以太网和CAN总线应用广泛，但由于其通信协议不同，两种总线器件间无法进行数据通信，因此，设计了基于CP2200与C8051F040的以太网总线与CAN总线接口转换电路，并给出部分相关硬件电路与软件设计分析。在保证数据完整和协议可靠的前提下，通过握手协议和简化的以太网协议，不仅实现了以太网数据与CAN数据的转发，同时还顺利的解决了以太网的高速性与CAN的低速率冲突，以及两者数据包之间的大小不同的矛盾。 Abstract: In the development of actual application， Ethernet and CAN bus are used very extensively. Owing to its various communication protocols， the communicating between two kinds of bus device can’t be carried out. Therefore， in order to solve this problem， the Ethernet-CAN bus interface circuit based on CP2200 and C8051F040 was designed in this paper， and part of the related hardware circuit and software design analysis were given. On the condition of data’s integrity and protocols’reliability， through the handshaking protocols and the simplified the Ethernet protocol， not only the data switching between CAN and Ethernet was realized， but also the differ in velocity and packet size was solved.
上传时间： 2013-10-15
上传用户：Ants
单片机作为一种微型计算机，其内部具有一定的存储单元（8031除外），但由于其内部存储单元及端口有限，很多情况下难以满足实际需求。为此介绍一种新的扩展方法，将数据线与地址线合并使用，通过软件控制的方法实现数据线与地址线功能的分时转换，数据线不仅用于传送数据信号，还可作为地址线、控制线，用于传送地址信号和控制信号，从而实现单片机与存储器件的有效连接。以单片机片外256KB数据存储空间的扩展为例，通过该扩展方法，仅用10个I/O端口便可实现，与传统的扩展方法相比，可节约8个I/O端口。 Abstract: As a micro-computer,the SCM internal memory has a certain units(except8031),but because of its internal storage units and the ports are limited,in many cases it can not meet the actual demand.So we introduced a new extension method,the data line and address lines combined through software-controlled approach to realize the time-conversion functions of data lines and address lines,so the data lines not only transmited data signals,but also served as address lines and control lines to transmit address signals and control signals,in order to achieve an effective connection of microcontroller and memory chips.Take microcontroller chip with256KB of data storage space expansion as example,through this extension method,with only10I/O ports it was achieved,compared with the traditional extension methods,this method saves8I/O ports.
上传时间： 2014-12-26
上传用户：adada
针对目前汽车追尾事件频发问题，提出一种防汽车车前和车后追尾的安全装置设计。该设计以高性能、低功耗的8位AVR微处理器ATmega8L为核心，结合霍尔式车速传感器、激光雷达测距装置和MMA7260QT加速度传感器，能够兼顾车前和车后，摒弃以往设计中只考虑车前或车后单一性缺点，尤其适用于高速、夜晚或新手行车。 Abstract: Aiming at the high frequency of vehicle rear-end collision，a safe device design of anti-vehicle rear-end collision is presented.In the design，the high-performance，low-power8-bit AVR microprocessor ATmega8L is utilized as a core combined with Hall-type speed sensor，laser-radar ranging devices and the acceleration sensor MMA7260QT.The design considers both the front and back of a car，and overcomes the drawbacks of former designs in which only the front or the back of the car is considered，so it is especially suitable for high-speed，night or the beginner’s driving.
上传时间： 2013-10-14
上传用户：GavinNeko
该系统由单片机89S52控制模块，程控宽带放大模块，整形模块，FPGA内频率、相位差测量模块等构成，采用等精度测频法测出频率和周期，可测量有效值为0.01～5V，频率范围1Hz～20MHz信号的频率、周期信号，精度高达10-6。采用计数法测量相位差，该系统可测量有效值0.5～5V，频率10Hz～100kHz信号的相位差，精度为1°。系统功能由按键控制，测量结果实时显示，人机界面友好。 Abstract: The system consists of the following functional blocks:89S52microcontroller controlling module,programmable amplifier module,comparator module,frequency and phase difference testing module in the FPGA.The system use the equal accuracy frequency-examining technique it measures frequency and circle of signal which its ranges is from1Hz to20MHz and the amplitude of which its range is from0.01Vrms to5Vrms,precision is up to10-6.Using of count method,the system detects the phase difference of signal,the amplitude of whic its range is from0.5Vrms to5Vrms and the frequency of which its ranges is from10Hz to100kHz,precision is up to1°,The system functions is controlled by certain keys,measurement results are displayed in real-time and it is friendly interface.
上传时间： 2013-11-04
上传用户：CHINA526
以89S52单片机和EP1C6Q240C8型FPGA为控制核心的多功能计数器，是由峰值检波、A/D转换、程控放大、比较整形、移相网络部分组成,可实现测量正弦信号的频率、周期和相位差的功能。多功能计数器采用等精度的测量方法，可实现频率为1Hz～10MHz、幅度为0.01～5Vrms的正弦信号的精确测频，以及频率为10Hz～100kHz、幅度为0.5～5Vrms的正弦信号精确测相。液晶显示器能够实时显示当前信号的频率、周期和相位差。该多功能计数器精度高，界面友好，实用性强。 Abstract: A multi-function counter，which uses89S52MCU and EP1C6Q240C8FPGA as a control core，consists of peak detector，A/D conversion，program-controlled amplification，compared shaping and phase-shifting network part.The counter measures the frequency，period and phase of sinusoidal signal.With the equal precision method,the multi-function counter achieves the precise frequency measurement of the sinusoidal signal which its frequency is from1Hz to10MHz，its amplitude is from0.01Vrms to5Vrms，as well as the accurate phase measurement of the sinusoidal signal which its frequency is from10Hz to100kHz，its amplitude is from0.5Vrms to5Vrms.The LCD monitor real-time displays the frequency，period and phase difference of current signal.The multi-function counter features high precision，friendly interface，and strong practical.
