本论文设计了一种基于FPGA的高速FIR数字滤波器,滤波器实现低通滤波,截止频率为1MHz,通带波纹小于1 dB,阻带最大衰减为-40 dB,输入输出数据为8位二进制,采样频率为10MHz。 论文首先简要介绍了数字滤波器的基本原理和线性FIR数字滤波器的性质、结构,根据滤波器的性能要求选择窗函数、确定系数,在算法上为了满足数字滤波器的要求,对系数放大512倍并取整,并用Matlab对数字滤波器原理进行了证明。同时简述了EDA技术和FPGA设计流程。 其次,论文说明了FIR数字滤波器模块的划分,并用Verilog语言在Modelsim环境下进行了功能测试。对于数字滤波器系数中的-1,-2,4这些简单的系数乘法直接进行移位和取反,可以极大的节省资源和优化设计。而对普通系数乘法采用4-BANT(4bits-at-a-time)的并行算法,用加法累加快速实现了乘积的运算；另外,在本设计进行部分积累加时,采用舍取冗余位,主要是根据设计时已对系数进行了放大,而输出时又要将结果相应的缩小,所以在累加时,提前对部分积缩小,从而减少了运算量,从时间和资源上都得到了优化。 论文的最后分别用Modelsim和Quartus II进行了FIR数字滤波器的前仿真和后仿真,将仿真的结果和Matlab中原理验证时得到的理想值进行了比较,并对所产生的误差进行了分析。仿真结果表明：本16阶FIR数字滤波器设计能够实现截止频率为1MHz的低通滤波,并且工作频率可达150MHz以上。
上传时间： 2013-07-15
上传用户：lanwei
华为的MG323 TCP/IP 常用AT命令
上传时间： 2013-04-24
上传用户：jacking
适用于64位系统的AT单片机下载软件，avr fighter 很适用，已调试！！！
上传时间： 2013-04-24
上传用户：f1364628965
电脑硬件更新换代快，而主机电源更新较慢，十几年的发展，就是由AT结构变化为ATX电源。
上传时间： 2013-05-18
上传用户：小小小熊
M AT L A B是一个可视化的计算程序，被广泛地使用于从个人计算机到超级计算机范围内 的各种计算机上。 M AT L A B包括命令控制、可编程，有上百个预先定义好的命令和函数。这些函数能通过 用户自定义函数进一步扩展。 M AT L A B有许多强有力的命令。例如， M AT L A B能够用一个单一的命令求解线性系统， 能完成大量的高级矩阵处理。 M AT L A B有强有力的二维、三维图形工具。 M AT L A B能与其他程序一起使用。例如， M AT L A B的图形功能，可以在一个 F O RT R A N 程序中完成可视化计
上传时间： 2013-04-24
上传用户：xinshou123456
This document was developed under the Standard Hardware and Reliability Program (SHARP) TechnologyIndependent Representation of Electronic Products (TIREP) project. It is intended for use by VHSIC HardwareDescription Language (VHDL) design engineers and is offered as guidance for the development of VHDL modelswhich are compliant with the VHDL Data Item Description (DID DI-EGDS-80811) and which can be providedto manufacturing engineering personnel for the development of production data and the subsequent productionof hardware. Most VHDL modeling performed to date has been concentrated at either the component level orat the conceptual system level. The assembly and sub-assembly levels have been largely disregarded. Under theSHARP TIREP project, an attempt has been made to help close this gap. The TIREP models are based upon lowcomplexity Standard Electronic Modules (SEM) of the format A configuration. Although these modules are quitesimple, it is felt that the lessons learned offer guidance which can readily be applied to a wide range of assemblytypes and complexities.
