The LTC®3414 offers a compact and efficient voltage regulatorsolution for point of load conversion in electronicsystems that require low output voltages (down to 0.8V)from a 2.5V to 5V power bus. Internal power MOSFETswitches, with only 67mW on-resistance, allow theLTC3414 to deliver up to 4A of output current with efficiencyas high as 94%. The LTC3414 saves space by operatingwith switching frequencies as high as 4MHz, enabling theuse of tiny inductors and capacitors.
上传时间： 2014-01-03
上传用户：dongbaobao
While simplicity and high effi ciency (for cool running) areno longer optional features in isolated power supplies, itis traditionally diffi cult to achieve both. Achieving higheffi ciency often requires the use of advanced topologiesand home-brewed secondary synchronous rectifi cationschemes once reserved only for higher power applications.This only adds to the parts count and to the designcomplexity associated with the reference and optocouplercircuits typically used to maintain isolation. Fortunately, abreakthrough IC makes it possible to achieve both high efficiency and simplicity in a synchronous fl yback topology.The LT®3825 simplifi es and improves the performance oflow voltage, high current fl yback supplies by providingprecise synchronous rectifi er timing and eliminating theneed for optocoupler feedback while maintaining excellentregulation and superior loop response.
上传时间： 2013-10-16
上传用户：wayne595
Handheld designers often grapple with ways to de-bounceand control the on/off pushbutton of portable devices.Traditional de-bounce designs use discrete logic, fl ipflops, resistors and capacitors. Other designs includean onboard microprocessor and discrete comparatorswhich continuously consume battery power. For highvoltage multicell battery applications, a high voltageLDO is needed to drive the low voltage devices. All thisextra circuitry not only increases required board spaceand design complexity, but also drains the battery whenthe handheld device is turned off. Linear Technology addressesthis pushbutton interface challenge with a pairof tiny pushbutton controllers.
上传时间： 2013-11-18
上传用户：ZJX5201314
Today’s computer, datacom, and telecom systems demandpower supplies that are effi cient, respond quicklyto load transients and accurately regulate the voltageat the load. For example, load current can be measuredby using the inductor DCR, thus eliminating the needfor a dedicated sense resistor. Inductor DCR sensingincreases effi ciency—especially at heavy load—whilereducing component cost and required board space.The LTC®3856 single-output 2-phase synchronous buckcontroller improves the accuracy of inductor DCR sensingby compensating for changes in DCR due to temperature.
上传时间： 2013-11-05
上传用户：guobing703
Once relegated to the hinterlands of low cost indicatorlights, the LED is again in the spotlight of the lightingworld. LED lighting is now ubiquitous, from car headlightsto USB-powered lava lamps. Car headlights exemplifyapplications that capitalize on the LED’s clear advantages—unwavering high quality light output, tough-assteelrobustness, inherent high effi ciency—while a USBlava lamp exemplifi es applications where only LEDs work.Despite these clear advantages, their requirement forregulated voltage and current make LED driver circuitsmore complex than the venerable light bulb, but some newdevices are closing the gap. For instance, the LTM®8040μModule™ LED driver integrates all the driver circuitryinto a single package, allowing designers to refocus theirtime and effort on the details of lighting design criticalto a product’s success.
上传时间： 2013-10-16
上传用户：togetsomething
One of the fi rst lessons in a basic electronics coursecovers the symbols for resistors, capacitors, inductors,voltage sources and current sources. Althougheach symbol represents a functional component of areal-world circuit, only some of the symbols have directphysical counterparts. For instance, the three discretepassive devices—resistors, capacitors, inductors—canbe picked off a shelf and placed on a real board muchas their symbolic analogs appear in a basic schematic.Likewise, while voltage sources have no direct 2-terminalanalog, a voltage source can be easily built with an offthe-shelf linear regulator.
上传时间： 2013-11-24
上传用户：simonpeng
What would happen if someone connected 24V to your12V circuits? If the power and ground lines were inadvertentlyreversed, would the circuits survive? Does yourapplication reside in a harsh environment, where the inputsupply can ring very high or even below ground? Evenif these events are unlikely, it only takes one to destroya circuit board.
上传时间： 2013-10-26
上传用户：jackandlee
Specifying the right reference and applying it correctly isa more difficult task than one might first surmise, consideringthat references are only 2- or 3-terminal devices.Although the word “accuracy” is most often spoken inreference to references, it is dangerous to use this wordtoo freely because it can mean different things to differentpeople. Even more perplexing is the fact that a referenceclassified as a dog in one application is a panacea inanother. This application note will familiarize the readerwith the various aspects of reference “accuracy” andpresent some tips on extracting maximum performancefrom any reference.
标签： 电压基准
上传时间： 2013-10-15
上传用户：liuwei6419
Telecommunication, satellite links and set-top boxes allrequire tuning a high frequency oscillator. The actualtuning element is a varactor diode, a 2-terminal device thatchanges capacitance as a function of reverse bias voltage.1 The oscillator is part of a frequency synthesizingloop, as detailed in Figure 1. A phase locked loop (PLL)compares a divided down representation of the oscillatorwith a frequency reference. The PLL’s output is levelshifted to provide the high voltage necessary to bias thevaractor, which closes a feedback loop by voltage tuningthe oscillator. This loop forces the voltage controlledoscillator (VCO) to operate at a frequency determined bythe frequency reference and the divider’s division ratio.
上传时间： 2013-12-20
上传用户：ABCDE
As logic systems get larger and more complex, theirsupply current requirements continue to rise. Systemsrequiring 100A are fairly common. A high current powersupply to meet such requirements usually requires parallelingseveral power regulators to alleviate the thermalstress on the individual power components. A powersupply designer is left with the choice of how to drive theseparalleled regulators: brute-force single-phase or smartPolyPhaseTM.
上传时间： 2013-10-08
上传用户：zhqzal1014