上传时间： 2013-11-15
上传用户：gy592333
介绍了当前普通标记机控制系统现状及其存在缺点，给出气动标记机及相频修正PWM模式的工作原理。采用ATmega16单片机和USB转换RS232接口器件CH341T实现驱动控制系统与PC的实时通讯，标记控制系统可升级到USB接口。采用基于ATmega16的相频修正PWM替换555振荡电路产生的PWM，可直接通过软件调整PWM信号。使用达林顿三极管TIP122替代直流继电器驱动高频电磁阀，使得电磁阀驱动电路简单，成本低廉。该控制系统已成功应用于气动标记机。 Abstract: In this paper,the actuality and demerit of the common gas marking machine control systems are described.The operation principle of the gas marking machine and the phase and frequency correct PWM of ATmega16is introduced.The real-time communication between the driving control system and PC by CH341T which its function is translated USB to RS232is realized,the control systems is updated grade to USB interface.The PWM signal can be adjustable by software for the555surge circuit was substituted by the phase and frequency.The high frequency electromagnetic value’s driving circuit by DC relay is replaced by TIP122,therefore,the circuit is become simple and the cost cheap.The control systems has been widely used in gas marking machine.
上传时间： 2013-10-18
上传用户：1427796291
介绍了采用ATmega48单片机实现三相无刷直流电机控制器的方法。利用Atmega48获得带死区的脉宽调制（PWM）、霍尔传感器的换相处理、正弦驱动信号的产生和电机转速的控制等功能。采用该方法的优点是所需的外围器件少，成本低。 Abstract: The method of 3-phase brushless DC motor control based on ATmega48 is presented in this paper.The system uses ATmega48 to generate PWM signals with dead-time, hall sensors signals commutation，sine driving signal and rotational speed of motor.Using this method，the needed external devices are few, the cost is low.
上传时间： 2013-12-09
上传用户：330402686
Mega16是一款采用先进RISC精简指令，内置A/D的8位单片机，可支持低电压联机 Flash和EEPROM 写入功能；同时还支持 Basic和C 等高级语言编程。用它设计电子时钟不仅成本低，硬件简单，而且很容易实现系统移植。介绍了如何利用AVR系列单片机Mega16及1602字符液晶来设计电子时钟的方法，同时给出了相应的电路原理及部分语言程序。 Abstract: ?Mega16 is a high-performance, low power consumption, the use of advanced RISC concise instructions, built-in A/D 8-bit microcontrollers, the on-line support for low-voltage Flash, EEPROM write function. Except Mega16 also support the Basic, C, and other high-level language programming.The electronic clock which is deisgned by Mega16 is not only low-cost, simple hardware, but easy to achieve system migration.The design method of electrioic clock based on the AVR Mega16 and character LCD1602 is introduced in this paper,and the corresponding circuit electrionic and some language program are given.
上传时间： 2014-12-27
上传用户：zl5712176
以AVR单片机ATmega8和USB接口器件PDIUSBD12为核心，基于标准的USB1.1协议，设计一种通用USB接口模块，以满足嵌入式系统中对USB接口的需求。对模块的硬件电路或单片机固件程序的硬件接口层稍加修改即可用于其他各种微处理器。该模块可为各种嵌入式系统增加USB接口,实现与USB主机系统通信。 Abstract: Based on AVR microcontroller ATmega8 and USB interface chip PDIUSBD12, a general USB interface module is designed according to USB1.1 protocol for various requirements of embedded systems. Only with few modifications in circuit or hardware abstract layer of firmware, the module can be used on many types of microprocessors. All kinds of embedded systems can realize high speed and stable communication with USB host systems, owing to the facility of this module.
上传时间： 2014-01-08
上传用户：赵云兴
介绍了电力操作电源与智能电池巡检系统的特点，给出了一种基于超低功耗单片机MSP430 F149针对中小型变电站自动化运行的专用设备的基本设计原理及实现方法，最后给出了详细硬件构成和软件实现。该系统能满足中小型变电站安全、可靠、自动运行的要求，并通过与上位机的串行通信实现变电站的远程管理和控制。 Abstract: The characters of the intelligent battery data logging system of the electric operation power are introduced.The basic design principle and the implemented methods of the special equipment which only designed for the middle or small transformer substation based on MSP430F149 are prescribed. Finally, the hardware block diagram and the software flow chart are also given. The function that the system finally needs to realize can basically meet with the middle or small transformer substation’s satisfy, reliably,and automatic running.And it can also realize the transformer substation long-distance management and control by serial communicating with the host computer.
上传时间： 2013-11-25
上传用户：黄华强
