针对飞行模拟器座舱数据采集的复杂性，设计了一种基于以太网分布式的数据采集控制系统，该系统是RCM5700微处理器模块上的以太网应用。在系统的基础上具体讨论了PoE技术的应用，在传输数据的网线上同时提供电流，提出并实现了一种包括辅助电源在内的完整可靠的PoE供电方案。设计采用美国国家半导体的LM5073和LM5576并根据不同的负载情况，进行稳定可靠的电压转换，以满足数据采集电路的要求。实验结果表明：该设计稳定可靠，满足低于13 W的采集节点供电要求，提高了模拟器信号采集系统的通用性和标准化程度，避免了以往数据采集节点单独繁琐的电源设计。 Abstract: Aiming at the complexity of large avion simulation and controlling，the simulator cabin distribute data collecting and control system was designed. This system is the application of RCM5700 on Ethernet. Based on this system，PoE technique that makes Ethernet can also provide power were expounded with emphasis and included FAUX design the PoE resolution was realized. To achieve the requirement of this system，LM5073 and LM5576 were used to DC-DC switch. From the data of experiment，the design filled the requirement of power-need of node whose power was lower than 13W. The application of the technique can advance the degree of simulation data collections currency and standardization and avoid designing additional power system.
上传时间： 2013-11-09
上传用户：xyipie
针对微型四旋翼飞行器非线性动力学模型下姿态稳定和速度跟踪控制问题，基于全局快速终端滑模控制（TSMC-terminal sliding mode control）方法研究了控制器设计。通过引入等价控制输入，将姿态控制通道解耦并分别设计了姿态稳定TSMC控制器。对速度跟踪和高度跟踪控制，在保证高度跟踪控制稳定的基础上设计了保证速度跟踪的耦合控制器。姿态稳定和速度跟踪仿真验证了设计控制器的性能。
上传时间： 2013-10-23
上传用户：xcsx1945
特点 最高輸入頻率 10KHz 显示范围0-9999（一段设定）0至999999累积量 计数速度 50/10000脈波/秒可选择 输入脈波具有预设刻度功能 累积量同步（批量）或非同步（批次）计数可选择 数位化指拨设定操作简易 计数暂时停止功能 1组报警功能 2:主要規格 脈波輸入型式: Jump-pin selectable current sourcing(NPN) or current sinking (PNP) 脉波触发电位: HI bias (CMOS) (VIH=7.5V, VIL=5.5V) LO bias (TTL) (VIH=3.7V, VIL=2.0V) 最高输入频率: <10KHz (up,down,up/down mode) 输出动作时间 : 0.1 to 99.9 second adjustable 输出复归方式: Manual(N) or automatic (R or C) can be modif 继电器容量: AC 250V-5A, DC 30V-7A 显示值范围: 0-9999（PV,SV） 0-999999(TV) 显示幕: Red high efficiency LEDs high 7.0mm (.276")(PV,SV) Red high efficiency LEDs high 9.2mm (.36")(TV) 参数设定方式: Touch switches 感应器电源: 12VDC +/-3%(<60mA) 记忆方式: Non-volatile E2PROM memory 绝缘耐压能力: 2KVac/1 min. (input/output/power) 1600Vdc (input/output) 使用环境条件: 0-50℃(20 to 90% RH non-condensed) 存放环境条件: 0-70℃(20 to 90% RH non-condensed) CE认证: EN 55022:1998/A1:2000 Class A EN 61000-3-2:2000 EN 61000-3-3:1995/A1:2001 EN 55024:1998/A1:2001
上传时间： 2013-10-24
上传用户：wvbxj
特点 最高輸入頻率 10KHz 计数速度 50/10000脈波/秒可选择 四种输入模式可选择(加算,減算,加減算,90度相位差加減算) 90度相位差加減算具有提高解析度4倍功能 输入脈波具有预设刻度功能 计数暂时停止功能 3组报警功能 15BIT类比输出功能 数位RS-485界面 2:主要規格 脈波輸入型式: Jump-pin selectable current sourcing(NPN) or current sinking (PNP) 脉波触发电位: HI bias (CMOS) (VIH=7.5V, VIL=5.5V) LO bias (TTL) (VIH=3.7V, VIL=2.0V) 最高输入频率: <10KHz (up,down,up/down mode) <3KHz (quadrature mode) 输出动作时间 : 0.1 to 99.9 second adjustable 输出复归方式: Manual(N) or automatic (R or C) can be modif 继电器容量: AC 250V-5A, DC 30V-7A 显示值范围: -199999 to 999999 类比输出解析度: 15 bit DAC 输出反应速度: < 1/f+10ms(0-90%) 输出负载能力: < 10mA for voltage mode < 10V for current mode <[(V+)-7.5V]/20mA for two-wire mode 输出之涟波: < 0.1% F.S. 