Abstract: This application note illustrates an intermediate 8V switching power supply for an automotive radio and infotainment system.The design withstands the complete automotive input voltage range (including cold crank and load dump conditions), assuring a stable8V supply for common subsystems such as a CD driver, LCDs, and a radio module in modern infotainment systems. To avoiddisturbance in the AM and FM bands, the switching power supply runs at a fixed frequency of 2MHz, enabling an ideal solution forradio systems.
上传时间： 2013-11-20
上传用户：feitian920
交直流转换器 AT-VA2-D-A3-DD-ADL 1．产品说明 AT系列转换器/分配器主要设计使用于一般讯号迴路中之转换与隔离；如 4~20mA、0~10V、热电偶(Type K, J, E, T)、热电阻(Rtd-Pt100Ω)、荷重元、电位计(三線式)、电阻(二線式)及交流电压/电流等讯号，机种齐全。 此款薄型设计的转换器/分配器，除了能提供两组讯号输出（输出间隔离）或24V激发电源供传送器使用外，切换式电源亦提供了安装的便利性。上方并设计了电源、输入及输出指示灯及可插拔式接线端子方便现场施工及工作状态检视。 2.产品特点 可选择带指拨开关切换，六种常规输出信号0-5V/0~10V/1~5V/2~10V/4~20mA/ 0~20mA 可自行切换。 双回路输出完全隔离，可选择不同信号。 设计了电源、输入及输出LED指示灯，方便现场工作状态检视。 规格选择表中可指定选购0.1%精度 17.55mm薄型35mm导轨安装。 依据CE国际标准规范设计。 3.技术规格 用途：信号转换及隔离 过载输入能力：电流：10×额定10秒 第二组输出：可选择 精确度: 交流: ≦±0.5% of F.S. 直流: ≦±0.2% of F.S. 输入耗损: 交流电流:≤ 0.1VA; 交流电压:≤ 0.15VA 反应时间: ≤ 250msec (10%~90% of FS) 输出波紋: ≤ ±0.1% of F.S. 满量程校正范围:≤ ±10% of F.S.，2组输出可个别调整 零点校正范围:≤ ±10% of F.S.，2组输出可个别调整 隔离:AC 2.0 KV 输出1与输出2之间 隔离抗阻：DC 500V 100MΩ 工作电源: AC 85~265V/DC 100~300V, 50/60Hz 或 AC/DC 20~56V (选购规格) 消耗功率: DC 4W, AC 6.0VA 工作溫度: 0~60 ºC 工作湿度: 20~95% RH, 无结露 温度系数: ≤ 100PPM/ ºC (0~50 ºC) 储存温度: -10~70 ºC 保护等级: IP 42 振动测试: 1~800 Hz, 3.175 g2/Hz 外观尺寸: 94.0mm x 94.0mm x 17.5mm 外壳材质: ABS防火材料，UL94V0 安装轨道: 35mm DIN導軌 (EN50022) 重量: 250g 安全规范(LVD): IEC 61010 (Installation category 3) EMC: EN 55011:2002; EN 61326:2003 EMI: EN 55011:2002; EN 61326:2003 常用规格：AT-VA2-D-A3-DD-ADL 交直流转换器，2组输出，输入交流输入0-19.99mA，输出1:4-20mA,输出2：4-20mA，工作电源AC/DC20-56V
上传时间： 2013-11-22
上传用户：nem567397
ATX是计算机的工作电源，作用是把交流220V的电源转换为计算机内部使用的直流5V，12V，24V的电源。 ATX电源的特点:与AT电源相比，ATX电源增加了“＋3.3V、＋5VSB、PS－ON ”三个输出。其中“＋3.3V”输出主要是供CPU用，而“＋5VSB”、“PS－ON”输出则体现了ATX电源的特点。ATX电源最主要的特点就是，它不采用传统的市电开关来控制电源是否工作，而是采用“＋5VSB、PS－ON”的组合来实现电源的开启和关闭，只要控制“PS－ON”信号电平的变化，就能控制电源的开启和关闭。“PS－ON”小于1V伏时开启电源，大于4.5伏时关闭电源。
上传时间： 2013-11-14
上传用户：xuanjie
Abstract: Rail splitting is creating an artificial virtual ground as a reference voltage. It is used to set the signalto match the op amp's "sweet spot." An op amp has the most linear- and distortion-free qualities at that sweetspot. Typically, the sweet spot occurs near the center between the single power rail and ground. In the case ofa number of signals, the virtual ground can control channel DC errors when multiplexing or switching thesignals.
