The PCA9548A is an octal bidirectional translating switch controlled via the I2C-bus. TheSCL/SDA upstream pair fans out to eight downstream pairs, or channels. Any individualSCx/SDx channel or combination of channels can be selected, determined by thecontents of the programmable control register.An active LOW reset input allows the PCA9548A to recover from a situation where one ofthe downstream I2C-buses is stuck in a LOW state. Pulling the RESET pin LOW resets theI2C-bus state machine and causes all the channels to be deselected as does the internalPower-on reset function.
上传时间： 2013-10-13
上传用户：bakdesec
The PCA9674/74A is a drop-in upgrade for the PCF8574/74A providing higher Fast-modePlus I2C-bus speeds (1 MHz versus 400 kHz) so that the output can support PWMdimming of LEDs, higher I2C-bus drive (30 mA versus 3 mA) so that many more devicescan be on the bus without the need for bus buffers, higher total package sink capacity(200 mA versus 100 mA) that supports having all LEDs on at the same time and moredevice addresses (64 versus 8) are available to allow many more devices on the buswithout address conflicts.
上传时间： 2013-10-22
上传用户：wwwwwen5
The TRS232E is a dual driver/receiver that includes a capacitive voltage generator to supply TIA/RS-232-Fvoltage levels from a single 5-V supply. Each receiver converts TIA/RS-232-F inputs to 5-V TTL/CMOS levels.This receiver has a typical threshold of 1.3 V, a typical hysteresis of 0.5 V, and can accept ±30-V inputs. Eachdriver converts TTL/CMOS input levels into TIA/RS-232-F levels. The driver, receiver, and voltage-generatorfunctions are available as cells in the Texas Instruments LinASIC™ library.
上传时间： 2013-10-07
上传用户：waitingfy
The main oscillator allows either a crystal or single-ended input clock signal. Cost-sensitiveapplications typically use an external crystal with the on-chip oscillator circuit since it is the mostcost-effective solution. It is also possible to use the internal oscillator to clock the device after theboot process has completed.
标签： Stellaris Clocking Options for
上传时间： 2013-10-14
上传用户：pol123
The MAX3243E device consists of three line drivers, five line receivers, and a dual charge-pump circuit with±15-kV ESD (HBM and IEC61000-4-2, Air-Gap Discharge) and ±8-kV ESD (IEC61000-4-2, Contact Discharge)protection on serial-port connection pins. The device meets the requirements of TIA/EIA-232-F and provides theelectrical interface between an asynchronous communication controller and the serial-port connector. Thiscombination of drivers and receivers matches that needed for the typical serial port used in an IBM PC/AT, orcompatible. The charge pump and four small external capacitors allow operation from a single 3-V to 5.5-Vsupply. In addition, the device includes an always-active noninverting output (ROUT2B), which allowsapplications using the ring indicator to transmit data while the device is powered down. The device operates atdata signaling rates up to 250 kbit/s and a maximum of 30-V/ms driver output slew rate.
标签： MULTICHANNEL 5.5 TO RS
上传时间： 2013-10-19
上传用户：ddddddd
基于PIC单片机的脉冲电源:设计了一种金属凝固过程用脉冲电源。该电源采用PIC16F877作为主控芯片，实现对窄脉冲电流幅值的检测，以及时电流脉冲幅值根据模糊PID算法进行闲环控制。使用结果表明：该电源的输出脉冲波形良好，电流幅值稳定，满足合金材料凝固过程的工艺要求且运行稳定可靠。关键词：脉冲电源；PIC16F877单片机；模糊PID；闲环控制 Abstract：A kind of pulse power supply was designed which uses in the metal solidification process ．．I11is power supply used PIC16F877 to take the master control chip reali on to the narrow pulse electric current peak-to-peak value examination，carried on the closed-loop control to the electric current pulse peak-to-peak value basis fuzzy PID algorithm．The use result indicated ，this power supply output se profile is good，and the electric current peak-to-p~k value is stable，It satisfies the alloy material solidification process the technological requirement and movement stable reliable，Key words：p se po wer supply；PIC16F877single-chip microcontroller；f r PID；closed-loop control
上传时间： 2013-10-27
上传用户：xcy122677
高压双管反激变换器的设计:介绍一种双管反激的电路拓扑，分析了其工作原理，给出了一些关键技术参数的计算公式，设计并研制成功的30W 380V AC5 0H z/510V DC/+15.1 V DC(1A )、+5.2VDC(2A)辅助开关电源具有功率密度高、变换效率高、可靠性高等优良的综合性能。该变换器在高电压输人情况下有重要的应用价值。【关 键 词 】变换器，辅助开关电源，双管反激 [Abstract】 A n e wt opologyfo rd oubles witchfl ybackc onverteris in troduced.Th eo perationp rincipleis a nalyzeda nds ome for mulas for calculating key parameters for the topology are presented. The designed and produced auxiliary switching power supply,i. e. 30W 380V AC5 0H z/5 10V DC/+15.1 V DC《1A )、+5.2 V DC《2A )，hase xcellentc omprehensivep erformances sucha sh ighp owerd ensity, hi ghc onversione fficiencya ndh ighr eliability.Th isc onverterh asim portanta pplicationv aluef orh igh input voltag [Keywords ]converter,au xiliary switchingp owers upply,do ubles witchf lybac
上传时间： 2013-11-01
上传用户：Ants
Internal Interrupts are used to respond to asynchronous requests from a certain part of themicrocontroller that needs to be serviced. Each peripheral in the TriCore as well as theBus Control Unit, the Debug Unit, the Peripheral Control Processor (PCP) and the CPUitself can generate an Interrupt Request.So what is an external Interrupt?An external Interrupt is something alike as the internal Interrupt. The difference is that anexternal Interrupt request is caused by an external event. Normally this would be a pulseon Port0 or Port1, but it can be even a signal from the input buffer of the SSC, indicatingthat a service is requested.The User’s Manual does not explain this aspect in detail so this ApNote will explain themost common form of an external Interrupt request. This ApNote will show that there is aneasy way to react on a pulse on Port0 or Port1 and to create with this impulse an InterruptService Request. Later in the second part of the document, you can find hints on how todebounce impulses to enable the use of a simple switch as the input device.Note: You will find additional information on how to setup the Interrupt System in theApNote “First steps through the TriCore Interrupt System” (AP3222xx)1. It would gobeyond the scope of this document to explain this here, but you will find selfexplanatoryexamples later on.
上传时间： 2013-10-27
上传用户：zhangyigenius
The Infineon TriCore provides an Interrupt System with a high safety standard. Thisdocument contains some instructions on how to initiate an Interrupt from an externaldevice. First it will show you how to trigger an Interrupt Service Request by an impulseon Port 0 or Port 1. Then in the second part of the document you can find hints how todebounce impulses to enable the use of a simple switch as input device.Authors: Thomas Bliem, CQ Nguyen / Infineon SMI MD Apps
上传时间： 2013-11-05
上传用户：uuuuuuu
This application note describes how to build a system that can be used for determining theoptimal phase shift for a Double Data Rate (DDR) memory feedback clock. In this system, theDDR memory is controlled by a controller that attaches to either the OPB or PLB and is used inan embedded microprocessor application. This reference system also uses a DCM that isconfigured so that the phase of its output clock can be changed while the system is running anda GPIO core that controls that phase shift. The GPIO output is controlled by a softwareapplication that can be run on a PowerPC® 405 or Microblaze™ microprocessor.
上传时间： 2013-10-15
上传用户：euroford