通讯位址: "01"-"FF" 传输速度: 19200/9600/4800/2400 selective 通信协议: Modbus RTU mode 显示幕: Red high efficiency LEDs high 14.22mm (.56") 参数设定方式: Touch switches 感应器电源: 12VDC +/-3%(<60mA) 记忆方式: Non-volatile E2PROM memory 绝缘耐压能力: 2KVac/1 min. (input/output/power) 1600Vdc (input/output) 使用环境条件: 0-50℃(20 to 90% RH non-condensed) 存放环境条件: 0-70℃(20 to 90% RH non-condensed) CE认证: EN 55022:1998/A1:2000 Class A EN 61000-3-2:2000 EN 61000-3-3:1995/A1:2001 EN 55024:1998/A1:2001
上传时间： 2013-11-23
上传用户：redmoons
特点 最高輸入頻率 10KHz 计数速度 50/10000脈波/秒可选择 四种输入模式可选择(加算,減算,加減算,90度相位差加減算) 90度相位差加減算具有提高解析度4倍功能 输入脈波具有预设刻度功能 前置量设定功能(二段設定)可选择 数位化指拨设定操作简易 计数暂时停止功能 3组报警功能 2:主要規格 脈波輸入型式: Jump-pin selectable current sourcing(NPN) or current sinking (PNP) 脉波触发电位: HI bias (CMOS) (VIH=7.5V, VIL=5.5V) LO bias (TTL) (VIH=3.7V, VIL=2.0V) 最高输入频率: <10KHz (up,down,up/down mode) <5KHz (quadrature mode) 输出动作时间 : 0.1 to 99.9 second adjustable 输出复归方式: Manual(N) or automatic (R or C) can be modif 继电器容量: AC 250V-5A, DC 30V-7A 显示值范围: -199999 to 999999 显示幕: Red high efficiency LEDs high 9.2mm (.36") 参数设定方式: Touch switches 感应器电源: 12VDC +/-3%(<60mA) ( 感應器電源 ) 记忆方式: Non-volatile E2PROM memory 绝缘耐压能力: 2KVac/1 min. (input/output/power) 1600Vdc (input/output) 使用环境条件: 0-50℃(20 to 90% RH non-condensed) 存放环境条件: 0-70℃(20 to 90% RH non-condensed) CE认证: EN 55022:1998/A1:2000 Class A EN 61000-3-2:2000 EN 61000-3-3:1995/A1:2001 EN 55024:1998/A1:2001
上传时间： 2013-11-12
上传用户：909000580
特点 精确度0.1%滿刻度 可輸入交直流電流/交直流电压/電位計/傳送器...等信号 16 BIT类比输出功能 输入与输出绝缘耐压2仟伏特/1分钟 宽范围交直流兩用電源设计 尺寸小,穩定性高 2主要規格 精确度: 0.1% F.S. (23 ±5℃) 显示值范围: 0-±19999 digit adjustable 类比输出解析度: 16 bit DAC 输出反应速度: < 250 ms (0-90%)(>10Hz) 输出负载能力: < 10mA for voltage mode < 10V for current mode 输出之涟波: < 0.1% F.S. 归零调整范围: 0- ±9999 Digit adjustable 最大值调整范围: 0- ±9999 Digit adjustable 温度系数: 50ppm/℃ (0-50℃) 显示幕: Red high efficiency LEDs high 10.16mm (0.4") 隔离特性: Input/Output/Power/Case 参数设定方式: Touch switches 记忆方式: Non-volatile E2PROM memory 绝缘抗阻: >100Mohm with 500V DC 绝缘耐压能力: 2KVac/1 min. (input/output/power) 1600Vdc (input/output) 使用环境条件: 0-60℃(20 to 90% RH non-condensed) 存放环境条件: 0-70℃(20 to 90% RH non-condensed) 安装方式: Socket/plugin type with barrier terminals CE认证: EN 55022:1998/A1:2000 Class A EN 61000-3-2:2000 EN 61000-3-3:1995/A1:2001 EN 55024:1998/A1:2001
上传时间： 2014-01-05
上传用户：eastgan
无刷电机驱动,Complementary Enhancement Mode Field Effect Transistor
上传时间： 2013-11-14
上传用户：ewtrwrtwe
This application note provides step-by-step instructions on how to recreate a Tri-Mode Ethernet(TEMAC) performance testing system using the ML405 board and MontaVista Linux 4.0. Thisapplication note shows how to set up a simple EDK Base System Builder system on the ML405Evaluation Platform and run performance tests. The network architecture for the test isdescribed. A system is built and downloaded into the FPGA. A MontaVista Linux kernel isconfigured, built, and downloaded into the ML405 Evaluation Platform. The instructions forobtaining and setting up the software used to perform the measurements, netperf, are given.