上传时间： 2014-12-23
上传用户：xinhaoshan2016
电位计讯号转换器 AT-PM1-P1-DN-ADL 1．产品说明 AT系列转换器/分配器主要设计使用于一般讯号迴路中之转换与隔离；如 4~20mA、0~10V、热电偶(Type K, J, E, T)、热电阻(Rtd-Pt100Ω)、荷重元、电位计(三線式)、电阻(二線式)及交流电压/电流等讯号，机种齐全。 此款薄型设计的转换器/分配器，除了能提供两组讯号输出（输出间隔离）或24V激发电源供传送器使用外，切换式电源亦提供了安装的便利性。上方并设计了电源、输入及输出指示灯及可插拔式接线端子方便现场施工及工作状态检视。 2.产品特点 可选择带指拨开关切换，六种常规输出信号0-5V/0~10V/1~5V/2~10V/4~20mA/ 0~20mA 可自行切换。 双回路输出完全隔离，可选择不同信号。 设计了电源、输入及输出LED指示灯，方便现场工作状态检视。 规格选择表中可指定选购0.1%精度 17.55mm薄型35mm导轨安装。 依据CE国际标准规范设计。 3.技术规格 用途：信号转换及隔离 过载输入能力：电流：10×额定10秒 第二组输出：可选择 输入范围：P1：0 Ω ~ 50.0 Ω / ~ 2.0 KΩ P2：0 Ω ~ 2.0 KΩ / ~ 100.0 KΩ 精确度: ≦±0.2% of F.S. ≦±0.1% of F.S. 侦测电压：1.6V 输入耗损: 交流电流:≤ 0.1VA; 交流电压:≤ 0.15VA 反应时间: ≤ 250msec (10%~90% of FS) 输出波紋: ≤ ±0.1% of F.S. 满量程校正范围:≤ ±10% of F.S.，2组输出可个别调整 零点校正范围:≤ ±10% of F.S.，2组输出可个别调整 隔离:AC 2.0 KV 输出1与输出2之间 隔离抗阻：DC 500V 100MΩ 工作电源: AC 85~265V/DC 100~300V, 50/60Hz 或 AC/DC 20~56V (选购规格) 消耗功率: DC 4W, AC 6.0VA 工作溫度: 0~60 ºC 工作湿度: 20~95% RH, 无结露 温度系数: ≤ 100PPM/ ºC (0~50 ºC) 储存温度: -10~70 ºC 保护等级: IP 42 振动测试: 1~800 Hz, 3.175 g2/Hz 外观尺寸: 94.0mm x 94.0mm x 17.5mm 外壳材质: ABS防火材料，UL94V0 安装轨道: 35mm DIN導軌 (EN50022) 重量: 250g 安全规范(LVD): IEC 61010 (Installation category 3) EMC: EN 55011:2002; EN 61326:2003 EMI: EN 55011:2002; EN 61326:2003 常用规格：AT-PM1-P1-DN-ADL 电位计讯号转换器，一组输出，输入范围：0 Ω ~ 50.0 Ω / ~ 2.0 KΩ，输出一组输出4-20mA，工作电源AC/DC20-56V
上传时间： 2013-11-05
上传用户：feitian920
The LT®6552 is a specialized dual-differencing 75MHzoperational amplifier ideal for rejecting common modenoise as a video line receiver. The input pairs are designedto operate with equal but opposite large-signal differencesand provide exceptional high frequency commonmode rejection (CMRR of 65dB at 10MHz), therebyforming an extremely versatile gain block structure thatminimizes component count in most situations. The dualinput pairs are free to take on independent common modelevels, while the two voltage differentials are summedinternally to form a net input signal.
上传时间： 2014-12-23
上传用户：13691535575
A fully differential amplifi er is often used to converta single-ended signal to a differential signal, a designwhich requires three signifi cant considerations: theimpedance of the single-ended source must match thesingle-ended impedance of the differential amplifi er,the amplifi er’s inputs must remain within the commonmode voltage limits and the input signal must be levelshifted to a signal that is centered at the desired outputcommon mode voltage.
上传时间： 2013-11-09
上传用户：wweqas
Most circuit designers are familiar with diode dynamiccharacteristics such as charge storage, voltage dependentcapacitance and reverse recovery time. Less commonlyacknowledged and manufacturer specifi ed is diode forwardturn-on time. This parameter describes the timerequired for a diode to turn on and clamp at its forwardvoltage drop. Historically, this extremely short time, unitsof nanoseconds, has been so small that user and vendoralike have essentially ignored it. It is rarely discussed andalmost never specifi ed. Recently, switching regulator clockrate and transition time have become faster, making diodeturn-on time a critical issue. Increased clock rates aremandated to achieve smaller magnetics size; decreasedtransition times somewhat aid overall effi ciency but areprincipally needed to minimize IC heat rise. At clock speedsbeyond about 1MHz, transition time losses are the primarysource of die heating.
上传时间： 2013-10-10
上传用户：谁偷了我的麦兜
