缘抗阻: >100Mohm with 500V DC 绝缘耐压能力: 2KVac/1 min. (input/output/power/case) 突波测试: ANSI C37.90a/1974,DIN-IEC 255-4 impulse voltage 5KV(1.2x50us) 使用环境条件: -20~60℃(20 to 90% RH non-condensed) 存放环境条件: -30~70℃(20 to 90% RH non-condensed) CE认证: EN 55022:1998/A1:2000 Class A EN 61000-3-2:2000 EN 61000-3-3:1995/A1:2001 EN 55024:1998/A1:2001
上传时间： 2013-10-22
上传用户：thing20
交流频率转换器 特点： 精确度0.05%满刻度(Accuracy 0.05%F.S.) 多种输入,输出选择 输入与输出绝缘耐压2仟伏特/1分钟 冲击电压测试5仟伏特(1.2x50us) (IEC255-4,ANSI C37.90a/1974) 突波电压测试2.5仟伏特(0.25ms/1MHz) (IEC255-4) 尺寸小，稳定性高 2:主要规格 精确度: 0.05% F.S. (23 ±5℃) 输入负载: <0.2VA 最大过载能力:maximum 2 x rated continuous 输出反应时间: <250ms (0~90%) 输出负载能力: <10mA for voltage mode <10V for current mode 输出涟波: <0.1% F.S. 归零调整范围: 0~±5% F.S. 最大值调整范围: 0~±10% F.S. 温度系数: 50ppm/℃ (0~50℃) 隔离特性: Input/Output/Power/Case 绝缘抗阻: >100M ohm with 500V DC 绝缘耐压能力: 2KVac/1 min. (input/output/power) 行动测试: ANSI C37.90a/1974,DIN-IEC 255-4 impulse voltage 5KV (1.2 x 50us) 突波测试: 2.5KV-0.25ms/1MHz 使用环境条件: -20~60℃(20 to 90% RH non-condensed) 存放环境条件: -30~70℃(20 to 90% RH non-condensed) CE认证: EN 55022:1998/A1:2000 Class A EN 61000-3-2:2000 EN 61000-3-3:1995/A1:2001 EN 55024:1998/A1:2001
上传时间： 2013-10-11
上传用户：xzt
交流电压，电流转换器 特点： 精确度0.25%满刻度(RMS) 多种输入,输出选择 输入与输出绝缘耐压2仟伏特/1分钟 冲击电压测试5仟伏特(1.2x50us) (IEC255-4,ANSI C37.90a/1974) 突波电压测试2.5仟伏特(0.25ms/1MHz) (IEC255-4) 尺寸小，稳定性高 2:主要规格 精确度:0.25%F.S.(RMS) (23 ±5℃) 输入负载: <0.2VA(voltage) <0.2VA(current) 最大过载能力: Current related input:3 x rated continuous 10 x rated 30 sec. ,25 x rated 3sec. 50 x rated 1sec. Voltage related input:maximum 2x rated continuous 输出反应时间: <250ms (0~90%) 输出负载能力: <10mA for voltage mode <10V for current mode 输出涟波: <0.1% F.S. 归零调整范围: 0~±5% F.S. 最大值调整范围: 0~±10% F.S. 温度系数: 100ppm/℃ (0~50℃) 隔离特性: Input/Output/Power/Case 绝缘抗阻: >100Mohm with 500V DC 绝缘耐压能力: 2KVac/1 min. (input/output/power) 行动测试: ANSI C37.90a/1974,DIN-IEC 255-4 impulse voltage 5KV (1.2 x 50us) 突波测试: 2.5KV-0.25ms/1MHz 使用环境条件: -20~60℃(20 to 90% RH non-condensed) 存放环境条件: -30~70℃(20 to 90% RH non-condensed) CE认证: EN 55022:1998/A1:2000 Class A EN 61000-3-2:2000 EN 61000-3-3:1995/A1:2001 EN 55024:1998/A1:2001
上传时间： 2013-11-09
上传用户：非衣2016
Abstract: Alexander Graham Bell patented twisted pair wires in 1881. We still use them today because they work so well. In addition we have the advantage ofincredible computer power within our world. Circuit simulators and filter design programs are available for little or no cost. We combine the twisted pair and lowpassfilters to produce spectacular rejection of radio frequency interference (RFI) and electromagnetic interference (EMI). We also illustrate use of a precision resistorarray to produce a customizable differential amplifier. The precision resistors set the gain and common mode rejection ratios, while we choose the frequencyresponse.
