为提升虚拟仪器传输速率与实时性能，扩展监测范围，在VC的软件平台上设计了一种全功能虚拟示波器。与传统虚拟示波器相比，该系统采用嵌入式系统完成信号采集，采用工业以太网为传输介质，通过线性插值算法和多线程编程思想，实现波形显示、参数计算、频谱分析以及波形存储及回放功能。实验结果表明，该虚拟示波器可以实现20 kHz采样频率下的波形精确显示，达到预期的各项指标。 Abstract: o enhance the transfer rate and real-time of virtual instrument performance， expand scope of monitoring， this paper uses the VCs software platform to design a fully functional virtual oscilloscope. Compared with traditional virtual oscilloscope， this system adopts the embedded system to complete the data acquisition， industrial Ethernet as the transmission medium used by the linear interpolation algorithm and multi-threaded programming ideas， namely to achieve waveform display， parameter calculation， spectrum analysis and waveform storage and playback. Experimental results show that the virtual oscilloscope can accurately display the waveform with 20kHz sampling frequency， and achieve the desired targets.
上传时间： 2013-11-25
上传用户：wbwyl
多远程二极管温度传感器-Design Considerations for pc thermal management Multiple RDTS (remote diode temperature sensing) provides the most accurate method of sensing an IC’s junction temperature. It overcomes thermal gradient and placement issues encountered when trying to place external sensors. PCB component count decreases when using a device that provides multiple inputs.Better temperature sensing improves product performance and reliability. Disk drive data integrity suffers at elevated temperatures. IBM published an article stating that a 5°C rise in operating temperature causes a 15% increase in the drive’s failure rate. The overall performance of a system can be improved by providing a more accurate temperature measurement of the most critical devices allowing them to run just a few degrees hotter.The LM83 directly senses its own temperature and the temperature of three external PN junctions. One is dedicated to the CPU of choice, the other two go to other parts of your system that need thermal monitoring such as the disk drive or graphics chip. The SMBus-compatible LM83 supports SMBus timeout and logic levels. The LM83 has two interrupt outputs; one for user-programmable limits and WATCHDOG capability (INT), the other is a Critical Temperature Alarm output (T_CRIT_A) for system power supply shutdown.
标签： Considerat Design 远程 二极管
上传时间： 2014-12-21
上传用户：ljd123456
The LPC2292/2294 microcontrollers are based on a 16/32-bit ARM7TDMI-S CPU with real-time emulation and embedded trace support, together with 256 kB of embedded high-speed flash memory. A 128-bit wide memory interface and a unique accelerator architecture enable 32-bit code execution at the maximum clock rate. For critical code size applications, the alternative 16-bit Thumb mode reduces code by more than 30 pct with minimal performance penalty. With their 144-pin package, low power consumption, various 32-bit timers, 8-channel 10-bit ADC, 2/4 (LPC2294) advanced CAN channels, PWM channels and up to nine external interrupt pins these microcontrollers are particularly suitable for automotive and industrial control applications as well as medical systems and fault-tolerant maintenance buses. The number of available fast GPIOs ranges from 76 (with external memory) through 112 (single-chip). With a wide range of additional serial communications interfaces, they are also suited for communication gateways and protocol converters as well as many other general-purpose applications. Remark: Throughout the data sheet, the term LPC2292/2294 will apply to devices with and without the /00 or /01 suffix. The suffixes /00 and /01 will be used to differentiate from other devices only when necessary.
上传时间： 2014-12-30
上传用户：aysyzxzm
针对UHF读写器设计中，在符合EPC Gen2标准的情况下，对标签返回的高速数据进行正确解码以达到正确读取标签的要求，提出了一种新的在ARM平台下采用边沿捕获统计定时器数判断数据的方法，并对FM0编码进行解码。与传统的使用定时器定时采样高低电平的FM0解码方法相比，该解码方法可以减少定时器定时误差累积的影响；可以将捕获定时器数中断与数据判断解码相对分隔开，使得中断对解码影响很小，实现捕获与解码的同步。通过实验表明，这种方法提高了解码的效率，在160 Kb/s的接收速度下，读取一张标签的时间约为30次/s。 Abstract: Aiming at the requirement of receiving correctly decoded data from the tag under high-speed communication which complied with EPC Gen2 standard in the design of UHF interrogator， the article introduced a new technology for FM0 decoding which counted the timer counter to judge data by using the edge interval of signal capture based on the ARM7 platform. Compared with the traditional FM0 decoding method which used the timer timed to sample the high and low level， the method could reduce the accumulation of timing error and could relatively separate capture timer interrupt and the data judgment for decoding， so that the disruption effect on the decoding was small and realizd synchronization of capture and decoding. Testing result shows that the method improves the efficiency of decoding， at 160 Kb/s receiving speed， the time of the interrogator to read a tag is about 30 times/s.
