Abstract: This application note presents an overview of the operational characteristics of accurate I²C real-time clocks (RTCs),including the DS3231, DS3231M, and DS3232. It focuses on general application guidelines that facilitate use of device resources forpower management, I²C communication circuit configurations, and I²C characteristics relative to device power-up sequences andinitializations. Additional discussions on decoupling are provided to support developing strategies for mitigating power-supply pushingof device frequency.
上传时间： 2013-11-23
上传用户：WMC_geophy
This paper presents a space vector modulation(SVM)-based switching strategy for a three-level neutral point clamped (NPC) converter that is adapted as a STATCOM.
上传时间： 2013-10-20
上传用户：zyt
Digital convergence, in recent history, has been prevalentin the consumer equipment domain and the designengineers in this area have been struggling with a plethoraof emerging standards and protocols. What lessons can welearn from their struggle? The same dilemmas now existin in-vehicle telematics and infotainment systems but withthe added issues of extremes of temperature, safety,security, and time in market.
上传时间： 2014-12-23
上传用户：9牛10
The STM32F10xxx microcontroller family embeds up to three advanced 12-bit ADCs (depending on the device) with a conversion time down to 1 μs. A self-calibration feature is provided to enhance ADC accuracy versus environmental condition changes.
上传时间： 2014-12-23
上传用户：eastimage
Control systems are becoming increasingly dependent on digital processing and so require sensors able to provide direct digital inputs. Sensors based on time measurement, having outputs based on a frequency or phase, have an advantage over conventional analogue sensors in that their outputs can be measured directly in digital systems by pulse counting.
上传时间： 2013-10-08
上传用户：wuyuying
Most circuit designers are familiar with diode dynamiccharacteristics such as charge storage, voltage dependentcapacitance and reverse recovery time. Less commonlyacknowledged and manufacturer specifi ed is diode forwardturn-on time. This parameter describes the timerequired for a diode to turn on and clamp at its forwardvoltage drop. Historically, this extremely short time, unitsof nanoseconds, has been so small that user and vendoralike have essentially ignored it. It is rarely discussed andalmost never specifi ed. Recently, switching regulator clockrate and transition time have become faster, making diodeturn-on time a critical issue. Increased clock rates aremandated to achieve smaller magnetics size; decreasedtransition times somewhat aid overall effi ciency but areprincipally needed to minimize IC heat rise. At clock speedsbeyond about 1MHz, transition time losses are the primarysource of die heating.
上传时间： 2013-10-10
上传用户：谁偷了我的麦兜
A complete design for a data acquisition card for the IBM PC is detailed in this application note. Additionally, C language code is provided to allow sampling of data at speed of more than 20kHz. The speed limitation is strictly based on the execution speed of the "C" data acquisition loop. A "Turbo" XT can acquire data at speeds greater than 20kHz. Machines with 80286 and 80386 processors can go faster than 20kHz. The computer that was used as a test bed in this application was an XT running at 4.77MHz and therefore all system timing and acquisition time measurements are based on a 4.77MHz clock speed.
上传时间： 2013-10-29
上传用户：BOBOniu
Sensors for pressure, load, temperature, acceleration andmany other physical quantities often take the form of aWheatstone bridge. These sensors can be extremely linearand stable over time and temperature. However, mostthings in nature are only linear if you don’t bend them toomuch. In the case of a load cell, Hooke’s law states that thestrain in a material is proportional to the applied stress—as long as the stress is nowhere near the material’s yieldpoint (the “point of no return” where the material ispermanently deformed).
上传时间： 2013-11-13
上传用户：墙角有棵树
Portable, battery-powered operation of electronic apparatushas become increasingly desirable. Medical, remotedata acquisition, power monitoring and other applicationsare good candidates for battery operation. In some circumstances,due to space, power or reliability considerations,it is preferable to operate the circuitry from a single 1.5Vcell. Unfortunately, a 1.5V supply eliminates almost alllinear ICs as design candidates. In fact, the LM10 opamp-reference and the LT®1017/LT1018 comparators arethe only IC gain blocks fully specifi ed for 1.5V operation.Further complications are presented by the 600mV dropof silicon transistors and diodes. This limitation consumesa substantial portion of available supply range, makingcircuit design diffi cult. Additionally, any circuit designedfor 1.5V operation must function at end-of-life batteryvoltage, typically 1.3V. (See Box Section, “Componentsfor 1.5V Operation.”)
标签： Circuitry Operation Single 1017
上传时间： 2013-12-20
上传用户：Wwill
ANALOG INPUT BANDWIDTH is a measure of the frequencyat which the reconstructed output fundamental drops3 dB below its low frequency value for a full scale input. Thetest is performed with fIN equal to 100 kHz plus integer multiplesof fCLK. The input frequency at which the output is −3dB relative to the low frequency input signal is the full powerbandwidth.APERTURE JITTER is the variation in aperture delay fromsample to sample. Aperture jitter shows up as input noise.APERTURE DELAY See Sampling Delay.BOTTOM OFFSET is the difference between the input voltagethat just causes the output code to transition to the firstcode and the negative reference voltage. Bottom Offset isdefined as EOB = VZT–VRB, where VZT is the first code transitioninput voltage and VRB is the lower reference voltage.Note that this is different from the normal Zero Scale Error.CONVERSION LATENCY See PIPELINE DELAY.CONVERSION TIME is the time required for a completemeasurement by an analog-to-digital converter. Since theConversion Time does not include acquisition time, multiplexerset up time, or other elements of a complete conversioncycle, the conversion time may be less than theThroughput Time.DC COMMON-MODE ERROR is a specification which appliesto ADCs with differential inputs. It is the change in theoutput code that occurs when the analog voltages on the twoinputs are changed by an equal amount. It is usually expressed in LSBs.
上传时间： 2013-11-12
上传用户：pans0ul