上传时间： 2014-11-26
上传用户：Vici
采用电流模脉宽调制控制方案的电池充电芯片设计,锯齿波信号的线性度较好,当负载电路减小时,自动进入Burst Mode状态提高系统的效率。整个电路基于1.0 μm 40 V CMOS工艺设计,通过Hspice完成了整体电路前仿真验证和后仿真,仿真结果表明,振荡电路的性能较好,可广泛应用在PWM等各种电子电路中。
上传时间： 2014-12-23
上传用户：kangqiaoyibie
A fully differential amplifi er is often used to converta single-ended signal to a differential signal, a designwhich requires three signifi cant considerations: theimpedance of the single-ended source must match thesingle-ended impedance of the differential amplifi er,the amplifi er’s inputs must remain within the commonmode voltage limits and the input signal must be levelshifted to a signal that is centered at the desired outputcommon mode voltage.
上传时间： 2013-11-09
上传用户：wweqas
ANALOG INPUT BANDWIDTH is a measure of the frequencyat which the reconstructed output fundamental drops3 dB below its low frequency value for a full scale input. Thetest is performed with fIN equal to 100 kHz plus integer multiplesof fCLK. The input frequency at which the output is −3dB relative to the low frequency input signal is the full powerbandwidth.APERTURE JITTER is the variation in aperture delay fromsample to sample. Aperture jitter shows up as input noise.APERTURE DELAY See Sampling Delay.BOTTOM OFFSET is the difference between the input voltagethat just causes the output code to transition to the firstcode and the negative reference voltage. Bottom Offset isdefined as EOB = VZT–VRB, where VZT is the first code transitioninput voltage and VRB is the lower reference voltage.Note that this is different from the normal Zero Scale Error.CONVERSION LATENCY See PIPELINE DELAY.CONVERSION TIME is the time required for a completemeasurement by an analog-to-digital converter. Since theConversion Time does not include acquisition time, multiplexerset up time, or other elements of a complete conversioncycle, the conversion time may be less than theThroughput Time.DC COMMON-MODE ERROR is a specification which appliesto ADCs with differential inputs. It is the change in theoutput code that occurs when the analog voltages on the twoinputs are changed by an equal amount. It is usually expressed in LSBs.
上传时间： 2013-11-12
上传用户：pans0ul
模拟集成电路的设计与其说是一门技术，还不如说是一门艺术。它比数字集成电路设计需要更严格的分析和更丰富的直觉。严谨坚实的理论无疑是严格分析能力的基石，而设计者的实践经验无疑是诞生丰富直觉的源泉。这也正足初学者对学习模拟集成电路设计感到困惑并难以驾驭的根本原因。.美国加州大学洛杉机分校(UCLA)Razavi教授凭借着他在美国多所著名大学执教多年的丰富教学经验和在世界知名顶级公司(AT&T，Bell Lab，HP)卓著的研究经历为我们提供了这本优秀的教材。本书自2000午出版以来得到了国内外读者的好评和青睐，被许多国际知名大学选为教科书。同时，由于原著者在世界知名顶级公司的丰富研究经历，使本书也非常适合作为CMOS模拟集成电路设计或相关领域的研究人员和工程技术人员的参考书。... 本书介绍模拟CMOS集成电路的分析与设计。从直观和严密的角度阐述了各种模拟电路的基本原理和概念，同时还阐述了在SOC中模拟电路设计遇到的新问题及电路技术的新发展。本书由浅入深，理论与实际结合，提供了大量现代工业中的设计实例。全书共18章。前10章介绍各种基本模块和运放及其频率响应和噪声。第11章至第13章介绍带隙基准、开关电容电路以及电路的非线性和失配的影响，第14、15章介绍振荡器和锁相环。第16章至18章介绍MOS器件的高阶效应及其模型、CMOS制造工艺和混合信号电路的版图与封装。 1 Introduction to Analog Design 2 Basic MOS Device Physics 3 Single-Stage Amplifiers 4 Differential Amplifiers 5 Passive and Active Current Mirrors 6 Frequency Response of Amplifiers 7 Noise 8 Feedback 9 Operational Amplifiers 10 Stability and Frequency Compensation 11 Bandgap References 12 Introduction to Switched-Capacitor Circuits 13 Nonlinearity and Mismatch 14 Oscillators 15 Phase-Locked Loops 16 Short-Channel Effects and Device Models 17 CMOS Processing Technology 18 Layout and Packaging
上传时间： 2014-12-23
上传用户：杜莹12345