上传时间： 2013-11-10
上传用户：liufei
同步技术是跳频通信系统的关键技术之一，尤其是在快速跳频通信系统中，常规跳频通信通过同步字头携带相关码的方法来实现同步，但对于快跳频来说，由于是一跳或者多跳传输一个调制符号，难以携带相关码。对此引入双跳频图案方法，提出了一种适用于快速跳频通信系统的同步方案。采用短码携带同步信息，克服了快速跳频难以携带相关码的困难。分析了同步性能，仿真结果表明该方案同步时间短、虚警概率低、捕获概率高，同步性能可靠。 Abstract: Synchronization is one of the key techniques to frequency-hopping communication system， especially in the fast frequency hopping communication system. In conventional frequency hopping communication systems， synchronization can be achieved by synchronization-head which can be used to carry the synchronization information， but for the fast frequency hopping， Because modulation symbol is transmitted by per hop or multi-hop， it is difficult to carry the correlation code. For the limitation of fast frequency hopping in carrying correlation code， a fast frequency-hopping synchronization scheme with two hopping patterns is proposed. The synchronization information is carried by short code， which overcomes the difficulty of correlation code transmission in fast frequency-hopping. The performance of the scheme is analyzed， and simulation results show that the scheme has the advantages of shorter synchronization time， lower probability of false alarm， higher probability of capture and more reliable of synchronization.
上传时间： 2013-11-23
上传用户：mpquest
The NXP LPC315x combine an 180 MHz ARM926EJ-S CPU core, High-speed USB 2.0OTG, 192 KB SRAM, NAND flash controller, flexible external bus interface, an integratedaudio codec, Li-ion charger, Real-Time Clock (RTC), and a myriad of serial and parallelinterfaces in a single chip targeted at consumer, industrial, medical, and communicationmarkets. To optimize system power consumption, the LPC315x have multiple powerdomains and a very flexible Clock Generation Unit (CGU) that provides dynamic clockgating and scaling.The LPC315x is implemented as multi-chip module with two side-by-side dies, one fordigital fuctions and one for analog functions, which include a Power Supply Unit (PSU),audio codec, RTC, and Li-ion battery charger.
上传时间： 2014-01-17
上传用户：Altman
Today in many applications such as network switches, routers, multi-computers,and processor-memory interfaces, the ability to integrate hundreds of multi-gigabit I/Os is desired to make better use of the rapidly advancing IC technology.
上传时间： 2013-10-30
上传用户：ysjing
This example shows how to update at regulate period the WWDG counter using theEarly Wakeup interrupt (EWI). The WWDG timeout is set to 262ms, refresh window set to 41h and the EWI isenabled. When the WWDG counter reaches 40h the EWI is generated and in the WWDGISR the counter is refreshed to prevent a WWDG reset and led connected to PC.07is toggled.The EXTI line9 is connected to PB.09 pin and configured to generate an interrupton falling edge.In the NVIC, EXTI line9 to 5 interrupt vector is enabled with priority equal to 0and the WWDG interrupt vector is enabled with priority equal to 1 (EXTI IT > WWDG IT). The EXTI Line9 will be used to simulate a software failure: once the EXTI line9event occurs (by pressing Key push-button on EVAL board) the correspondent interruptis served, in the ISR the led connected to PC.07 is turned off and the EXTI line9pending bit is not cleared. So the CPU will execute indefinitely EXTI line9 ISR andthe WWDG ISR will never be entered(WWDG counter not updated). As result, when theWWDG counter falls to 3Fh the WWDG reset occurs.If the EXTI line9 event don抰 occurs the WWDG counter is indefinitely refreshed inthe WWDG ISR which prevent from WWDG reset. If the WWDG reset is generated, after resuming from reset a led connected to PC.06is turned on. In this example the system is clocked by the HSE(8MHz).
上传时间： 2013-11-11
上传用户：gundamwzc
#include <reg51.h>#include <main.h>#include <interrupt.h> cs5460a应用电路(含源程序)bit code table_odd_even_bit[16]={0,1,1,0,1,0,0,1,1,0,0,1,0,1,1,0}; extern uchar rs485_timeout,pointer_buf485;extern uchar rs485_buf[MAX_485_LEN];extern uchar idata spi_buf[MAX_SPI_LEN];extern uchar pointer_send,send_len; extern uchar count_1s;//extern uint count_2min;extern uint count_10s;extern uchar oper_len,send_offset,chk_sum,send_i;extern bit flag_send_data,flag_level,flag_drdy,flag_data_ok;
上传时间： 2014-01-24
上传用户：heart_2007
ARM通讯 H-JTAG 是一款简单易用的的调试代理软件，功能和流行的MULTI-ICE 类似。H-JTAG 包括两个工具软件：H-JTAG SERVER 和H-FLASHER。其中，H-JTAG SERVER 实现调试代理的功能，而H-FLASHER则实现了FLASH 烧写的功能。H-JTAG 的基本结构如下图1-1所示。 H-JTAG支持所有基于ARM7 和ARM9的芯片的调试，并且支持大多数主流的ARM调试软件，如ADS、RVDS、IAR 和KEIL。通过灵活的接口配置，H-JTAG 可以支持WIGGLER，SDT-JTAG 和用户自定义的各种JTAG 调试小板。同时，附带的H-FLASHER 烧写软件还支持常用片内片外FLASH 的烧写。使用H-JTAG，用户能够方便的搭建一个简单易用的ARM 调试开发平台。H-JTAG 的功能和特定总结如下： 1. 支持 RDI 1.5.0 以及 1.5.1； 2. 支持所有ARM7 以及 ARM9 芯片； 3. 支持 THUMB 以及ARM 指令； 4. 支持 LITTLE-ENDIAN 以及 BIG-ENDIAN； 5. 支持 SEMIHOSTING； 6. 支持 WIGGLER， SDT-JTAG和用户自定义JTAG调试板； 7. 支持 WINDOWS 9.X/NT/2000/XP； 8．支持常用FLASH 芯片的编程烧写； 9. 支持LPC2000 和AT91SAM 片内FLASH 的自动下载；
上传时间： 2014-12-01
上传用户：Miyuki
