acm HDOJ 1051WoodenSticks Description: There is a pile of n wooden sticks. The length and weight of each stick are known in advance. The sticks are to be processed by a woodworking machine in one by one fashion. It needs some time, called setup time, for the machine to prepare processing a stick. The setup times are associated with cleaning operations and changing tools and shapes in the machine. The setup times of the woodworking machine are given as follows: (a) The setup time for the first wooden stick is 1 minute. (b) Right after processing a stick of length l and weight w , the machine will need no setup time for a stick of length l and weight w if l<=l and w<=w . Otherwise, it will need 1 minute for setup.
标签： WoodenSticks Description length wooden
上传时间： 2014-03-08
上传用户：netwolf
The task of clustering Web sessions is to group Web sessions based on similarity and consists of maximizing the intra- group similarity while minimizing the inter-group similarity． The first and foremost question needed to be considered in clustering W b sessions is how to measure the similarity between Web sessions．However．there are many shortcomings in traditiona1 measurements．This paper introduces a new method for measuring similarities between Web pages that takes into account not only the URL but also the viewing time of the visited web page．Yhen we give a new method to measure the similarity of Web sessions using sequence alignment and the similarity of W eb page access in detail Experiments have proved that our method is valid and e币cient．
标签： sessions clustering similarity Web
上传时间： 2014-01-11
上传用户：songrui
Produce Java classes to calculate and display the root of a quadratic equation when input the coefficients a, b and c within the range of -100 to 100 by user.
标签： calculate the quadratic equation
上传时间： 2014-01-17
上传用户：aappkkee
We analyze, both analytically and numerically, the effectiveness of cloaking an infinite cylinder from observations by electromagnetic waves in three dimensions. We show that, as truncated approximations of the ideal permittivity and permeability tensors tend towards the singular ideal cloaking fields, so that the anisotropy ratio tends to infinity, the D and B fields blow up near the cloaking surface. Since the metamaterials used to implement cloaking are based on effective medium theory, the resulting large variation in D and B will pose a challenge to the suitability of the field averaged characterization of " and 碌. We also consider cloaking with and without the SHS (softand- hard surface) lining, shown in [6] to be theoretically necessary for cloaking in the cylindrical geometry. We demonstrate numerically that cloaking is significantly improved by the SHS lining, with both the far field of the scattered wave significantly reduced and the blow up of D and B prevented.
标签： effectiveness analytically numerically cloaking
上传时间： 2017-03-30
上传用户：zxc23456789
In this program, several statistical fading channel simulators using the Sum-of-Sinusoids (SoS)has been implemented.A Rayleigh fading channel impulse respose using jakes model has been generated in matlab
标签： Sum-of-Sinusoids statistical simulators program
上传时间： 2017-05-30
上传用户：ainimao
Wi-Fi pollution, or an excessive number of access points in the area, especially on the same or neighboring channel, can prevent access and interfere with the use of other access points by others, caused by overlapping channels in the 802.11g/b spectrum
标签： especially pollution excessive the
上传时间： 2017-07-29
上传用户：我们的船长
The PCA9549 provides eight bits of high speed TTL-compatible bus switching controlledby the I2C-bus. The low ON-state resistance of the switch allows connections to be madewith minimal propagation delay. Any individual A to B channel or combination of channelscan be selected via the I2C-bus, determined by the contents of the programmable Controlregister. When the I2C-bus bit is HIGH (logic 1), the switch is on and data can flow fromPort A to Port B, or vice versa. When the I2C-bus bit is LOW (logic 0), the switch is open,creating a high-impedance state between the two ports, which stops the data flow.An active LOW reset input (RESET) allows the PCA9549 to recover from a situationwhere the I2C-bus is stuck in a LOW state. Pulling the RESET pin LOW resets the I2C-busstate machine and causes all the bits to be open, as does the internal power-on resetfunction.
上传时间： 2014-11-22
上传用户：xcy122677
The Point-to-Point Protocol (PPP) for the Transmission of Multi-protocol Datagrams over Point-to-Point Links Status of this Memo This RFC specifies an IAB standards track protocol for the Internet community, and requests discussion and suggestions for improvements. Please refer to the current edition of the "IAB Official Protocol Standards" for the standardization state and status of this protocol. Distribution of this memo is unlimited.
标签： Point-to-Point Multi-protocol Transmission Datagrams
上传时间： 2014-01-22
上传用户：cazjing
This section contains a brief introduction to the C language. It is intended as a tutorial on the language, and aims at getting a reader new to C started as quickly as possible. It is certainly not intended as a substitute for any of the numerous textbooks on C. 2. write a recursive function FIB (n) to find out the nth element in theFibanocci sequence number which is 1,1,2,3,5,8,13,21,34,55,…3. write the prefix and postfix form of the following infix expressiona + b – c / d + e * f – g * h / i ^ j4. write a function to count the number of nodes in a binary tr
标签： introduction the contains intended
上传时间： 2013-12-23
上传用户：liansi
Implemented BFS, DFS and A* To compile this project, use the following command: g++ -o search main.cpp Then you can run it: ./search The input is loaded from a input file in.txt Here is the format of the input file: The first line of the input file shoud contain two chars indicate the source and destination city for breadth first and depth first algorithm. The second line of input file shoud be an integer m indicate the number of connections for the map. Following m lines describe the map, each line represents to one connection in this form: dist city1 city2, which means there is a connection between city1 and city2 with the distance dist. The following input are for A* The following line contains two chars indicate the source and destination city for A* algorithm. Then there is an integer h indicate the number of heuristic. The following h lines is in the form: city dist which means the straight-line distance from the city to B is dist.
标签： Implemented following compile command
上传时间： 2014-01-01
上传用户：lhc9102