上传时间： 2013-10-23
上传用户：wushengwu
This document presents design techniques and reference circuits that power Virtex™-4 FXRocketIO™ multi-gigabit transceivers (MGTs) operating at data rates below 3.125 Gb/s.When using multiple transceivers, it is sometimes preferred to power them from a switchingpower supply. However, switching power supplies generate noise that affects transceiver
上传时间： 2013-11-18
上传用户：huang111
Traditionally, an Electronic Circuit Breaker (ECB) comprisesa MOSFET, a MOSFET controller and a current senseresistor. The LTC®4213 does away with the sense resistorby using the RDS(ON) of the external MOSFET. The resultis a simple, small solution that offers a signifi cant lowinsertion loss advantage at low operating load voltage.The LTC4213 features two circuit breaking responses tovarying overload conditions with three selectable tripthresholds and a high side drive for an external N-channelMOSFET switch.
上传时间： 2014-03-02
上传用户：lixinxiang
Video cable driver amplifi er output stages traditionallyrequire a supply voltage of at least 6V in order to providethe required output swing. This requirement is usuallymet with 5V supplies by adding a boost regulator or asmall local negative rail, say via the popular LT®1983-3.Such additional circuitry is unnecessary in typical 1VP-Pvideo connections, such as HD component video, if thecable driver amplifi ers simply offer near rail-to-rail outputcapability when powered from 5V.
上传时间： 2013-11-16
上传用户：yanyangtian
Automotive batteries, industrial power supplies, distributedsupplies and wall transformers are all sources ofwide-ranging high voltage inputs. The easiest way to stepdown these sources is with a high voltage monolithicstep-down regulator that can directly accept a wide inputrange and produce a well-regulated output. The LT®3493accepts inputs from 3.6V to 36V and LT3481 acceptsinputs from 3.6V to 34V. Both provide excellent lineand load regulation and dynamic response. The LT3481offers a high effi ciency solution over a wide load range andkeeps the output ripple low during Burst Mode® operationwhile the LT3493 provides a tiny solution with minimalexternal components. The LT3493 operates at 750kHzand the LT3481 has adjustable frequency from 300kHzto 2.8MHz. High frequency operation enables the use ofsmall, low cost inductors and ceramic capacitors.
上传时间： 2014-12-24
上传用户：Pzj
Piezoelectric motors are used in digital cameras for autofocus,zooming and optical image stabilization. Theyare relatively small, lightweight and effi cient, but theyalso require a complicated driving scheme. Traditionally,this challenge has been met with the use ofseparatecircuits, including a step-up converter and an oversizedgeneric full-bridge drive IC. The resulting high componentcount and large board space are especially problematicin the design of cameras for ever shrinking cell phones.The LT®3572 solves these problems by combining astep-up regulator and a dual full-bridge driver in a 4mm× 4mm QFN package. Figure 1 shows a typical LT3572Piezo motor drive circuit. A step-up converter is usedto generate 30V from a low voltage power source suchas a Li-Ion battery or any input power source within thepart’s wide input voltage range of 2.7V to 10V. The highoutput voltage of the step-up converter, adjustable upto 40V, is available for the drivers at the VOUT pin. Thedrivers operate in a full-bridge fashion, where the OUTAand OUTB pins are the same polarity as the PWMA andPWMB pins, respectively, and the OUTA and OUTB pinsare inverted from PWMA and PWMB, respectively. Thestep-up converter and both Piezo drivers have their ownshutdown control. Figure 2 shows a typical layout
上传时间： 2013-11-18
上传用户：hulee
The LTC®3610 is a high power monolithic synchronousstep-down DC/DC regulator that can deliver up to 12Aof continuous output current from a 4V to 24V (28Vmaximum) input supply. It is a member of a high currentmonolithic regulator family (see Table 1) that featuresintegrated low RDS(ON) N-channel top and bottomMOSFETs. This results in a high effi ciency and highpower density solution with few external components.This regulator family uses a constant on-time valleycurrent mode architecture that is capable of operatingat very low duty cycles at high frequency and with veryfast transient response. All are available in low profi le(0.9mm max) QFN packages.
上传时间： 2013-11-07
上传用户：moerwang