上传时间： 2013-11-11
上传用户：saharawalker
The NCV7356 is a physical layer device for a single wire data linkcapable of operating with various Carrier Sense Multiple Accesswith Collision Resolution (CSMA/CR) protocols such as the BoschController Area Network (CAN) version 2.0. This serial data linknetwork is intended for use in applications where high data rate is notrequired and a lower data rate can achieve cost reductions in both thephysical media components and in the microprocessor and/ordedicated logic devices which use the network.The network shall be able to operate in either the normal data ratemode or a high-speed data download mode for assembly line andservice data transfer operations. The high-speed mode is onlyintended to be operational when the bus is attached to an off-boardservice node. This node shall provide temporary bus electrical loadswhich facilitate higher speed operation. Such temporary loads shouldbe removed when not performing download operations.The bit rate for normal communications is typically 33 kbit/s, forhigh-speed transmissions like described above a typical bit rate of83 kbit/s is recommended. The NCV7356 features undervoltagelockout, timeout for faulty blocked input signals, output blankingtime in case of bus ringing and a very low sleep mode current.
上传时间： 2013-10-24
上传用户：s蓝莓汁
The LPC2292/2294 microcontrollers are based on a 16/32-bit ARM7TDMI-S CPU with real-time emulation and embedded trace support, together with 256 kB of embedded high-speed flash memory. A 128-bit wide memory interface and a unique accelerator architecture enable 32-bit code execution at the maximum clock rate. For critical code size applications, the alternative 16-bit Thumb mode reduces code by more than 30 pct with minimal performance penalty. With their 144-pin package, low power consumption, various 32-bit timers, 8-channel 10-bit ADC, 2/4 (LPC2294) advanced CAN channels, PWM channels and up to nine external interrupt pins these microcontrollers are particularly suitable for automotive and industrial control applications as well as medical systems and fault-tolerant maintenance buses. The number of available fast GPIOs ranges from 76 (with external memory) through 112 (single-chip). With a wide range of additional serial communications interfaces, they are also suited for communication gateways and protocol converters as well as many other general-purpose applications. Remark: Throughout the data sheet, the term LPC2292/2294 will apply to devices with and without the /00 or /01 suffix. The suffixes /00 and /01 will be used to differentiate from other devices only when necessary.
上传时间： 2014-12-30
上传用户：aysyzxzm
